From: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx> This driver starts the DWC2 core(s) built into the XWAY SoCs and provides the PHY interfaces for each core. The phy instances can be passed to the dwc2 driver, which already supports the generic phy interface. Signed-off-by: Hauke Mehrtens <hauke@xxxxxxxxxx> --- .../bindings/phy/phy-lantiq-rcu-usb2.txt | 59 ++++ arch/mips/lantiq/xway/reset.c | 43 --- arch/mips/lantiq/xway/sysctrl.c | 24 +- drivers/phy/Kconfig | 8 + drivers/phy/Makefile | 1 + drivers/phy/phy-lantiq-rcu-usb2.c | 325 +++++++++++++++++++++ 6 files changed, 405 insertions(+), 55 deletions(-) create mode 100644 Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt create mode 100644 drivers/phy/phy-lantiq-rcu-usb2.c diff --git a/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt new file mode 100644 index 000000000000..0ec9f790b6e0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt @@ -0,0 +1,59 @@ +Lantiq XWAY SoC RCU USB 1.1/2.0 PHY binding +=========================================== + +This binding describes the USB PHY hardware provided by the RCU module on the +Lantiq XWAY SoCs. + + +------------------------------------------------------------------------------- +Required properties (controller (parent) node): +- compatible : Should be one of + "lantiq,ase-rcu-usb2-phy" + "lantiq,danube-rcu-usb2-phy" + "lantiq,xrx100-rcu-usb2-phy" + "lantiq,xrx200-rcu-usb2-phy" + "lantiq,xrx300-rcu-usb2-phy" +- lantiq,rcu-syscon : A phandle to the RCU module and the offsets to the + USB PHY configuration and USB MAC registers. +- address-cells : should be 1 +- size-cells : should be 0 +- phy-cells : from the generic PHY bindings, must be 1 + +Optional properties (controller (parent) node): +- vbus-gpio : References a GPIO which enables VBUS all given USB + ports. + +Required nodes : A sub-node is required for each USB PHY port. + + +------------------------------------------------------------------------------- +Required properties (port (child) node): +- reg : The ID of the USB port, usually 0 or 1. +- clocks : References to the (PMU) "ctrl" and "phy" clk gates. +- clock-names : Must be one of the following: + "ctrl" + "phy" +- resets : References to the RCU USB configuration reset bits. +- reset-names : Must be one of the following: + "analog-config" (optional) + "statemachine-soft" (optional) + +Optional properties (port (child) node): +- vbus-gpio : References a GPIO which enables VBUS for the USB port. + + +------------------------------------------------------------------------------- +Example for the USB PHYs on an xRX200 SoC: + usb_phys0: rcu-usb2-phy@0 { + compatible = "lantiq,xrx200-rcu-usb2-phy"; + reg = <0>; + + lantiq,rcu-syscon = <&rcu0 0x18 0x38>; + clocks = <&pmu PMU_GATE_USB0_CTRL>, + <&pmu PMU_GATE_USB0_PHY>; + clock-names = "ctrl", "phy"; + vbus-gpios = <&gpio 32 GPIO_ACTIVE_HIGH>; + resets = <&rcu_reset1 4>, <&rcu_reset0 4>; + reset-names = "phy", "ctrl"; + #phy-cells = <0>; + }; diff --git a/arch/mips/lantiq/xway/reset.c b/arch/mips/lantiq/xway/reset.c index 3f30fb81a50f..5aec1f54275b 100644 --- a/arch/mips/lantiq/xway/reset.c +++ b/arch/mips/lantiq/xway/reset.c @@ -124,45 +124,6 @@ static void ltq_machine_power_off(void) unreachable(); } -static void ltq_usb_init(void) -{ - /* Power for USB cores 1 & 2 */ - ltq_pmu_enable(PMU_AHBM); - ltq_pmu_enable(PMU_USB0); - ltq_pmu_enable(PMU_USB1); - - ltq_rcu_w32(ltq_rcu_r32(RCU_CFG1A) | BIT(0), RCU_CFG1A); - ltq_rcu_w32(ltq_rcu_r32(RCU_CFG1B) | BIT(0), RCU_CFG1B); - - /* Enable USB PHY power for cores 1 & 2 */ - ltq_pmu_enable(PMU_USB0_P); - ltq_pmu_enable(PMU_USB1_P); - - /* Configure cores to host mode */ - ltq_rcu_w32(ltq_rcu_r32(RCU_USB1CFG) & ~RCU_USBCFG_HDSEL_BIT, - RCU_USB1CFG); - ltq_rcu_w32(ltq_rcu_r32(RCU_USB2CFG) & ~RCU_USBCFG_HDSEL_BIT, - RCU_USB2CFG); - - /* Select DMA endianness (Host-endian: big-endian) */ - ltq_rcu_w32((ltq_rcu_r32(RCU_USB1CFG) & ~RCU_USBCFG_SLV_END_BIT) - | RCU_USBCFG_HOST_END_BIT, RCU_USB1CFG); - ltq_rcu_w32(ltq_rcu_r32((RCU_USB2CFG) & ~RCU_USBCFG_SLV_END_BIT) - | RCU_USBCFG_HOST_END_BIT, RCU_USB2CFG); - - /* Hard reset USB state machines */ - ltq_rcu_w32(ltq_rcu_r32(RCU_USBRESET) | USBRESET_BIT, RCU_USBRESET); - udelay(50 * 1000); - ltq_rcu_w32(ltq_rcu_r32(RCU_USBRESET) & ~USBRESET_BIT, RCU_USBRESET); - - /* Soft reset USB state machines */ - ltq_rcu_w32(ltq_rcu_r32(RCU_USBRESET2) - | USB1RESET_BIT | USB2RESET_BIT, RCU_USBRESET2); - udelay(50 * 1000); - ltq_rcu_w32(ltq_rcu_r32(RCU_USBRESET2) - & ~(USB1RESET_BIT | USB2RESET_BIT), RCU_USBRESET2); -} - static int __init mips_reboot_setup(void) { struct resource res; @@ -186,10 +147,6 @@ static int __init mips_reboot_setup(void) if (!ltq_rcu_membase) panic("Failed to remap core memory"); - if (of_machine_is_compatible("lantiq,ar9") || - of_machine_is_compatible("lantiq,vr9")) - ltq_usb_init(); - _machine_restart = ltq_machine_restart; _machine_halt = ltq_machine_halt; pm_power_off = ltq_machine_power_off; diff --git a/arch/mips/lantiq/xway/sysctrl.c b/arch/mips/lantiq/xway/sysctrl.c index 5764d3ddce69..18725f2d5b67 100644 --- a/arch/mips/lantiq/xway/sysctrl.c +++ b/arch/mips/lantiq/xway/sysctrl.c @@ -469,8 +469,8 @@ void __init ltq_soc_init(void) if (of_machine_is_compatible("lantiq,grx390") || of_machine_is_compatible("lantiq,ar10")) { - clkdev_add_pmu("1e101000.usb", "phy", 1, 2, PMU_ANALOG_USB0_P); - clkdev_add_pmu("1e106000.usb", "phy", 1, 2, PMU_ANALOG_USB1_P); + clkdev_add_pmu("1f203000.rcu:rcu-usb2-phy@0", "phy", 1, 2, PMU_ANALOG_USB0_P); + clkdev_add_pmu("1f203000.rcu:rcu-usb2-phy@1", "phy", 1, 2, PMU_ANALOG_USB1_P); /* rc 0 */ clkdev_add_pmu("1d900000.pcie", "phy", 1, 2, PMU_ANALOG_PCIE0_P); clkdev_add_pmu("1d900000.pcie", "msi", 1, 1, PMU1_PCIE_MSI); @@ -490,8 +490,8 @@ void __init ltq_soc_init(void) else clkdev_add_static(CLOCK_133M, CLOCK_133M, CLOCK_133M, CLOCK_133M); - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0); - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); + clkdev_add_pmu("1f203000.rcu:rcu-usb2-phy@0", "ctrl", 