On Fri, Jul 21, 2017 at 06:06:40AM +0200, linux-kernel-dev@xxxxxxxxxxxx wrote: > From: Patrick Bruenn <p.bruenn@xxxxxxxxxxxx> > > The CX9020 differs from i.MX53 Quick Start Board by: > - use uart2 instead of uart1 > - DVI-D connector instead of VGA > - no audio > - no SATA connector > - CCAT FPGA connected to emi > - enable rtc > > Signed-off-by: Patrick Bruenn <p.bruenn@xxxxxxxxxxxx> Where is the patch 1/2? > > --- > > v4: > - move alternative UART2 pinmux settings to imx53-pinfunc.h > - fix copyright notice and model name to clearify cx9020 is a > Beckhoff board and not from Freescale/NXP/Qualcomm > - add "bhf,cx9020" compatible > - remove ccat node and pin configuration as long as the ccat > driver is not mainlined > - use dvi-connector + ti,tfp410 instead of panel-simple > - add newlines between property list and child nodes > - replace underscores in node names with hypens > - replace magic number 0 with polarity defines from > include/dt-bindings/gpio/gpio.h > - move rtc node into imx53.dtsi, change it's name into 'srtc', > to avoid a conflict with 'rtc' node in imx53-m53.dtsi > - rename regulator-3p2v > - drop imx53-qsb container node > - make iomux configuration explicit > - remove unused audmux > - remove unused led_pin_gpio3_23 configuration > - use blue gpio-leds as disk-activity indicators for mmc0 and mmc1 > - add mmc indicator leds to sdhc pingroups > - keep node names in alphabetical order > - remove unused sata and ssi2 > - remove unused pin configs from hoggrp > - add entry for imx53-cx9020.dts to MAINTAINERS > > v3: add missig changelog > v2: > - keep alphabetic order of dts/Makefile > - configure uart2 with 'fsl,dte-mode' > - use display-0 and panel-0 as node names > - remove unnecessary "simple-bus" for fixed regulators > > Cc: Andrew Lunn <andrew@xxxxxxx> > --- > MAINTAINERS | 1 + I do not take the changes on this file. > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx53-cx9020.dts | 295 +++++++++++++++++++++++++++++++++++++ > arch/arm/boot/dts/imx53-pinfunc.h | 4 + > arch/arm/boot/dts/imx53.dtsi | 9 ++ Please have separate patches for imx53-pinfunc.h and imx53.dtsi. Do not mix them up with board support dts changes. > 5 files changed, 310 insertions(+) > create mode 100644 arch/arm/boot/dts/imx53-cx9020.dts > > diff --git a/MAINTAINERS b/MAINTAINERS > index 1bf282843dc2..1bd06328f79b 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -1176,6 +1176,7 @@ ARM/BECKHOFF SUPPORT > M: Patrick Bruenn <p.bruenn@xxxxxxxxxxxx> > S: Maintained > F: Documentation/devicetree/bindings/arm/bhf.txt > +F: arch/arm/boot/dts/imx53-cx9020.dts > > ARM/CALXEDA HIGHBANK ARCHITECTURE > M: Rob Herring <robh@xxxxxxxxxx> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 4b17f35dc9a7..f0ba9be523e0 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -340,6 +340,7 @@ dtb-$(CONFIG_SOC_IMX51) += \ > imx51-ts4800.dtb > dtb-$(CONFIG_SOC_IMX53) += \ > imx53-ard.dtb \ > + imx53-cx9020.dtb \ > imx53-m53evk.dtb \ > imx53-mba53.dtb \ > imx53-qsb.dtb \ > diff --git a/arch/arm/boot/dts/imx53-cx9020.dts b/arch/arm/boot/dts/imx53-cx9020.dts > new file mode 100644 > index 000000000000..c4f9c89668c2 > --- /dev/null > +++ b/arch/arm/boot/dts/imx53-cx9020.dts > @@ -0,0 +1,295 @@ > +/* > + * Copyright 2017 Beckhoff Automation GmbH & Co. KG > + * based on imx53-qsb.dts > + * > + * The code contained herein is licensed under the GNU General Public > + * License. You may obtain a copy of the GNU General Public License > + * Version 2 or later at the following locations: > + * > + * http://www.opensource.org/licenses/gpl-license.html > + * http://www.gnu.org/copyleft/gpl.html > + */ > + > +/dts-v1/; > +#include "imx53.dtsi" > + > +/ { > + model = "Beckhoff CX9020 Embedded PC"; > + compatible = "bhf,cx9020", "fsl,imx53"; > + > + chosen { > + stdout-path = &uart2; > + }; > + > + memory { > + reg = <0x70000000 0x20000000>, > + <0xb0000000 0x20000000>; > + }; > + > + display-0 { > + #address-cells =<1>; > + #size-cells = <0>; > + compatible = "fsl,imx-parallel-display"; > + interface-pix-fmt = "rgb24"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ipu_disp0>; > + status = "okay"; This status line is not necessary. We usually use "okay" to toggle the status which is set "disabled" in <soc>.dtsi. > + > + port@0 { > + reg = <0>; > + > + display0_in: endpoint { > + remote-endpoint = <&ipu_di0_disp0>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + display0_out: endpoint { > + remote-endpoint = <&tfp410_in>; > + }; > + }; > + }; > + > + dvi-connector { > + compatible = "dvi-connector"; > + ddc-i2c-bus = <&i2c2>; > + digital; > + > + port { > + dvi_connector_in: endpoint { > + remote-endpoint = <&tfp410_out>; > + }; > + }; > + }; > + > + dvi-converter { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "ti,tfp410"; > + > + port@0 { > + reg = <0>; > + > + tfp410_in: endpoint { > + remote-endpoint = <&display0_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + tfp410_out: endpoint { > + remote-endpoint = <&dvi_connector_in>; > + }; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + pwr-r { > + gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + > + pwr-g { > + gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; > + default-state = "on"; > + }; > + > + pwr-b { > + gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + > + sd1-b { > + linux,default-trigger = "mmc0"; > + gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>; > + }; > + > + sd2-b { > + linux,default-trigger = "mmc1"; > + gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + regulator-3p2v { > + compatible = "regulator-fixed"; > + regulator-name = "3P2V"; > + regulator-min-microvolt = <3200000>; > + regulator-max-microvolt = <3200000>; > + regulator-always-on; > + }; > + > + reg_usb_vbus: regulator { The node name "regulator" is too generic. The "regulator-vbus" might be the one you want to use. Shawn > + compatible = "regulator-fixed"; > + regulator-name = "usb_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > +}; -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
