Re: [PATCH v3 2/2] dt-bindings: drm/bridge: Document Cadence DSI bridge bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 01.09.2017 09:06, Boris Brezillon wrote:
> Hi Andrzej,
>
> On Fri, 01 Sep 2017 08:28:13 +0200
> Andrzej Hajda <a.hajda@xxxxxxxxxxx> wrote:
>
>> On 31.08.2017 17:55, Boris Brezillon wrote:
>>> Document the bindings used for the Cadence DSI bridge.
>>>
>>> Signed-off-by: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx>
>>> ---
>>> Changes in v3:
>>> - Fix clock names in the example
>>> - Document how to represent DSI devices that are controller through
>>>   an external bus like I2C or SPI
>>>
>>> Changes in v2:
>>> - None
>>> ---
>>>  .../bindings/display/bridge/cdns,dsi.txt           | 109 +++++++++++++++++++++
>>>  1 file changed, 109 insertions(+)
>>>  create mode 100644 Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
>>> new file mode 100644
>>> index 000000000000..c70008bd8c0d
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
>>> @@ -0,0 +1,109 @@
>>> +Cadence DSI bridge
>>> +==================
>>> +
>>> +The Cadence DSI bridge is a DPI to DSI bridge supporting up to 4 DSI lanes.
>>> +
>>> +Required properties:
>>> +- compatible: should be set to "cdns,dsi-1.3.1".
>>> +- reg: physical base address and length of the controller's registers.
>>> +- interrupts: interrupt line connected to the DSI bridge.
>>> +- clocks: DSI bridge clocks.
>>> +- clock-names: must contain "pclk" and "sysclk".
>>> +- phys: phandle link to the MIPI D-PHY controller.
>>> +- phy-names: must contain "dphy".
>>> +- #address-cells: must be set to 1.
>>> +- #size-cells: must be set to 0.
>>> +
>>> +Required subnodes:
>>> +- ports: Ports as described in Documentation/devicetree/bindings/graph.txt.
>>> +  2 ports are available:
>>> +  * port 0: this port is only needed if some of your DSI devices are
>>> +	    controlled through  an external bus like I2C or SPI. Can have at
>>> +	    most 4 endpoints. The endpoint number is directly encoding the
>>> +	    DSI virtual channel used by this device.
>>> +  * port 1: represents the DPI input.
>>> +  Other ports will be added later to support the new kind of inputs.  
>> I think usual practice is to use lower numbers for input ports, higher
>> for output ports.
>> Is there a reason to do it this way?
> The main reason I did that is because we only have one output port and
> can have 1, 2 or 3 input ports: one is the DPI and the 2 others are
> called SDI (some kind of serial input). I thought it would be better to
> have all inputs using contiguous port numbers, and if we put inputs
> first that means having a hole between the input and output port (port 0
> would be the DPI input and port 3 the DSI output).
>
> Honestly, that's just a detail, so if you prefer to have the input
> ports start at 0 I'm fine with that.

No serious preferences, just curiosity. In fact port numbering schema is
private thing of the device node.

Regards
Andrzej

>
> Regards,
>
> Boris
>
>
>
>
>

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux