This adds device tree bindings for the Ilitek ILI9322
320x240 TFT panel driver.
Cc: David Lechner <david@xxxxxxxxxxxxxx>
Cc: Stefano Babic <sbabic@xxxxxxx>
Cc: Ben Dooks <ben.dooks@xxxxxxxxxxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
ChangeLog v1->v2:
- Add explicit requirement to specify the system type so the
driver can look up the display configuration from the
compatible string.
- Dropped all display-specific configuration data I could
in favor of open coding it all in a per-system config struct
in the driver.
- Now only regulators and GPIO lines remain as DT resources.
---
.../bindings/display/panel/ilitek,ili9322.txt | 49 ++++++++++++++++++++++
1 file changed, 49 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt
diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt
new file mode 100644
index 000000000000..3d5ce6ad6ec7
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt
@@ -0,0 +1,49 @@
+Ilitek ILI9322 TFT panel driver with SPI control bus
+
+This is a driver for 320x240 TFT panels, accepting a variety of input
+streams that get adapted and scaled to the panel. The panel output has
+960 TFT source driver pins and 240 TFT gate driver pins, VCOM, VCOML and
+VCOMH outputs.
+
+Required properties:
+ - compatible: "dlink,dir-685-panel", "ilitek,ili9322"
+ (full system-specific compatible is always required to look up configuration)
+ - reg: address of the panel on the SPI bus
+
+Optional properties:
+ - vcc-supply: core voltage supply, see regulator/regulator.txt
+ - iovcc-supply: voltage supply for the interface input/output signals,
+ see regulator/regulator.txt
+ - vci-supply: voltage supply for analog parts, see regulator/regulator.txt
+ - reset-gpios: a GPIO spec for the reset pin, see gpio/gpio.txt
+
+ The following optional properties only apply to RGB and YUV input modes and
+ can be omitted for BT.656 input modes:
+
+ - pixelclk-active: see display/panel/display-timing.txt
+ - de-active: see display/panel/display-timing.txt
+ - hsync-active: see display/panel/display-timing.txt
+ - vsync-active: see display/panel/display-timing.txt
+
+The panel must obey the rules for a SPI slave device as specified in
+spi/spi-bus.txt
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in
+media/video-interfaces.txt. This node should describe panel's video bus.
+
+Example:
+
+panel: display@0 {
+ compatible = "dlink,dir-685-panel", "ilitek,ili9322";
+ reg = <0>;
+ vcc-supply = <&vdisp>;
+ iovcc-supply = <&vdisp>;
+ vci-supply = <&vdisp>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+};
--
2.14.3
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