1, 0, PMU_USB0); + clkdev_add_pmu("1f203000.rcu:rcu-usb2-phy@0", "phy", 1, 0, PMU_USB0_P); clkdev_add_pmu("1e180000.etop", "ppe", 1, 0, PMU_PPE); clkdev_add_cgu("1e180000.etop", "ephycgu", CGU_EPHY); clkdev_add_pmu("1e180000.etop", "ephy", 1, 0, PMU_EPHY); @@ -525,10 +525,10 @@ void __init ltq_soc_init(void) } else if (of_machine_is_compatible("lantiq,vr9")) { clkdev_add_static(ltq_vr9_cpu_hz(), ltq_vr9_fpi_hz(), ltq_vr9_fpi_hz(), ltq_vr9_pp32_hz()); - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0 | PMU_AHBM); - clkdev_add_pmu("1e106000.usb", "phy", 1, 0, PMU_USB1_P); - clkdev_add_pmu("1e106000.usb", "ctl", 1, 0, PMU_USB1 | PMU_AHBM); + clkdev_add_pmu("1f203000.rcu:rcu-usb2-phy@0", "phy", 1, 0, PMU_USB0_P); + clkdev_add_pmu("1f203000.rcu:rcu-usb2-phy@0", "ctrl", 1, 0, PMU_USB0 | PMU_AHBM); + clkdev_add_pmu("1f203000.rcu:rcu-usb2-phy@1", "phy", 1, 0, PMU_USB1_P); + clkdev_add_pmu("1f203000.rcu:rcu-usb2-phy@1", "ctrl", 1, 0, PMU_USB1 | PMU_AHBM); clkdev_add_pmu("1d900000.pcie", "phy", 1, 1, PMU1_PCIE_PHY); clkdev_add_pmu("1d900000.pcie", "bus", 1, 0, PMU_PCIE_CLK); clkdev_add_pmu("1d900000.pcie", "msi", 1, 1, PMU1_PCIE_MSI); @@ -548,8 +548,8 @@ void __init ltq_soc_init(void) } else if (of_machine_is_compatible("lantiq,ar9")) { clkdev_add_static(ltq_ar9_cpu_hz(), ltq_ar9_fpi_hz(), ltq_ar9_fpi_hz(), CLOCK_250M); - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0); - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); + clkdev_add_pmu("1f203000.rcu:rcu-usb2-phy@0", "ctrl", 1, 0, PMU_USB0); + clkdev_add_pmu("1f203000.rcu:rcu-usb2-phy@0", "phy", 1, 0, PMU_USB0_P); clkdev_add_pmu("1e106000.usb", "ctl", 1, 0, PMU_USB1); clkdev_add_pmu("1e106000.usb", "phy", 1, 0, PMU_USB1_P); clkdev_add_pmu("1e180000.etop", "switch", 1, 0, PMU_SWITCH); @@ -560,8 +560,8 @@ void __init ltq_soc_init(void) } else { clkdev_add_static(ltq_danube_cpu_hz(), ltq_danube_fpi_hz(), ltq_danube_fpi_hz(), ltq_danube_pp32_hz()); - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0); - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); + clkdev_add_pmu("1f203000.rcu:rcu-usb2-phy@0", "ctrl", 1, 0, PMU_USB0); + clkdev_add_pmu("1f203000.rcu:rcu-usb2-phy@0", "phy", 1, 0, PMU_USB0_P); clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO); clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU); clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE); diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index 005cadb7a3f8..dbb450e3ba04 100644 --- a/drivers/phy/Kconfig +++ b/drivers/phy/Kconfig @@ -488,6 +488,14 @@ config PHY_CYGNUS_PCIE Enable this to support the Broadcom Cygnus PCIe PHY. If unsure, say N. +config PHY_LANTIQ_RCU_USB2 + tristate "Lantiq XWAY SoC RCU based USB PHY" + depends on SOC_TYPE_XWAY + depends on OF + select GENERIC_PHY + help + Support for the USB PHY(s) on the Lantiq XWAY family