On 05/19/2017 07:42 AM, Keerthy wrote:
> The LP87565 chip is a power management IC for Portable Navigation Systems
> and Tablet Computing devices. It contains the following components:
>
> - Configurable Bucks(Single and multi-phase).
> - Configurable General Purpose Output Signals (GPO).
>
> The LP87565-Q1 variant device uses two 2-phase outputs configuration,
> Buck0 is master for Buck0/1 output and Buck2 is master for Buck2/3
> output.
>
> Signed-off-by: Keerthy <j-keerthy@xxxxxx>
> ---
> Documentation/devicetree/bindings/mfd/lp87565.txt | 44 ++++
> drivers/mfd/Kconfig | 14 ++
> drivers/mfd/Makefile | 1 +
> drivers/mfd/lp87565.c | 103 ++++++++
> include/linux/mfd/lp87565.h | 275 ++++++++++++++++++++++
> 5 files changed, 437 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/lp87565.txt
> create mode 100644 drivers/mfd/lp87565.c
> create mode 100644 include/linux/mfd/lp87565.h
>
> diff --git a/Documentation/devicetree/bindings/mfd/lp87565.txt b/Documentation/devicetree/bindings/mfd/lp87565.txt
> new file mode 100644
> index 0000000..38a00a1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/lp87565.txt
> @@ -0,0 +1,44 @@
> +TI LP873565 PMIC MFD driver
> +
> +Required properties:
> + - compatible: "ti,lp87565", "ti,lp87565-q1"
The of_device_id table in the driver only seems to match for
"ti,lp87565-q1", not "ti,lp87565".
> + - reg: I2C slave address.
> + - gpio-controller: Marks the device node as a GPIO Controller.
> + - #gpio-cells: Should be two. The first cell is the pin number and
> + the second cell is used to specify flags.
> + See ../gpio/gpio.txt for more information.
> + - xxx-in-supply: Phandle to parent supply node of each regulator
> + populated under regulators node. xxx should match
> + the supply_name populated in driver.
> + - regulators: List of child nodes that specify the regulator
> + initialization data.
> +Example:
> +
> +lp87565: lp87565@60 {
pmic: lp87565@60 {
Is more standard.
> + compatible = "ti,lp87565-q1";
> + reg = <0x60>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + buck10-in-supply =<&vsys_3v3>;
> + buck23-in-supply =<&vsys_3v3>;
> + regulators: regulators {
> + buck10_reg: buck10 {
> + /*VDD_MPU*/
> + regulator-name = "buck10";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + buck23_reg: buck23 {
> + /* VDD_GPU*/
> + regulator-name = "buck23";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> +};
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 3eb5c93..5e884f3 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -1325,6 +1325,20 @@ config MFD_TI_LP873X
> This driver can also be built as a module. If so, the module
> will be called lp873x.
>
> +config MFD_TI_LP87565
> + tristate "TI LP87565 Power Management IC"
> + depends on I2C
> + select MFD_CORE
> + select REGMAP_I2C
> + help
> + If you say yes here then you get support for the LP87565 series of
> + Power Management Integrated Circuits (PMIC).
> + These include voltage regulators, thermal protection, configurable
> + General Purpose Outputs (GPO) that are used in portable devices.
> +
> + This driver can also be built as a module. If so, the module
> + will be called lp87565.
