Add bi-directional and output-enable pin configuration properties.
bi-directional allows to specify when a pin shall operate in input and
output mode at the same time. This is particularly useful in platforms
where input and output buffers have to be manually enabled.
output-enable is just syntactic sugar to specify that a pin shall
operate in output mode, ignoring the provided argument.
This pairs with input-enable pin configuration option.
Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
---
Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt | 2 ++
drivers/pinctrl/pinconf-generic.c | 3 +++
include/linux/pinctrl/pinconf-generic.h | 3 +++
3 files changed, 8 insertions(+)
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
index bf3f7b0..f2ed458 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
@@ -222,6 +222,7 @@ bias-bus-hold - latch weakly
bias-pull-up - pull up the pin
bias-pull-down - pull down the pin
bias-pull-pin-default - use pin-default pull state
+bi-directional - pin supports simultaneous input/output operations
drive-push-pull - drive actively high and low
drive-open-drain - drive with open drain
drive-open-source - drive with open source
@@ -234,6 +235,7 @@ input-debounce - debounce mode with debound time X
power-source - select between different power supplies
low-power-enable - enable low power mode
low-power-disable - disable low power mode
+output-enable - enable output on pin regardless of output value
output-low - set the pin to output mode with low level
output-high - set the pin to output mode with high level
slew-rate - set the slew rate
diff --git a/drivers/pinctrl/pinconf-generic.c b/drivers/pinctrl/pinconf-generic.c
index ce3335a..03e6808 100644
--- a/drivers/pinctrl/pinconf-generic.c
+++ b/drivers/pinctrl/pinconf-generic.c
@@ -35,6 +35,7 @@ static const struct pin_config_item conf_items[] = {
PCONFDUMP(PIN_CONFIG_BIAS_PULL_PIN_DEFAULT,
"input bias pull to pin specific state", NULL, false),
PCONFDUMP(PIN_CONFIG_BIAS_PULL_UP, "input bias pull up", NULL, false),
+ PCONFDUMP(PIN_CONFIG_BIDIRECTIONAL, "bi-directional pin operations", NULL, false),
PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_DRAIN, "output drive open drain", NULL, false),
PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_SOURCE, "output drive open source", NULL, false),
PCONFDUMP(PIN_CONFIG_DRIVE_PUSH_PULL, "output drive push pull", NULL, false),
@@ -160,6 +161,7 @@ static const struct pinconf_generic_params dt_params[] = {
{ "bias-pull-up", PIN_CONFIG_BIAS_PULL_UP, 1 },
{ "bias-pull-pin-default", PIN_CONFIG_BIAS_PULL_PIN_DEFAULT, 1 },
{ "bias-pull-down", PIN_CONFIG_BIAS_PULL_DOWN, 1 },
+ { "bi-directional", PIN_CONFIG_BIDIRECTIONAL, 1 },
{ "drive-open-drain", PIN_CONFIG_DRIVE_OPEN_DRAIN, 0 },
{ "drive-open-source", PIN_CONFIG_DRIVE_OPEN_SOURCE, 0 },
{ "drive-push-pull", PIN_CONFIG_DRIVE_PUSH_PULL, 0 },
@@ -172,6 +174,7 @@ static const struct pinconf_generic_params dt_params[] = {
{ "input-schmitt-enable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 1 },
{ "low-power-disable", PIN_CONFIG_LOW_POWER_MODE, 0 },
{ "low-power-enable", PIN_CONFIG_LOW_POWER_MODE, 1 },
+ { "output-enable", PIN_CONFIG_OUTPUT, 1, },
{ "output-high", PIN_CONFIG_OUTPUT, 1, },
{ "output-low", PIN_CONFIG_OUTPUT, 0, },
{ "power-source", PIN_CONFIG_POWER_SOURCE, 0 },
diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h
index 7620eb1..279e3c5 100644
--- a/include/linux/pinctrl/pinconf-generic.h
+++ b/include/linux/pinctrl/pinconf-generic.h
@@ -42,6 +42,8 @@
* @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high
* impedance to VDD). If the argument is != 0 pull-up is enabled,
* if it is 0, pull-up is total, i.e. the pin is connected to VDD.
+ * @PIN_CONFIG_BIDIRECTIONAL: the pin will be configured to allow simultaneous
+ * input and output operations.
* @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open
* collector) which means it is usually wired with other output ports
* which are then pulled up with an external resistor. Setting this
@@ -96,6 +98,7 @@ enum pin_config_param {
PIN_CONFIG_BIAS_PULL_DOWN,
PIN_CONFIG_BIAS_PULL_PIN_DEFAULT,
PIN_CONFIG_BIAS_PULL_UP,
+ PIN_CONFIG_BIDIRECTIONAL,
PIN_CONFIG_DRIVE_OPEN_DRAIN,
PIN_CONFIG_DRIVE_OPEN_SOURCE,
PIN_CONFIG_DRIVE_PUSH_PULL,
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