SoCs. + source "drivers/phy/tegra/Kconfig" config PHY_NS2_PCIE diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index dd8f3b5d2918..52631f5ac470 100644 --- a/drivers/phy/Makefile +++ b/drivers/phy/Makefile @@ -59,6 +59,7 @@ obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o obj-$(CONFIG_PHY_CYGNUS_PCIE) += phy-bcm-cygnus-pcie.o +obj-$(CONFIG_PHY_LANTIQ_RCU_USB2) += phy-lantiq-rcu-usb2.o obj-$(CONFIG_ARCH_TEGRA) += tegra/ obj-$(CONFIG_PHY_NS2_PCIE) += phy-bcm-ns2-pcie.o obj-$(CONFIG_PHY_MESON8B_USB2) += phy-meson8b-usb2.o diff --git a/drivers/phy/phy-lantiq-rcu-usb2.c b/drivers/phy/phy-lantiq-rcu-usb2.c new file mode 100644 index 000000000000..9bff42afd256 --- /dev/null +++ b/drivers/phy/phy-lantiq-rcu-usb2.c @@ -0,0 +1,325 @@ +/* + * Lantiq XWAY SoC RCU module based USB 1.1/2.0 PHY driver + * + * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx> + * Copyright (C) 2017 Hauke Mehrtens <hauke@xxxxxxxxxx> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/gpio/consumer.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_gpio.h> +#include <linux/phy/phy.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/reset.h> + +#define MAX_VBUS_GPIO 2 + +/* Transmitter HS Pre-Emphasis Enable */ +#define RCU_CFG1_TX_PEE BIT(0) +/* Disconnect Threshold */ +#define RCU_CFG1_DIS_THR_MASK 0x00038000 +#define RCU_CFG1_DIS_THR_SHIFT 15 + +struct ltq_rcu_usb2_bits { + u8 hostmode; + u8 slave_endianness; + u8 host_endianness; + bool have_ana_cfg; +}; + +struct ltq_rcu_usb2_priv { + struct regmap *regmap; + u32 phy_reg_offset; + u32 ana_cfg1_reg_offset; + const struct ltq_rcu_usb2_bits *reg_bits; + struct device *dev; + struct gpio_desc *gpiod_vbus[MAX_VBUS_GPIO]; + struct phy *phy; + struct clk *ctrl_gate_clk; + struct clk *phy_gate_clk; + struct reset_control *ctrl_reset; + struct reset_control *phy_reset; +}; + +static const struct ltq_rcu_usb2_bits xway_rcu_usb2_reg_bits = { + .hostmode = 11, + .slave_endianness = 9, + .host_endianness = 10, + .have_ana_cfg = false, +}; + +static const struct ltq_rcu_usb2_bits xrx100_rcu_usb2_reg_bits = { + .hostmode = 11, + .slave_endianness = 17, + .host_endianness = 10, + .have_ana_cfg = false, +}; + +static const struct ltq_rcu_usb2_bits xrx200_rcu_usb2_reg_bits = { + .hostmode = 11, + .slave_endianness = 9, + .host_endianness = 10, + .have_ana_cfg = true, +}; + +static const struct of_device_id ltq_rcu_usb2_phy_of_match[] = { + { + .compatible = "lantiq,ase-rcu-usb2-phy", + .data = &xway_rcu_usb2_reg_bits, + }, + { + .compatible = "lantiq,danube-rcu-usb2-phy", + .data = &xway_rcu_usb2_reg_bits, + }, + { + .compatible = "lantiq,xrx100-rcu-usb2-phy", + .data = &xrx100_rcu_usb2_reg_bits, + }, + { + .compatible = "lantiq,xrx200-rcu-usb2-phy", + .data = &xrx200_rcu_usb2_reg_bits, + }, + { + .compatible = "lantiq,xrx300-rcu-usb2-phy", + .data = &xrx200_rcu_usb2_reg_bits, + }, + { }, +}; +MODULE_DEVICE_TABLE(of, ltq_rcu_usb2_phy_of_match); + +static void ltq_rcu_usb2_set_vbus_gpio_value(struct gpio_desc **gpiods, + int value) +{ + int i; + + for (i = 0; i < MAX_VBUS_GPIO; i++) + if (!IS_ERR_OR_NULL(gpiods[i])) + gpiod_set_value(gpiods[i], value); +} + +static int ltq_rcu_usb2_phy_power_on(struct phy *phy) +{ + struct ltq_rcu_usb2_priv *priv = phy_get_drvdata(phy); + + if (priv->phy_reset) + reset_control_deassert(priv->phy_reset); + + /* enable the port-specific VBUS GPIOs if available */ + ltq_rcu_usb2_set_vbus_gpio_value(priv->gpiod_vbus, 1); + + return 0; +} + +static int ltq_rcu_usb2_phy_power_off(struct phy *phy) +{ + struct ltq_rcu_usb2_priv *priv = phy_get_drvdata(phy); + + /* + * only disable the port-specific VBUS GPIO here (if available), the + * shared VBUS GPIO might still be used by another port + */ + ltq_rcu_usb2_set_vbus_gpio_value(priv->gpiod_vbus, 0); + + if (priv->phy_reset) + reset_control_assert(priv->phy_reset); + + return 0; +} + +static struct phy_ops ltq_rcu_usb2_phy_ops = { + .power_on = ltq_rcu_usb2_phy_power_on, + .power_off = ltq_rcu_usb2_phy_power_off, + .owner = THIS_MODULE, +}; + +static void ltq_rcu_usb2_start_cores(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct ltq_rcu_usb2_priv *priv = dev_get_drvdata(dev); + + /* Power on the USB core. */ + if (clk_prepare_enable(priv->ctrl_gate_clk)) { + dev_err(dev, "failed to enable CTRL gate\n"); + return; + } + + /* + * Power on the USB PHY. We have to do it early because + * otherwise the second core won't turn on properly. + */ + if (clk_prepare_enable(priv->phy_gate_clk)) { + dev_err(dev, "failed to enable PHY gate\n"); + return; + } + + if (priv->reg_bits->have_ana_cfg) { + regmap_update_bits(priv->regmap, priv->ana_cfg1_reg_offset, + RCU_CFG1_TX_PEE, RCU_CFG1_TX_PEE); + regmap_update_bits(priv->regmap, priv->ana_cfg1_reg_offset, + RCU_CFG1_DIS_THR_MASK, 7 << RCU_CFG1_DIS_THR_SHIFT); + } + + /* Configure core to host mode */ + regmap_update_bits(priv->regmap, priv->phy_reg_offset, + BIT(priv->reg_bits->hostmode), 0); + + /* Select DMA endianness (Host-endian: big-endian) */ + regmap_update_bits(priv->regmap, priv->phy_reg_offset, + BIT(priv->reg_bits->slave_endianness), 0); + regmap_update_bits(priv->regmap, priv->phy_reg_offset, + BIT(priv->reg_bits->host_endianness), + BIT(priv->reg_bits->host_endianness)); + + /* Reset USB core throgh reset controller */ + reset_control_deassert(priv->ctrl_reset); + + if (priv->phy_reset) + reset_control_assert(priv->phy_reset); +} + +static int ltq_rcu_usb2_get_vbus_gpios(struct device *dev, + struct gpio_desc **gpios) +{ + int i; + + for (i = 0; i < MAX_VBUS_GPIO; i++) { + gpios[i] = devm_gpiod_get_index_optional(dev, "vbus", i, + GPIOD_OUT_LOW); + if (IS_ERR(gpios[i])) + return PTR_ERR(gpios[i]); + } + + return 0; +} + +static int ltq_rcu_usb2_of_probe(struct device_node *phynode, + struct ltq_rcu_usb2_priv *priv) +{ + struct device *dev = priv->dev; + const struct of_device_id *match = + of_match_node(ltq_rcu_usb2_phy_of_match, phynode); + int ret; + + if (!match) { + dev_err(dev, "Not a compatible Lantiq RCU USB PHY\n"); + return -EINVAL; + } + + priv->reg_bits = match->data; + + priv->regmap = syscon_regmap_lookup_by_phandle(phynode, + "lantiq,rcu-syscon"); + if (IS_ERR(priv->regmap)) { + dev_err(dev, "Failed to lookup RCU regmap\n"); + return PTR_ERR(priv->regmap); + } + + ret = ltq_rcu_usb2_get_vbus_gpios(dev, priv->gpiod_vbus); + if (ret) { + dev_err(dev, "failed to request shared USB VBUS GPIO\n"); + return ret; + } + + priv->ctrl_gate_clk = devm_clk_get(dev, "ctrl"); + if (IS_ERR(priv->ctrl_gate_clk)) { + dev_err(dev, "Unable to get USB ctrl gate clk\n"); + return PTR_ERR(priv->ctrl_gate_clk); + } + + priv->phy_gate_clk = devm_clk_get(dev, "phy"); + if (IS_ERR(priv->phy_gate_clk)) { + dev_err(dev, "Unable to get USB phy gate clk\n"); + return PTR_ERR(priv->phy_gate_clk); + } + + priv->ctrl_reset = devm_reset_control_get_shared(dev, "ctrl"); + if (IS_ERR(priv->ctrl_reset)) { + dev_err(dev, "failed to get 'ctrl' reset\n"); + return PTR_ERR(priv->ctrl_reset); + } + + priv->phy_reset = devm_reset_control_get_optional(dev, "phy"); + if (IS_ERR(priv->phy_reset)) { + if (PTR_ERR(priv->phy_reset) == -EPROBE_DEFER) + return PTR_ERR(priv->phy_reset); + priv->phy_reset = NULL; + } + + ret = of_property_read_u32_index(phynode, "lantiq,rcu-syscon", 1, + &priv->phy_reg_offset); + if (ret) { + dev_err(dev, "Failed to get RCU PHY reg offset\n"); + return ret; + } + + if (priv->reg_bits->have_ana_cfg) { + ret = of_property_read_u32_index(phynode, "lantiq,rcu-syscon", + 2, &priv->ana_cfg1_reg_offset); + if (ret) { + dev_dbg(dev, "Failed to get RCU ANA CFG1 reg offset\n"); + return ret; + } + } + + return 0; +} + +static int ltq_rcu_usb2_phy_probe(struct platform_device *pdev) +{ + struct device_node *child, *np = pdev->dev.of_node; + struct ltq_rcu_usb2_priv *priv; + struct phy_provider *provider; + int ret; + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), + GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->dev = &pdev->dev; + dev_set_drvdata(priv->dev, priv); + + ret = ltq_rcu_usb2_of_probe(np, priv); + if (ret) + return ret; + + priv->phy = devm_phy_create(&pdev->dev, child, + <q_rcu_usb2_phy_ops); + if (IS_ERR(priv->phy)) { + dev_err(&pdev->dev, "failed to create PHY\n"); + return PTR_ERR(priv->phy); + } + + phy_set_drvdata(priv->phy, priv); + + ltq_rcu_usb2_start_cores(pdev); + + provider = devm_of_phy_provider_register(&pdev->dev, + of_phy_simple_xlate); + + return PTR_ERR_OR_ZERO(provider); +} + +static struct platform_driver ltq_rcu_usb2_phy_driver = { + .probe = ltq_rcu_usb2_phy_probe, + .driver = { + .name = "lantiq-rcu-usb2-phy", + .of_match_table = ltq_rcu_usb2_phy_of_match, + } +}; +module_platform_driver(ltq_rcu_usb2_phy_driver); + +MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>"); +MODULE_DESCRIPTION("Lantiq XWAY USB2 PHY driver"); +MODULE_LICENSE("GPL v2"); -- 2.11.0 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html