> +
> config MFD_TPS65218
> tristate "TI TPS65218 Power Management chips"
> depends on I2C
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index c16bf1e..7edbe1b 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -25,6 +25,7 @@ obj-$(CONFIG_HTC_PASIC3) += htc-pasic3.o
> obj-$(CONFIG_HTC_I2CPLD) += htc-i2cpld.o
>
> obj-$(CONFIG_MFD_TI_LP873X) += lp873x.o
> +obj-$(CONFIG_MFD_TI_LP87565) += lp87565.o
>
> obj-$(CONFIG_MFD_DAVINCI_VOICECODEC) += davinci_voicecodec.o
> obj-$(CONFIG_MFD_DM355EVM_MSP) += dm355evm_msp.o
> diff --git a/drivers/mfd/lp87565.c b/drivers/mfd/lp87565.c
> new file mode 100644
> index 0000000..dff882f
> --- /dev/null
> +++ b/drivers/mfd/lp87565.c
> @@ -0,0 +1,103 @@
> +/*
> + * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * Author: Keerthy <j-keerthy@xxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation version 2.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether express or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/interrupt.h>
> +#include <linux/mfd/core.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/regmap.h>
> +
> +#include <linux/mfd/lp87565.h>
> +
> +static const struct regmap_config lp87565_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .max_register = LP87565_REG_MAX,
> +};
> +
> +static const struct mfd_cell lp87565_cells[] = {
> + { .name = "lp87565-q1-regulator", },
> + { .name = "lp87565-q1-gpio", },
> +};
> +
> +static const struct of_device_id of_lp87565_match_table[] = {
> + {
> + .compatible = "ti,lp87565-q1",
> + .data = (void *)LP87565_DEVICE_TYPE_LP87565_Q1,
> + },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, of_lp87565_match_table);
> +
> +static int lp87565_probe(struct i2c_client *client,
> + const struct i2c_device_id *ids)
> +{
> + struct lp87565 *lp87565;
> + const struct of_device_id *of_id;
> + int ret;
> + unsigned int otpid;
> +
> + lp87565 = devm_kzalloc(&client->dev, sizeof(*lp87565), GFP_KERNEL);
> + if (!lp87565)
> + return -ENOMEM;
> +
> + lp87565->dev = &client->dev;
> +
> + lp87565->regmap = devm_regmap_init_i2c(client, &lp87565_regmap_config);
> + if (IS_ERR(lp87565->regmap)) {
> + ret = PTR_ERR(lp87565->regmap);
> + dev_err(lp87565->dev,
> + "Failed to initialize register map: %d\n", ret);
> + return ret;
> + }
> +
> + ret = regmap_read(lp87565->regmap, LP87565_REG_OTP_REV, &otpid);
> + if (ret) {
> + dev_err(lp87565->dev, "Failed to read OTP ID\n");
> + return ret;
> + }
> +
> + lp87565->rev = otpid & LP87565_OTP_REV_OTP_ID;
> + of_id = of_match_device(of_lp87565_match_table, &client->dev);
> + if (of_id)
> + lp87565->dev_type = (enum lp87565_device_type)of_id->data;
> +
> + i2c_set_clientdata(client, lp87565);
> +
> + ret = mfd_add_devices(lp87565->dev, PLATFORM_DEVID_AUTO, lp87565_cells,
> + ARRAY_SIZE(lp87565_cells), NULL, 0, NULL);
> +
> + return ret;
> +}
> +
> +static const struct i2c_device_id lp87565_id_table[] = {
> + { "lp87565-q1", 0 },
> + { },
> +};
> +MODULE_DEVICE_TABLE(i2c, lp87565_id_table);
> +
> +static struct i2c_driver lp87565_driver = {
> + .driver = {
> + .name = "lp87565",
> + .of_match_table = of_lp87565_match_table,
> + },
> + .probe = lp87565_probe,
> + .id_table = lp87565_id_table,
> +};
> +module_i2c_driver(lp87565_driver);
> +
> +MODULE_AUTHOR("J Keerthy <j-keerthy@xxxxxx>");
> +MODULE_DESCRIPTION("lp87565 chip family Multi-Function Device driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/linux/mfd/lp87565.h b/include/linux/mfd/lp87565.h
> new file mode 100644
> index 0000000..6112365
> --- /dev/null
> +++ b/include/linux/mfd/lp87565.h
> @@ -0,0 +1,275 @@
> +/*
> + * Functions to access LP87565 power management chip.
