[PATCH] arm64: dts: allwinner: a64: bananapi-m64: Add LED device node

[Chen-Yu Tsai <wens@xxxxxxxx>]

The Bananapi-M64 has 3 LEDS in red, green, and blue. These are toggled
via GPIO lines, which drive transistors that control current across the
LEDS. The red LED is by default on, via an additional pull-up on the
control line. We consider this means that it is a power indicator.
So we set the "default-on" property for it.

The pingroups the GPIO lines belong to require external regulators be
enabled to be able to drive the GPIO high. These regulators also have
other purposes. However the pin controller does not have bindings for
regulators. Here we just set them to always-on.

Signed-off-by: Chen-Yu Tsai <wens@xxxxxxxx>
---
 .../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 36 ++++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index 4a8d3f83a36e..a6975670cd1c 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -60,6 +60,26 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	leds {
+		compatible = "gpio-leds";
+
+		pwr-led {
+			label = "bananapi-m64:red:pwr";
+			gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+			default-state = "on";
+		};
+
+		green {
+			label = "bananapi-m64:green:user";
+			gpios = <&pio 4 14 GPIO_ACTIVE_HIGH>; /* PE14 */
+		};
+
+		blue {
+			label = "bananapi-m64:blue:user";
+			gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
+		};
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
@@ -153,6 +173,17 @@
 
 #include "axp803.dtsi"
 
+&reg_aldo1 {
+	/*
+	 * This regulator also drives the PE pingroup GPIOs,
+	 * which also controls two LEDs.
+	 */
+	regulator-always-on;
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "afvcc-csi";
+};
+
 &reg_aldo2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1800000>;
@@ -168,6 +199,11 @@
 };
 
 &reg_dc1sw {
+	/*
+	 * This regulator also indirectly drives the PD pingroup GPIOs,
+	 * which also controls the power LED.
+	 */
+	regulator-always-on;
 	regulator-name = "vcc-phy";
 };
 
-- 
2.15.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html