Re: [PATCH v3 2/3] mailbox: Add support for Hi3660 mailbox

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Fri, Nov 17, 2017 at 2:54 PM, Xu YiPing <xuyiping@xxxxxxxxxxxxx> wrote:
> From: Kaihua Zhong <zhongkaihua@xxxxxxxxxx>
>
> Hi3660 mailbox controller is used to send message within multiple
> processors, MCU, HIFI, etc.  It supports 32 mailbox channels and every
> channel can only be used for single transferring direction.  Once the
> channel is enabled, it needs to specify the destination interrupt and
> acknowledge interrupt, these two interrupt vectors are used to create
> the connection between the mailbox and interrupt controllers.
>
> The data transferring supports two modes, one is named as "automatic
> acknowledge" mode so after send message the kernel doesn't need to wait
> for acknowledge from remote and directly return; there have another mode
> is to rely on handling interrupt for acknowledge.
>
> This commit is for initial version driver, which only supports
> "automatic acknowledge" mode to support CPU clock, which is the only
> one consumer to use mailbox and has been verified.  Later may enhance
> this driver for interrupt mode (e.g. for supporting HIFI).
>
> Signed-off-by: Leo Yan <leo.yan@xxxxxxxxxx>
> Signed-off-by: Ruyi Wang <wangruyi@xxxxxxxxxx>
> Signed-off-by: Kaihua Zhong <zhongkaihua@xxxxxxxxxx>
> ---
>  drivers/mailbox/Kconfig          |   8 +
>  drivers/mailbox/Makefile         |   2 +
>  drivers/mailbox/hi3660-mailbox.c | 322 +++++++++++++++++++++++++++++++++++++++
>  3 files changed, 332 insertions(+)
>  create mode 100644 drivers/mailbox/hi3660-mailbox.c
>
> diff --git a/drivers/mailbox/Kconfig b/drivers/mailbox/Kconfig
> index c5731e5..4b5d6e9 100644
> --- a/drivers/mailbox/Kconfig
> +++ b/drivers/mailbox/Kconfig
> @@ -108,6 +108,14 @@ config TI_MESSAGE_MANAGER
>           multiple processors within the SoC. Select this driver if your
>           platform has support for the hardware block.
>
> +config HI3660_MBOX
> +       tristate "Hi3660 Mailbox"
> +       depends on ARCH_HISI && OF
> +       help
> +         An implementation of the hi3660 mailbox. It is used to send message
> +         between application processors and other processors/MCU/DSP. Select
> +         Y here if you want to use Hi3660 mailbox controller.
> +
>  config HI6220_MBOX
>         tristate "Hi6220 Mailbox"
>         depends on ARCH_HISI
> diff --git a/drivers/mailbox/Makefile b/drivers/mailbox/Makefile
> index d54e412..7d1bd51 100644
> --- a/drivers/mailbox/Makefile
> +++ b/drivers/mailbox/Makefile
> @@ -26,6 +26,8 @@ obj-$(CONFIG_TI_MESSAGE_MANAGER) += ti-msgmgr.o
>
>  obj-$(CONFIG_XGENE_SLIMPRO_MBOX) += mailbox-xgene-slimpro.o
>
> +obj-$(CONFIG_HI3660_MBOX)      += hi3660-mailbox.o
> +
>  obj-$(CONFIG_HI6220_MBOX)      += hi6220-mailbox.o
>
>  obj-$(CONFIG_BCM_PDC_MBOX)     += bcm-pdc-mailbox.o
> diff --git a/drivers/mailbox/hi3660-mailbox.c b/drivers/mailbox/hi3660-mailbox.c
> new file mode 100644
> index 0000000..ba80834
> --- /dev/null
> +++ b/drivers/mailbox/hi3660-mailbox.c
> @@ -0,0 +1,322 @@
> +/*
> + * Hisilicon's Hi3660 mailbox controller driver
> + *
> + * Copyright (c) 2017 Hisilicon Limited.
> + * Copyright (c) 2017 Linaro Limited.
> + *
> + * Author: Leo Yan <leo.yan@xxxxxxxxxx>
> + *
> + * This program is free software: you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation, version 2 of the License.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
>
We now use SPDX licence

> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/err.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/mailbox_controller.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +
> +#include "mailbox.h"
> +
> +#define MBOX_CHAN_MAX                  32
> +
> +#define MBOX_RX                                (0x0)
> +#define MBOX_TX                                (0x1)
> +
> +#define MBOX_BASE(mbox, ch)            ((mbox)->base + ((ch) * 0x40))
> +#define MBOX_SRC_REG                   (0x00)
> +#define MBOX_DST_REG                   (0x04)
> +#define MBOX_DCLR_REG                  (0x08)
> +#define MBOX_DSTAT_REG                 (0x0c)
> +#define MBOX_MODE_REG                  (0x10)
> +#define MBOX_IMASK_REG                 (0x14)
> +#define MBOX_ICLR_REG                  (0x18)
> +#define MBOX_SEND_REG                  (0x1c)
> +#define MBOX_DATA_REG                  (0x20)
> +
> +#define MBOX_IPC_LOCK_REG              (0xa00)
> +#define MBOX_IPC_UNLOCK                        (0x1acce551)
> +
> +#define MBOX_AUTOMATIC_ACK             (1)
> +
Please, no brackets around numbers.

> +#define MBOX_STATE_IDLE                        BIT(4)
> +#define MBOX_STATE_ACK                 BIT(7)
> +
> +#define MBOX_MSG_LEN                   8
> +
> +/**
> + * Hi3660 mailbox channel device data
> + *
> + * A channel can be used for TX or RX, it can trigger remote
> + * processor interrupt to notify remote processor and can receive
> + * interrupt if has incoming message.
> + *
> + * @dst_irq:   Interrupt vector for remote processor
> + * @ack_irq:   Interrupt vector for local processor
> + */
> +struct hi3660_mbox_dev {
>
Better than dev, maybe hi3660_chan_info ?

> +       unsigned int dst_irq;
> +       unsigned int ack_irq;
> +};
> +
> +/**
> + * Hi3660 mailbox controller data
> + *
> + * Mailbox controller includes 32 channels and can allocate
> + * channel for message transferring.
> + *
> + * @dev:       Device to which it is attached
> + * @base:      Base address of the register mapping region
> + * @chan:      Representation of channels in mailbox controller
> + * @mdev:      Representation of channel device data
> + * @controller:        Representation of a communication channel controller
> + */
> +struct hi3660_mbox {
> +       struct device *dev;
> +       void __iomem *base;
> +       struct mbox_chan chan[MBOX_CHAN_MAX];
> +       struct hi3660_mbox_dev mdev[MBOX_CHAN_MAX];
>
Maybe mchan, instead of mdev.