> + *
> + * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation version 2.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether express or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef __LINUX_MFD_LP87565_H
> +#define __LINUX_MFD_LP87565_H
> +
> +#include <linux/i2c.h>
> +#include <linux/regulator/driver.h>
> +#include <linux/regulator/machine.h>
> +
> +enum lp87565_device_type {
> + LP87565_DEVICE_TYPE_UNKNOWN = 0,
> + LP87565_DEVICE_TYPE_LP87565_Q1,
> +};
> +
> +/* All register addresses */
> +#define LP87565_REG_DEV_REV 0X00
> +#define LP87565_REG_OTP_REV 0X01
> +#define LP87565_REG_BUCK0_CTRL_1 0X02
> +#define LP87565_REG_BUCK0_CTRL_2 0X03
> +
> +#define LP87565_REG_BUCK1_CTRL_1 0X04
> +#define LP87565_REG_BUCK1_CTRL_2 0X05
> +
> +#define LP87565_REG_BUCK2_CTRL_1 0X06
> +#define LP87565_REG_BUCK2_CTRL_2 0X07
> +
> +#define LP87565_REG_BUCK3_CTRL_1 0X08
> +#define LP87565_REG_BUCK3_CTRL_2 0X09
> +
> +#define LP87565_REG_BUCK0_VOUT 0X0A
> +#define LP87565_REG_BUCK0_FLOOR_VOUT 0X0B
> +
> +#define LP87565_REG_BUCK1_VOUT 0X0C
> +#define LP87565_REG_BUCK1_FLOOR_VOUT 0X0D
> +
> +#define LP87565_REG_BUCK2_VOUT 0X0E
> +#define LP87565_REG_BUCK2_FLOOR_VOUT 0X0F
> +
> +#define LP87565_REG_BUCK3_VOUT 0X10
> +#define LP87565_REG_BUCK3_FLOOR_VOUT 0X11
> +
> +#define LP87565_REG_BUCK0_DELAY 0X12
> +#define LP87565_REG_BUCK1_DELAY 0X13
> +
> +#define LP87565_REG_BUCK2_DELAY 0X14
> +#define LP87565_REG_BUCK3_DELAY 0X15
> +
> +#define LP87565_REG_GPO2_DELAY 0X16
> +#define LP87565_REG_GPO3_DELAY 0X17
> +#define LP87565_REG_RESET 0X18
> +#define LP87565_REG_CONFIG 0X19
> +
> +#define LP87565_REG_INT_TOP_1 0X1A
> +#define LP87565_REG_INT_TOP_2 0X1B
> +
> +#define LP87565_REG_INT_BUCK_0_1 0X1C
> +#define LP87565_REG_INT_BUCK_2_3 0X1D
> +#define LP87565_REG_TOP_STAT 0X1E
> +#define LP87565_REG_BUCK_0_1_STAT 0X1F
> +#define LP87565_REG_BUCK_2_3_STAT 0x20
> +
> +#define LP87565_REG_TOP_MASK_1 0x21
> +#define LP87565_REG_TOP_MASK_2 0x22
> +
> +#define LP87565_REG_BUCK_0_1_MASK 0x23
> +#define LP87565_REG_BUCK_2_3_MASK 0x24
> +#define LP87565_REG_SEL_I_LOAD 0x25
> +
> +#define LP87565_REG_I_LOAD_2 0x26
> +#define LP87565_REG_I_LOAD_1 0x27
> +
> +#define LP87565_REG_PGOOD_CTRL1 0x28
> +#define LP87565_REG_PGOOD_CTRL2 0x29
> +#define LP87565_REG_PGOOD_FLT 0x2A
> +#define LP87565_REG_PLL_CTRL 0x2B
> +#define LP87565_REG_PIN_FUNCTION 0x2C
> +#define LP87565_REG_GPIO_CONFIG 0x2D
> +#define LP87565_REG_GPIO_IN 0x2E
> +#define LP87565_REG_GPIO_OUT 0x2F
> +
> +#define LP87565_REG_MAX LP87565_REG_GPIO_OUT
> +
> +/* Register field definitions */
> +#define LP87565_DEV_REV_DEV_ID 0xC0
> +#define LP87565_DEV_REV_ALL_LAYER 0x30
> +#define LP87565_DEV_REV_METAL_LAYER 0x0F
> +
> +#define LP87565_OTP_REV_OTP_ID 0xFF
> +
