On Fri, Sep 22, 2017 at 03:24:11PM -0700, Tim Harvey wrote:
> Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
You need a commit msg. Otherwise, maintainers get publicly shamed.
> ---
> .../devicetree/bindings/media/i2c/tda1997x.txt | 159 +++++++++++++++++++++
> 1 file changed, 159 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
> new file mode 100644
> index 0000000..8330733
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
> @@ -0,0 +1,159 @@
> +Device-Tree bindings for the NXP TDA1997x HDMI receiver
> +
> +The TDA19971/73 are HDMI video receivers.
> +
> +The TDA19971 Video port output pins can be used as follows:
> + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4]
> + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4]
> + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4]
> + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2]
> + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0]
> + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles)
> + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles)
> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
> +
> +The TDA19973 Video port output pins can be used as follows:
> + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0]
> + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0]
> + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0]
> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
> +
> +The Video port output pins are mapped via 4-bit 'pin groups' allowing
> +for a variety fo connection possibilities including swapping pin order within
> +pin groups. The video_portcfg device-tree property consists of register mapping
> +pairs which map a chip-specific VP output register to a 4-bit pin group. If
> +the pin group needs to be bit-swapped you can use the *_S pin-group defines.
> +
> +Required Properties:
> + - compatible :
> + - "nxp,tda19971" for the TDA19971
> + - "nxp,tda19973" for the TDA19973
> + - reg : I2C slave address
> + - interrupts : The interrupt number
> + - DOVDD-supply : Digital I/O supply
> + - DVDD-supply : Digital Core supply
> + - AVDD-supply : Analog supply
> + - vidout_portcfg : array of pairs mapping VP output pins to pin groups
Needs a vendor prefix and don't use '_'.
> +
> +Optional Properties:
> + - max-pixel-rate : Maximum pixel rate supported by the SoC (MP/sec)
> + - audio-port : parameters defining audio output port connection
That description is meaningless to me.
> +
> +Optional Endpoint Properties:
> + The following three properties are defined in video-interfaces.txt and
> + are valid for source endpoints only:
> + - hsync-active: Horizontal synchronization polarity. Defaults to active high.
> + - vsync-active: Vertical synchronization polarity. Defaults to active high.
> + - data-active: Data polarity. Defaults to active high.
> +
> +The Audio output port consists of A_CLK, A_WS, AP0, AP1, AP2, and AP3 pins
> +and can support up to 8-chanenl audio using the following audio bus DAI formats:
> + - I2S16
> + - I2S32
> + - SPDIF
> + - OBA (One-Bit-Audio)
> + - I2S16_HBR_STRAIGHT (High Bitrate straight through)
> + - I2S16_HBR_DEMUX (High Bitrate demuxed)
> + - I2S32_HBR_DEMUX (High Bitrate demuxed)
> + - DST (Direct Stream Transfer)
This either should be a standard, common property or not be in DT.
Practically every system is going to have at least one end of the
connection that is configurable. The kernel should be able to get lists
of supported modes and pick one.
> +
> +Audio samples can be output in either SPDIF or I2S bus formats.
> +In I2S mode, the TDF1997X is the master with 16bit or 32bit words.
> +The audio port output is configured by three parameters: DAI format, layout
> +and clock scaler.
> +
> +Each DAI format has two pin layouts shown by the following table:
> + | SPDIF | SPDIF | I2S | I2S | HBR demux
> + | Layout0 | Layout1 | Layout0 | Layout1 | SPDIF | I2S
> + ------+---------+---------+---------+---------+------------+------------
> + A_WS | WS | WS | WS | WS | WS | WS
> + AP3 | | SPDIF3 | | SD3 | SPDIF[x+3] | SD[x+3]
> + AP2 | | SPDIF2 | | SD2 | SPDIF[x+2] | SD[x+2]
> + AP1 | | SPDIF1 | | SD1 | SPDIF[x+1] | SD[x+1]
> + AP0 | SPDIF | SPDIF0 | SD | SD0 | SPDIF[x] | SD[x]
> + A_CLK | (32*Fs) | (32*Fs) |(32*Fs) | (32*Fs) | (32*Fs) | (32*Fs)
> + | (64*Fs) | (64*Fs) |(64*Fs) | (64*Fs) | (64*Fs) | (64*Fs)
> +
> +Freq(Sysclk) = 2*freq(Aclk)
> +
> +Examples:
> + - VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422
> + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
> + hdmi_receiver@48 {
s/_/-/
> + compatible = "nxp,tda19971";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_tda1997x>;
> + reg = <0x48>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> + DOVDD-supply = <®_3p3v>;
> + AVDD-supply = <®_1p8v>;
> + DVDD-supply = <®_1p8v>;
> + /* audio output format */
> + audio-port = < TDA1997X_I2S16
> + TDA1997X_LAYOUT0
> + TDA1997X_ACLK_128FS >;
> + /*
> + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
> + * and Y[11:4] across 16bits in the same pixclk cycle.
> + */
> + vidout_portcfg =
> + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
> + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
> + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
> + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
> + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
> + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
> + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
> + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
> + max-pixel-rate = <180>; /* IMX6 CSI max pixel rate 180MP/sec */
That's a constraint that belongs in the i.MX CSI node or driver.
> +
> + port@0 {
> + reg = <0>;
> + };
> + port@1 {
You need to describe how many ports and what they are.
> + reg = <1>;
> + hdmi_in: endpoint {
> + remote-endpoint = <&ccdc_in>;
> + };
> + };
> + };
> + - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
> + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
Do you really need 2 examples? It should be possible to figure out other
configurations with better descriptions above.
> + hdmi_receiver@48 {
> + compatible = "nxp,tda19971";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_tda1997x>;
> + reg = <0x48>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> + DOVDD-supply = <®_3p3v>;
> + AVDD-supply = <®_1p8v>;
> + DVDD-supply = <®_1p8v>;
> + /* audio output format */
> + #sound-dai-cells = <0>;
> + audio-port = < TDA1997X_I2S16
> + TDA1997X_LAYOUT0
> + TDA1997X_ACLK_128FS >;
> + /*
> + * The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over
> + * 2 pixclk cycles.
> + */
> + vidout_portcfg =
> + /* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
> + < TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >,
> + /* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
> + < TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >,
> + max-pixel-rate = <180>; /* IMX6 CSI max pixel rate 180MP/sec */
> +
> + port@0 {
> + reg = <0>;
> + };
> + port@1 {
> + reg = <1>;
> + hdmi_in: endpoint {
> + remote-endpoint = <&ccdc_in>;
> + };
> + };
> + };
> +
> --
> 2.7.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
