On Fri, Dec 08, 2017 at 03:33:00PM +0100, Rasmus Villemoes wrote:
> The LS1021A allows inverting the polarity of six interrupt lines
> IRQ[0:5] via the scfg_intpcr register, effectively allowing
> IRQ_TYPE_LEVEL_LOW and IRQ_TYPE_EDGE_FALLING for those. We just need to
> check the type, set the relevant bit in INTPCR accordingly, and fixup
> the type argument before calling the GIC's irq_set_type.
>
> In fact, the power-on-reset value of the INTPCR register is so that all
> six lines have their polarity inverted. Hence any hardware connected to
> those lines is unusable without this: If the line is indeed active low,
> the generic GIC code will reject an irq spec with IRQ_TYPE_LEVEL_LOW,
> while if the line is active high, we must obviously disable the polarity
> inversion before unmasking the interrupt.
>
> I suspect other layerscape SOCs may have something similar, but I have
> neither hardware nor documentation.
>
> Since we only need to keep a single pointer in the chip_data (the syscon
> regmap), the code could be a little simpler by dropping the struct
> extirq_chip_data and just store the regmap directly - but I don't know
> if I do need to add a lock or something else to the chip_data, so for
> this RFC I've kept the struct.
>
> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@xxxxxxxxx>
> ---
> Marc, Alexander, thanks a lot for your hints. This is what I came up
> with, mostly just copy-pasted from the mtk-sysirq case. I've tested
> that it works as expected on my board.
>
> .../interrupt-controller/fsl,ls1021a-extirq.txt | 19 +++
Please split to separate patch.
> drivers/irqchip/Makefile | 1 +
> drivers/irqchip/irq-ls1021a.c | 157 +++++++++++++++++++++
> 3 files changed, 177 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/interrupt-controller/fsl,ls1021a-extirq.txt
> create mode 100644 drivers/irqchip/irq-ls1021a.c
>
> diff --git a/Documentation/devicetree/bindings/interrupt-controller/fsl,ls1021a-extirq.txt b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls1021a-extirq.txt
> new file mode 100644
> index 000000000000..53b04b6e1a80
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls1021a-extirq.txt
> @@ -0,0 +1,19 @@
> +* Freescale LS1021A external IRQs
> +
> +The LS1021A supports inverting the polarity of six external interrupt lines.
> +
> +Required properties:
> +- compatible: should be "fsl,ls1021a-extirq"
> +- interrupt-controller: Identifies the node as an interrupt controller
> +- #interrupt-cells: Use the same format as specified by GIC in arm,gic.txt.
> +- interrupt-parent: phandle of GIC.
> +- syscon: phandle of Supplemental Configuration Unit (scfg).
Can this be a child of that node instead?
> +
> +Example:
> + extirq: interrupt-controller@15701ac {
Unit-address without reg is not valid. Building with W=1 will tell you
this.
> + compatible = "fsl,ls1021a-extirq";
> + #interrupt-cells = <3>;
> + interrupt-controller;
> + interrupt-parent = <&gic>;
> + syscon = <&scfg>;
> + };
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