> +#define LP87565_BUCK_CTRL_1_EN BIT(7)
> +#define LP87565_BUCK_CTRL_1_EN_PIN_CTRL BIT(6)
> +#define LP87565_BUCK_CTRL_1_PIN_SELECT_EN 0x30
> +
> +#define LP87565_BUCK_CTRL_1_ROOF_FLOOR_EN BIT(3)
> +#define LP87565_BUCK_CTRL_1_RDIS_EN BIT(2)
> +#define LP87565_BUCK_CTRL_1_FPWM BIT(1)
> +/* Bit0 is reserved for BUCK1 and BUCK3 and valid only for BUCK0 and BUCK2 */
> +#define LP87565_BUCK_CTRL_1_FPWM_MP_0_2 BIT(0)
> +
> +#define LP87565_BUCK_CTRL_2_ILIM 0x38
> +#define LP87565_BUCK_CTRL_2_SLEW_RATE 0x07
> +
> +#define LP87565_BUCK_VSET 0xFF
> +#define LP87565_BUCK_FLOOR_VSET 0xFF
> +
> +#define LP87565_BUCK_SHUTDOWN_DELAY 0xF0
> +#define LP87565_BUCK_STARTUP_DELAY 0x0F
> +
> +#define LP87565_GPIO_SHUTDOWN_DELAY 0xF0
> +#define LP87565_GPIO_STARTUP_DELAY 0x0F
> +
> +#define LP87565_RESET_SW_RESET BIT(0)
> +
> +#define LP87565_CONFIG_DOUBLE_DELAY BIT(7)
> +#define LP87565_CONFIG_CLKIN_PD BIT(6)
> +#define LP87565_CONFIG_EN4_PD BIT(5)
> +#define LP87565_CONFIG_EN3_PD BIT(4)
> +#define LP87565_CONFIG_TDIE_WARN_LEVEL BIT(3)
> +#define LP87565_CONFIG_EN2_PD BIT(2)
> +#define LP87565_CONFIG_EN1_PD BIT(1)
> +
> +#define LP87565_INT_GPIO BIT(7)
> +#define LP87565_INT_BUCK23 BIT(6)
> +#define LP87565_INT_BUCK01 BIT(5)
> +#define LP87565_NO_SYNC_CLK BIT(4)
> +#define LP87565_TDIE_SD BIT(3)
> +#define LP87565_TDIE_WARN BIT(2)
> +#define LP87565_INT_OVP BIT(1)
> +#define LP87565_I_LOAD_READY BIT(0)
> +
> +#define LP87565_INT_TOP2_RESET_REG BIT(0)
> +
> +#define LP87565_BUCK1_PG_INT BIT(6)
> +#define LP87565_BUCK1_SC_INT BIT(5)
> +#define LP87565_BUCK1_ILIM_INT BIT(4)
> +#define LP87565_BUCK0_PG_INT BIT(2)
> +#define LP87565_BUCK0_SC_INT BIT(1)
> +#define LP87565_BUCK0_ILIM_INT BIT(0)
> +
> +#define LP87565_BUCK3_PG_INT BIT(6)
> +#define LP87565_BUCK3_SC_INT BIT(5)
> +#define LP87565_BUCK3_ILIM_INT BIT(4)
> +#define LP87565_BUCK2_PG_INT BIT(2)
> +#define LP87565_BUCK2_SC_INT BIT(1)
> +#define LP87565_BUCK2_ILIM_INT BIT(0)
> +
> +#define LP87565_SYNC_CLK_STAT BIT(4)
> +#define LP87565_TDIE_SD_STAT BIT(3)
> +#define LP87565_TDIE_WARN_STAT BIT(2)
> +#define LP87565_OVP_STAT BIT(1)
> +
> +#define LP87565_BUCK1_STAT BIT(7)
> +#define LP87565_BUCK1_PG_STAT BIT(6)
> +#define LP87565_BUCK1_ILIM_STAT BIT(4)
> +#define LP87565_BUCK0_STAT BIT(3)
> +#define LP87565_BUCK0_PG_STAT BIT(2)
> +#define LP87565_BUCK0_ILIM_STAT BIT(0)
> +
> +#define LP87565_BUCK3_STAT BIT(7)
> +#define LP87565_BUCK3_PG_STAT BIT(6)
> +#define LP87565_BUCK3_ILIM_STAT BIT(4)
> +#define LP87565_BUCK2_STAT BIT(3)
> +#define LP87565_BUCK2_PG_STAT BIT(2)
> +#define LP87565_BUCK2_ILIM_STAT BIT(0)
> +
> +#define LPL87565_GPIO_MASK BIT(7)
> +#define LPL87565_SYNC_CLK_MASK BIT(4)
> +#define LPL87565_TDIE_WARN_MASK BIT(2)
> +#define LPL87565_I_LOAD_READY_MASK BIT(0)
> +
