Hi Geert-san, Vladimir-san,
> From: Vladimir Barinov, Sent: Saturday, October 7, 2017 2:29 AM
>
> Hi Geert,
>
> On 06.10.2017 10:15, Geert Uytterhoeven wrote:
> > Hi Vladimir,
> >
> > CC Shimoda-san
> >
> > On Fri, Oct 6, 2017 at 4:38 AM, Vladimir Barinov
> > <vladimir.barinov@xxxxxxxxxxxxxxxxxx> wrote:
> >> On 20.09.2017 15:59, Geert Uytterhoeven wrote:
> >>> On Thu, Sep 7, 2017 at 12:36 AM, Vladimir Barinov
> >>> <vladimir.barinov@xxxxxxxxxxxxxxxxxx> wrote:
> >>>> This supports USB2 PHY channel #0 on ULCB Kingfisher board
> >>>>
> >>>> Signed-off-by: Vladimir Barinov <vladimir.barinov@xxxxxxxxxxxxxxxxxx>
> >>> Reviewed-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
> >>>
> >>>> index ca8de1a..0854600 100644
> >>>> --- a/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi
> >>>> +++ b/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi
> >>>> @@ -60,6 +60,11 @@
> >>>> groups = "scif1_data_b";
> >>>> function = "scif1";
> >>>> };
> >>>> +
> >>>> + usb0_pins: usb0 {
> >>>> + groups = "usb0";
> >>>> + function = "usb0";
> >>>> + };
> >>>> };
> >>>>
> >>>> &scif1 {
> >>>> @@ -68,3 +73,10 @@
> >>>>
> >>>> status = "okay";
> >>>> };
> >>>> +
> >>>> +&usb2_phy0 {
> >>>> + pinctrl-0 = <&usb0_pins>;
> >>>> + pinctrl-names = "default";
> >>>> +
> >>> Don't you need
> >>>
> >>> vbus-supply = <&vbus0_usb2>;
> >>>
> >>> with vbus0_usb2 a fixed regulator controlled by GPIO P11 (OTG_EXTLPn) from
> >>> GPIO expander U11 (TCA9539)?
> >>> May be optional, though. salvator-common.dtsi has it.
> >> Yes, I need this gpio.
> >> I need both OTG_EXTLPn and OTG_OFFVBUSn from the same gpio expander.
> >>
> >> I've been considering to use either vbus-supply + gpio hog or use gpio hog
> >> for both of them for consistency.
> >> What do you think about this?
> > For OTG_EXTLPn you don't really need a hog, as it will be controlled by the
> > USB driver/subsystem, like on Salvator-X(S), right?
> Agreed.
> >
> > For OTG_OFFVBUSn, which is (optionally) driven from USB0_PWEN on
> > Salvator-X(S) I don't know if you need a GPIO hog or not. I have to defer your
> > question to Shimoda-san.
I'm sorry for the delayed response.
I think OTG_OFFVBUSn should be low level to avoid conflict 5V supply from U13's OUT pins.
> This pin should be tied permanently low to disable internal MAX3355
> internal VBUS charge pump.
I agree.
> Hence probably gpio hog is enough for OTG_OFFVBUSn.
I'm afraid but I don't understand this "gpio hog" means.
> KF has dedicated VBUS power supply controlled by USB0_PWEN.
I agree.
I don’t write any documentations though, but I assumed SW15 is pin 3 side
to use MAX3355's charge pump. So, I added "vbus-supply" to disable SHDN# of MAX3355.
But, we can also use U13 for power supply on the Salvator-X[S] without "vbus-supply".
Best regards,
Yoshihiro Shimoda
>
> --
> Regards,
> Vladimir
��.n��������+%������w��{.n����z�{��ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f