> +       struct mbox_controller controller;
> +};
> +
> +static inline struct hi3660_mbox *to_hi3660_mbox(struct mbox_controller *mbox)
> +{
> +       return container_of(mbox, struct hi3660_mbox, controller);
> +}
> +
> +static int hi3660_mbox_check_state(struct mbox_chan *chan)
> +{
> +       unsigned long ch = (unsigned long)chan->con_priv;
> +       struct hi3660_mbox *mbox = to_hi3660_mbox(chan->mbox);
> +       struct hi3660_mbox_dev *mdev = &mbox->mdev[ch];
> +       void __iomem *base = MBOX_BASE(mbox, ch);
> +       unsigned long val;
> +       unsigned int state, ret;
> +
> +       /* Mailbox is idle so directly bail out */
> +       state = readl_relaxed(base + MBOX_MODE_REG);
> +       if (state & MBOX_STATE_IDLE)
> +               return 0;
> +
> +       /* Wait for acknowledge from remote */
> +       ret = readx_poll_timeout_atomic(readl_relaxed, base + MBOX_MODE_REG,
> +                       val, (val & MBOX_STATE_ACK), 1000, 300000);
> +       if (ret) {
> +               dev_err(mbox->dev, "%s: timeout for receiving ack\n", __func__);
> +               return ret;
> +       }
> +
> +       /* Ensure channel is released */
> +       writel_relaxed(0xffffffff, base + MBOX_IMASK_REG);
> +       writel_relaxed(BIT(mdev->ack_irq), base + MBOX_SRC_REG);
> +
> +       return 0;
> +}
> +
> +static int hi3660_mbox_unlock(struct mbox_chan *chan)
> +{
> +       struct hi3660_mbox *mbox = to_hi3660_mbox(chan->mbox);
> +       unsigned int val, retry = 3;
> +
> +       do {
> +               writel_relaxed(MBOX_IPC_UNLOCK, mbox->base + MBOX_IPC_LOCK_REG);
> +
> +               val = readl_relaxed(mbox->base + MBOX_IPC_LOCK_REG);
> +               if (!val)
> +                       break;
> +
> +               udelay(10);
> +       } while (retry--);
> +
> +       return (!val) ? 0 : -ETIMEDOUT;
> +}
> +
> +static int hi3660_mbox_acquire_channel(struct mbox_chan *chan)
> +{
> +       unsigned long ch = (unsigned long)chan->con_priv;
> +       struct hi3660_mbox *mbox = to_hi3660_mbox(chan->mbox);
> +       struct hi3660_mbox_dev *mdev = &mbox->mdev[ch];
> +       void __iomem *base = MBOX_BASE(mbox, ch);
> +       unsigned int val, retry;
> +
> +       for (retry = 10; retry; retry--) {
> +               /* Check if channel has been acquired */
> +               if (readl_relaxed(base + MBOX_MODE_REG) & MBOX_STATE_IDLE) {
> +                       writel_relaxed(BIT(mdev->ack_irq), base + MBOX_SRC_REG);
> +                       val = readl_relaxed(base + MBOX_SRC_REG);
> +                       if (val & BIT(mdev->ack_irq))
> +                               break;
> +               }
> +       }
> +
> +       return retry ? 0 : -ETIMEDOUT;
> +}
> +
> +static int hi3660_mbox_send(struct mbox_chan *chan, u32 *msg)
> +{
> +       unsigned long ch = (unsigned long)chan->con_priv;
> +       struct hi3660_mbox *mbox = to_hi3660_mbox(chan->mbox);
> +       struct hi3660_mbox_dev *mdev = &mbox->mdev[ch];
> +       void __iomem *base = MBOX_BASE(mbox, ch);
> +       unsigned int i;
> +
> +       /* Clear mask for destination interrupt */
> +       writel_relaxed(~BIT(mdev->dst_irq), base + MBOX_IMASK_REG);
> +
> +       /* Config destination for interrupt vector */
> +       writel_relaxed(BIT(mdev->dst_irq), base + MBOX_DST_REG);
> +
> +       /* Automatic acknowledge mode */
> +       writel_relaxed(MBOX_AUTOMATIC_ACK, base + MBOX_MODE_REG);
> +
> +       /* Fill message data */
> +       for (i = 0; i < MBOX_MSG_LEN; i++)
> +               writel_relaxed(msg[i], base + MBOX_DATA_REG + i * 4);
> +
> +       /* Trigger data transferring */
> +       writel_relaxed(BIT(mdev->ack_irq), base + MBOX_SEND_REG);
> +       return 0;
> +}
> +
> +static int hi3660_mbox_send_data(struct mbox_chan *chan, void *msg)
> +{
> +       struct hi3660_mbox *mbox = to_hi3660_mbox(chan->mbox);
> +       int err;
> +
> +       err = hi3660_mbox_check_state(chan);
> +       if (err) {
> +               dev_err(mbox->dev, "checking state failed\n");
> +               return err;
> +       }
> +
> +       err = hi3660_mbox_unlock(chan);
> +       if (err) {
> +               dev_err(mbox->dev, "unlocking mailbox failed\n");
> +               return err;
> +       }
> +
> +       err = hi3660_mbox_acquire_channel(chan);
> +       if (err) {
> +               dev_err(mbox->dev, "acquiring channel failed\n");
> +               return err;
> +       }
> +
Please remember .send_data() is called with irqs disabled spinlock
All these polling functions hurt. Please move the above three checks
in last_tx_done()

Thanks
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux