From: Patrick Bruenn <p.bruenn@xxxxxxxxxxxx> The CX9020 differs from i.MX53 Quick Start Board by: - use uart2 instead of uart1 - DVI-D connector instead of VGA - no audio - no SATA connector - CCAT FPGA connected to emi - enable rtc v5: - rebased on v4.13-rc2 - don't take maintainership for imx53-cx9020.dtsi, keep it to ARM/FREESCALE IMX maintainers - add explicit pinmux settings for pwr leds (EIM_D22 - D24) - remove display0->status="okay" - use "regulator-vbus" as name for usb_vbus regulator node - use correct reset values for explicit pinmux settings of: MX53_PAD_GPIO_0__CCM_CLKO MX53_PAD_GPIO_16__I2C3_SDA MX53_PAD_GPIO_1__ESDHC1_CD MX53_PAD_GPIO_3__GPIO1_3 MX53_PAD_GPIO_8__GPIO1_8 v4: - move alternative UART2 pinmux settings to imx53-pinfunc.h - fix copyright notice and model name to clearify cx9020 is a Beckhoff board and not from Freescale/NXP/Qualcomm - add "bhf,cx9020" compatible - remove ccat node and pin configuration as long as the ccat driver is not mainlined - use dvi-connector + ti,tfp410 instead of panel-simple - add newlines between property list and child nodes - replace underscores in node names with hypens - replace magic number 0 with polarity defines from include/dt-bindings/gpio/gpio.h - move rtc node into imx53.dtsi, change it's name into 'srtc', to avoid a conflict with 'rtc' node in imx53-m53.dtsi - rename regulator-3p2v - drop imx53-qsb container node - make iomux configuration explicit - remove unused audmux - remove unused led_pin_gpio3_23 configuration - use blue gpio-leds as disk-activity indicators for mmc0 and mmc1 - add mmc indicator leds to sdhc pingroups - keep node names in alphabetical order - remove unused sata and ssi2 - remove unused pin configs from hoggrp - add entry for Beckhoff related files to MAINTAINERS v3: add missig changelog v2: - keep alphabetic order of dts/Makefile - configure uart2 with 'fsl,dte-mode' - use display-0 and panel-0 as node names - remove unnecessary "simple-bus" for fixed regulators Patrick Bruenn (4): dt-bindings: arm: Add entry for Beckhoff CX9020 ARM: dts: imx53: add srtc node ARM: dts: imx53: add alternative UART2 configuration ARM: dts: imx: add CX9020 Embedded PC device tree Documentation/devicetree/bindings/arm/bhf.txt | 6 + .../devicetree/bindings/vendor-prefixes.txt | 1 + MAINTAINERS | 5 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx53-cx9020.dts | 297 +++++++++++++++++++++ arch/arm/boot/dts/imx53-pinfunc.h | 4 + arch/arm/boot/dts/imx53.dtsi | 9 + 7 files changed, 323 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/bhf.txt create mode 100644 arch/arm/boot/dts/imx53-cx9020.dts -- 2.11.0 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
