Enables the ADV7180 decoder sensor. The ADV7180 connects to the parallel-bus mux input on ipu1_csi0_mux. The ADV7180 power pin is via max7310_b port expander. Signed-off-by: Steve Longerbeam <steve_longerbeam@xxxxxxxxxx> - Use IRQ_TYPE_LEVEL_LOW instead of 0x8 for interrupt type for clarity. - For 8-bit parallel IPU1-CSI0 bus connection only data[12-19] are used. Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx> --- arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 45 ++++++++++++++++++++++++++++++++ 1 file changed, 45 insertions(+) diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi index 1212f82..6a7594e 100644 --- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi @@ -124,6 +124,21 @@ #size-cells = <0>; reg = <1>; + adv7180: camera@21 { + compatible = "adi,adv7180"; + reg = <0x21>; + powerdown-gpios = <&max7310_b 2 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio1>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + + port { + adv7180_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <8>; + }; + }; + }; + max7310_a: gpio@30 { compatible = "maxim,max7310"; reg = <0x30>; @@ -151,6 +166,20 @@ }; }; +&ipu1_csi0_from_ipu1_csi0_mux { + bus-width = <8>; +}; + +&ipu1_csi0_mux_from_parallel_sensor { + remote-endpoint = <&adv7180_to_ipu1_csi0_mux>; + bus-width = <8>; +}; + +&ipu1_csi0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ipu1_csi0>; +}; + &clks { assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>, <&clks IMX6QDL_PLL4_BYPASS>, @@ -444,6 +473,22 @@ >; }; + pinctrl_ipu1_csi0: ipu1csi0grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0 + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0 + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0 + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0 + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0 + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0 + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0 + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0 + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0 + MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x1b0b0 + MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x1b0b0 + >; + }; + pinctrl_max7310: max7310grp { fsl,pins = < MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x1b0b0 -- 2.7.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html