[PATCH V12 0/4] thermal: bcm2835: add thermal driver for bcm2835 SoC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




This is an attempt to finish Martin's great work on the bcm2835
thermal driver. It includes now all Eduardo's suggestions and the
explanations from the Raspberry Pi forum [1].

ChangeLog:
V1 -> V2: added specific settings depending on compatiblity
added trip point based on register
setting up ctrl-register if HW is not enabled by firmware
as per recommendation of Eric (untested)
check that clock frequency is in range
(1.9 - 5MHz - as per comment in clk-bcm2835.c)
V2 -> V4: moved back to thermal (not using bcm sub-directory)
set polling interval to 1second (was 0ms, so interrupt driven)
V5 -> V6: added correct depends in KConfig
removed defined default for RESET_DELAY
removed obvious comments
clarify HW setup comments if not set up by FW already
move clk_prepare_enable to an earlier stage and add error handling
clarify warning when TS-clock runs out of recommended range
clk_disable_unprepare added in bcm2835_thermal_remove
added comment on recommended temperature ranges for SOC
V6 -> V7: removed depends on ARCH_BCM2836 || ARCH_BCM2837 in Kconfig
V7 -> V8: rebased
V8 -> V9: moved to use the thermal framework offset and slope in
thermal_zone_parameters as per request
V9 -> V10: implement support for thermal zone descriptor, define offset and
slope within DT, apply forum explanations, replace symbolic with octal
permissions
V10 -> V11: fix parse issue in bcm2837.dtsi, fix probing and remove unused tzp
V11 -> V12: split of-thermal changes from this series since they aren't
necessary, avoid double definition of matching table

[1] - https://www.raspberrypi.org/forums/viewtopic.php?f=72&t=160289&p=1040448

Stefan Wahren (4):
  dt-bindings: Add thermal zone to bcm2835-thermal example
  ARM: dts: bcm283x: Add CPU thermal zone with 1 trip point
  ARM64: dts: bcm2837: Define CPU thermal coefficients
  thermal: bcm2835: add thermal driver for bcm2835 SoC

 .../bindings/thermal/brcm,bcm2835-thermal.txt      |   32 +-
 arch/arm/boot/dts/bcm2835.dtsi                     |    4 +
 arch/arm/boot/dts/bcm2836.dtsi                     |    4 +
 arch/arm/boot/dts/bcm283x.dtsi                     |   21 ++
 arch/arm64/boot/dts/broadcom/bcm2837.dtsi          |    4 +
 drivers/thermal/Kconfig                            |    8 +
 drivers/thermal/Makefile                           |    1 +
 drivers/thermal/bcm2835_thermal.c                  |  314 ++++++++++++++++++++
 8 files changed, 384 insertions(+), 4 deletions(-)
 create mode 100644 drivers/thermal/bcm2835_thermal.c

-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux