This is the successor to Carlo Caione's "Add support for Amlogic Meson
MMC driver" series (v5) from [0].
This new driver is for the "SDIO" controller found in Amlogic Meson6,
Meson8 and Meson8b SoCs and supports an internal mux to allow connecting
three cards to it.
changes since RFC v1 at [1]:
- added COMMON_CLK dependency as reported by the kbuild test robot
- use of_platform_device_{create,destroy} instead of open-coding it's
logic
- moved struct device (which was an array) from meson_mx_mmc_host to
the corresponding meson_mx_mmc_slot
- use struct mmc_command's busy_timeout instead of hard-coding the
timeout values in meson_mx_mmc_start_cmd()
- don't use arrays with only one element for the clock parents in
meson_mx_mmc_register_clks()
- removed the wrapper functions meson_mx_mmc_readl() meson_mx_mmc_writel()
- allow setting the MMC clock to 0 for UHS speed mode (the actual
hardware clock cannot be gated as far as I know, so instead the
lowest supported rate is chosen)
- remove unused #include <linux/init.h>
- add MMC_CAP_ERASE
- removed multiple slot support after discussing this with Ulf
(this is a feature that needs to be part of the MMC core before drivers
can use it)
- removed SDIO interrupt support (as I currently don't have a way to
test it)
- merge meson_mx_mmc_apply_ios into meson_mx_mmc_set_ios (as that's
the only place where it's needed after removing multiple slot support)
- updated the commit message of the driver patch to indicate the
difference between the meson-mx-sdio.c and meson-gx.c (and the "still
missing SDHC") driver
- NOTE: I did not add Rob's ACK on the dt-bindings patch because I
introduced the "mmc-slot" compatible for the child nodes as suggested
by Ulf (and I want confirmation from the DT maintainers that I did this
correctly)
(notable) changes since Carlo's latest from [0] version are:
- renamed the driver to meson-mx-sdio (Amlogic's reference kernel calls
the driver "aml_sdio" as there is a second MMC controller in these SoCs
which they call the "SDHC controller"). do the same with our driver to
avoid confusion once we add support for the second controller (which uses
a completely different register layout)
- add support for the internal "mux" in this MMC controller (which allows
connecting up to three devices to the the controller - at the cost of
performance though since the controller can only process one request at
a time). The driver registers a new device for each sub-node, which is
then fed into the MMC framework to allow per-slot configuration using
devicetree (see the example in the documentation)
- use the common clock framework internally for managing the MMC clock
(there is a fixed-factor clock in the controller which takes clk81 as
input and divides it's clock by two and a divider clock which takes
the result from the fixed-factor clock as input)
- support the regulators provided by the MMC framework
- support for GPIO-based card-detection and read-only-detection through
the MMC framework
- use of the <linux/bitfield.h> FIELD_PREP and FIELD_GET macros where it
make sense (and thus the code easier to read)
- re-worked locking (based on the locking in dw_mmc as that also provides
multiple "MMC slots")
tests done so far (use-cases which involve two cards were done only with
RFC v1):
- reading an OLD 256MiB SD card (which uses only a 1-bit bus) works fine
(sha1sum of the whole device matches with what I get on my PC's
card-reader)
- reading a somewhat more modern class 10 SD card and putting Arch Linux
ARM on it (and using that as root file system)
- it successfully detects the RTL8723BS SDIO wifi chip in my device (even
if the SD card is also enabled)
- reading a 128MiB file from the SD card while scanning wifi networks on
the RTL8723BS card does not seem to result in any corruption (sha1sum
of the read file seems to match)
- read speed of my class 10 SD card: ~15MiB/s
- (unfortunately I could NOT test downloading a file over wifi to the SD
card because the RTL8723BS driver refuses to see any wifi networks, but
that might be a problem on the RTL8723BS driver side since I don't get
any error and the driver has just landed a few weeks ago in staging)
[0] http://lists.infradead.org/pipermail/linux-arm-kernel/2016-February/412136.html
[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-May/003466.html
Carlo Caione (2):
dt-bindings: mmc: Document the Amlogic Meson8 and Meson8b SDIO
bindings
mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b
SoCs
.../bindings/mmc/amlogic,meson-mx-sdio.txt | 52 ++
drivers/mmc/host/Kconfig | 13 +
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/meson-mx-sdio.c | 795 +++++++++++++++++++++
4 files changed, 861 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdio.txt
create mode 100644 drivers/mmc/host/meson-mx-sdio.c
--
2.14.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
