Hello Yong,
Thank you for these drivers!
I tested it with an OV5640 camera on an Nanopi M1 plus (Allwinner H3)
and I noticed that I got a frame correctly displayed only on a half of
the frame's size.
It is related to your "sun6i_csi_set_window" function (see
below).
> Allwinner V3s SoC have two CSI module. CSI0 is used for MIPI interface
> and CSI1 is used for parallel interface. This is not documented in
> datasheet but by testing and guess.
>
> This patch implement a v4l2 framework driver for it.
>
> Currently, the driver only support the parallel interface. MIPI-CSI2,
> ISP's support are not included in this patch.
>
> Signed-off-by: Yong Deng <yong.deng@xxxxxxxxxxxx>
> ---
> drivers/media/platform/Kconfig | 1 +
> drivers/media/platform/Makefile | 2 +
> drivers/media/platform/sun6i-csi/Kconfig | 9 +
> drivers/media/platform/sun6i-csi/Makefile | 3 +
> drivers/media/platform/sun6i-csi/sun6i_csi.c | 545
> +++++++++++++++ drivers/media/platform/sun6i-csi/sun6i_csi.h |
> 203 ++++++ drivers/media/platform/sun6i-csi/sun6i_csi_v3s.c | 827
> +++++++++++++++++++++++
> drivers/media/platform/sun6i-csi/sun6i_csi_v3s.h | 206 ++++++
> drivers/media/platform/sun6i-csi/sun6i_video.c | 663
> ++++++++++++++++++ drivers/media/platform/sun6i-csi/sun6i_video.h
> | 61 ++ 10 files changed, 2520 insertions(+) create mode 100644
> drivers/media/platform/sun6i-csi/Kconfig create mode 100644
> drivers/media/platform/sun6i-csi/Makefile create mode 100644
> drivers/media/platform/sun6i-csi/sun6i_csi.c create mode 100644
> drivers/media/platform/sun6i-csi/sun6i_csi.h create mode 100644
> drivers/media/platform/sun6i-csi/sun6i_csi_v3s.c create mode 100644
> drivers/media/platform/sun6i-csi/sun6i_csi_v3s.h create mode 100644
> drivers/media/platform/sun6i-csi/sun6i_video.c create mode 100644
> drivers/media/platform/sun6i-csi/sun6i_video.h
>
> diff --git a/drivers/media/platform/Kconfig
> b/drivers/media/platform/Kconfig index 0c741d1..8371a87 100644
> --- a/drivers/media/platform/Kconfig
> +++ b/drivers/media/platform/Kconfig
> @@ -143,6 +143,7 @@ source "drivers/media/platform/am437x/Kconfig"
> source "drivers/media/platform/xilinx/Kconfig"
> source "drivers/media/platform/rcar-vin/Kconfig"
> source "drivers/media/platform/atmel/Kconfig"
> +source "drivers/media/platform/sun6i-csi/Kconfig"
>
<snip>
> +static void sun6i_csi_set_format(struct sun6i_csi_dev *sdev)
> +{
> + struct sun6i_csi *csi = &sdev->csi;
> + u32 cfg;
> + u32 val;
> +
> + regmap_read(sdev->regmap, CSI_CH_CFG_REG, &cfg);
> +
> + cfg &= ~(CSI_CH_CFG_INPUT_FMT_MASK |
> + CSI_CH_CFG_OUTPUT_FMT_MASK | CSI_CH_CFG_VFLIP_EN |
> + CSI_CH_CFG_HFLIP_EN | CSI_CH_CFG_FIELD_SEL_MASK |
> + CSI_CH_CFG_INPUT_SEQ_MASK);
> +
> + val = get_csi_input_format(csi->config.code,
> csi->config.pixelformat);
> + cfg |= CSI_CH_CFG_INPUT_FMT(val);
> +
> + val = get_csi_output_format(csi->config.code,
> csi->config.field);
> + cfg |= CSI_CH_CFG_OUTPUT_FMT(val);
> +
> + val = get_csi_input_seq(csi->config.code,
> csi->config.pixelformat);
> + cfg |= CSI_CH_CFG_INPUT_SEQ(val);
> +
> + if (csi->config.field == V4L2_FIELD_TOP)
> + cfg |= CSI_CH_CFG_FIELD_SEL_FIELD0;
> + else if (csi->config.field == V4L2_FIELD_BOTTOM)
> + cfg |= CSI_CH_CFG_FIELD_SEL_FIELD1;
> + else
> + cfg |= CSI_CH_CFG_FIELD_SEL_BOTH;
> +
> + regmap_write(sdev->regmap, CSI_CH_CFG_REG, cfg);
> +}
> +
> +static void sun6i_csi_set_window(struct sun6i_csi_dev *sdev)
> +{
> + struct sun6i_csi_config *config = &sdev->csi.config;
> + u32 bytesperline_y;
> + u32 bytesperline_c;
> + int *planar_offset = sdev->planar_offset;
> +
> + regmap_write(sdev->regmap, CSI_CH_HSIZE_REG,
> + CSI_CH_HSIZE_HOR_LEN(config->width) |
> + CSI_CH_HSIZE_HOR_START(0));
> + regmap_write(sdev->regmap, CSI_CH_VSIZE_REG,
> + CSI_CH_VSIZE_VER_LEN(config->height) |
> + CSI_CH_VSIZE_VER_START(0));
In my case, the HOR_LEN and VER_LEN were not correctly configured.
They were configured to width and height (640 * 480) but as I was
using a YUYV format, the pixel's size is 2 bytes so the
horizontal/vertical lines' lengths were divided by 2.
Currently, I fixed that by getting the number of bytes per pixel with
"v4l2_pixformat_get_bpp()":
+ int bytes_pixel;
+
+ bytes_pixel = v4l2_pixformat_get_bpp(config->pixelformat) / 8;
regmap_write(sdev->regmap, CSI_CH_HSIZE_REG,
- CSI_CH_HSIZE_HOR_LEN(config->width) |
+ CSI_CH_HSIZE_HOR_LEN(config->width * bytes_pixel) |
CSI_CH_HSIZE_HOR_START(0));
regmap_write(sdev->regmap, CSI_CH_VSIZE_REG,
- CSI_CH_VSIZE_VER_LEN(config->height) |
+ CSI_CH_VSIZE_VER_LEN(config->height * bytes_pixel)
| CSI_CH_VSIZE_VER_START(0));
There is certainly a nicer way to handle that.
> +
> + planar_offset[0] = 0;
> + switch(config->pixelformat) {
> + case V4L2_PIX_FMT_HM12:
> + case V4L2_PIX_FMT_NV12:
> + case V4L2_PIX_FMT_NV21:
> + case V4L2_PIX_FMT_NV16:
> + case V4L2_PIX_FMT_NV61:
> + bytesperline_y = config->width;
> + bytesperline_c = config->width;
> + planar_offset[1] = bytesperline_y * config->height;
> + planar_offset[2] = -1;
> + break;
> + case V4L2_PIX_FMT_YUV420:
> + case V4L2_PIX_FMT_YVU420:
> + bytesperline_y = config->width;
> + bytesperline_c = config->width / 2;
> + planar_offset[1] = bytesperline_y * config->height;
> + planar_offset[2] = planar_offset[1] +
> + bytesperline_c * config->height / 2;
> + break;
> + case V4L2_PIX_FMT_YUV422P:
> + bytesperline_y = config->width;
> + bytesperline_c = config->width / 2;
> + planar_offset[1] = bytesperline_y * config->height;
> + planar_offset[2] = planar_offset[1] +
> + bytesperline_c * config->height;
> + break;
> + default: /* raw */
> + bytesperline_y =
> (v4l2_pixformat_get_bpp(config->pixelformat) *
> + config->width) / 8;
> + bytesperline_c = 0;
> + planar_offset[1] = -1;
> + planar_offset[2] = -1;
> + break;
> + }
> +
> + regmap_write(sdev->regmap, CSI_CH_BUF_LEN_REG,
> + CSI_CH_BUF_LEN_BUF_LEN_C(bytesperline_c) |
> + CSI_CH_BUF_LEN_BUF_LEN_Y(bytesperline_y));
> +}
> +
> +static int get_supported_pixformats(struct sun6i_csi *csi,
> + const u32 **pixformats)
> +{
> + if (pixformats != NULL)
> + *pixformats = supported_pixformats;
> +
> + return ARRAY_SIZE(supported_pixformats);
> +}
> +
> +static bool is_format_support(struct sun6i_csi *csi, u32 pixformat,
> + u32 mbus_code)
> +{
> + struct sun6i_csi_dev *sdev = sun6i_csi_to_dev(csi);
> +
> + return __is_format_support(sdev, pixformat, mbus_code);
> +}
> +
> +static int set_power(struct sun6i_csi *csi, bool enable)
> +{
> + struct sun6i_csi_dev *sdev = sun6i_csi_to_dev(csi);
> + struct regmap *regmap = sdev->regmap;
> + int ret;
> +
> + if (!enable) {
> + regmap_update_bits(regmap, CSI_EN_REG,
> CSI_EN_CSI_EN, 0); +
> + clk_disable_unprepare(sdev->clk_ram);
> + clk_disable_unprepare(sdev->clk_mod);
> + clk_disable_unprepare(sdev->clk_ahb);
> + reset_control_assert(sdev->rstc_ahb);
> + return 0;
> + }
> +
> + ret = clk_prepare_enable(sdev->clk_ahb);
> + if (ret) {
> + dev_err(sdev->dev, "Enable ahb clk err %d\n", ret);
> + return ret;
> + }
> +
> + ret = clk_prepare_enable(sdev->clk_mod);
> + if (ret) {
> + dev_err(sdev->dev, "Enable csi clk err %d\n", ret);
> + return ret;
> + }
> +
> + ret = clk_prepare_enable(sdev->clk_ram);
> + if (ret) {
> + dev_err(sdev->dev, "Enable clk_dram_csi clk err
> %d\n", ret);
> + return ret;
> + }
> +
> + if (!IS_ERR_OR_NULL(sdev->rstc_ahb)) {
> + ret = reset_control_deassert(sdev->rstc_ahb);
> + if (ret) {
> + dev_err(sdev->dev, "reset err %d\n", ret);
> + return ret;
> + }
> + }
> +
> + regmap_update_bits(regmap, CSI_EN_REG, CSI_EN_CSI_EN,
> CSI_EN_CSI_EN); +
> + return 0;
> +}
<snip>
Thank you in advance!
Best regards,
--
Mylène Josserand, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