> +#define LPL87565_RESET_REG_MASK BIT(0)
> +
> +#define LPL87565_BUCK1_PG_MASK BIT(6)
> +#define LPL87565_BUCK1_ILIM_MASK BIT(4)
> +#define LPL87565_BUCK0_PG_MASK BIT(2)
> +#define LPL87565_BUCK0_ILIM_MASK BIT(0)
> +
> +#define LPL87565_BUCK3_PG_MASK BIT(6)
> +#define LPL87565_BUCK3_ILIM_MASK BIT(4)
> +#define LPL87565_BUCK2_PG_MASK BIT(2)
> +#define LPL87565_BUCK2_ILIM_MASK BIT(0)
> +
> +#define LP87565_LOAD_CURRENT_BUCK_SELECT 0x3
> +
> +#define LP87565_I_LOAD2_BUCK_LOAD_CURRENT 0x3
> +#define LP87565_I_LOAD1_BUCK_LOAD_CURRENT 0xFF
> +
> +#define LP87565_PG3_SEL 0xC0
> +#define LP87565_PG2_SEL 0x30
> +#define LP87565_PG1_SEL 0x0C
> +#define LP87565_PG0_SEL 0x03
> +
> +#define LP87565_HALF_DAY BIT(7)
> +#define LP87565_EN_PG0_NINT BIT(6)
> +#define LP87565_PGOOD_SET_DELAY BIT(5)
> +#define LP87565_EN_PGFLT_STAT BIT(4)
> +#define LP87565_PGOOD_WINDOW BIT(2)
> +#define LP87565_PGOOD_OD BIT(1)
> +#define LP87565_PGOOD_POL BIT(0)
> +
> +#define LP87565_PG3_FLT BIT(3)
> +#define LP87565_PG2_FLT BIT(2)
> +#define LP87565_PG1_FLT BIT(1)
> +#define LP87565_PG0_FLT BIT(0)
> +
> +#define LP87565_PLL_MODE 0xC0
> +#define LP87565_EXT_CLK_FREQ 0x1F
> +
> +#define LP87565_EN_SPREAD_SPEC BIT(7)
> +#define LP87565_EN_PIN_CTRL_GPIO3 BIT(6)
> +#define LP87565_EN_PIN_SELECT_GPIO3 BIT(5)
> +#define LP87565_EN_PIN_CTRL_GPIO2 BIT(4)
> +#define LP87565_EN_PIN_SELECT_GPIO2 BIT(3)
> +#define LP87565_GPIO3_SEL BIT(2)
> +#define LP87565_GPIO2_SEL BIT(1)
> +#define LP87565_GPIO1_SEL BIT(0)
> +
> +#define LP87565_GOIO3_OD BIT(6)
> +#define LP87565_GOIO2_OD BIT(5)
> +#define LP87565_GOIO1_OD BIT(4)
> +#define LP87565_GOIO3_DIR BIT(2)
> +#define LP87565_GOIO2_DIR BIT(1)
> +#define LP87565_GOIO1_DIR BIT(0)
> +
> +#define LP87565_GOIO3_IN BIT(2)
> +#define LP87565_GOIO2_IN BIT(1)
> +#define LP87565_GOIO1_IN BIT(0)
> +
> +#define LP87565_GOIO3_OUT BIT(2)
> +#define LP87565_GOIO2_OUT BIT(1)
> +#define LP87565_GOIO1_OUT BIT(0)
> +
> +/* Number of step-down converters available */
> +#define LP87565_NUM_BUCK 6
> +
> +enum LP87565_regulator_id {
> + /* BUCK's */
> + LP87565_BUCK_0,
> + LP87565_BUCK_1,
> + LP87565_BUCK_2,
> + LP87565_BUCK_3,
> + LP87565_BUCK_10,
> + LP87565_BUCK_23,
> +};
> +
> +/**
> + * struct LP87565 - state holder for the LP87565 driver
> + * @dev: struct device pointer for MFD device
> + * @rev: revision of the LP87565
> + * @dev_type: The device type for example lp87565-q1
> + * @lock: lock guarding the data structure
> + * @regmap: register map of the LP87565 PMIC
> + *
> + * Device data may be used to access the LP87565 chip
> + */
> +struct lp87565 {
> + struct device *dev;
> + u8 rev;
> + u8 dev_type;
> + struct regmap *regmap;
> +};
> +#endif /* __LINUX_MFD_LP87565_H */
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
