Add the bindings for the pinmux functions in the
ARTPEC-6 SoC, including bias and drive strength.
Signed-off-by: Jesper Nilsson <jesper.nilsson@xxxxxxxx>
---
.../bindings/pinctrl/axis,artpec6-pinctrl.txt | 85 ++++++++++++++++++++++
MAINTAINERS | 1 +
2 files changed, 86 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/axis,artpec6-pinctrl.txt
diff --git a/Documentation/devicetree/bindings/pinctrl/axis,artpec6-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/axis,artpec6-pinctrl.txt
new file mode 100644
index 0000000..47284f8
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/axis,artpec6-pinctrl.txt
@@ -0,0 +1,85 @@
+Axis ARTPEC-6 Pin Controller
+
+Required properties:
+- compatible: "axis,artpec6-pinctrl".
+- reg: Should contain the register physical address and length for the pin
+ controller.
+
+A pinctrl node should contain at least one subnode representing the pinctrl
+groups available on the machine. Each subnode will list the mux function
+required and what pin group it will use. Each subnode will also configure the
+drive strength and bias pullup of the pin group. If either of these options is
+not set, its actual value will be unspecified.
+
+
+Required subnode-properties:
+- function: Function to mux.
+- groups: Name of the pin group to use for the function above.
+
+ Available functions and groups (function: group0, group1...):
+ gpio: cpuclkoutgrp0, udlclkoutgrp0, i2c1grp0, i2c2grp0,
+ i2c3grp0, i2s0grp0, i2s1grp0, i2srefclkgrp0, spi0grp0,
+ spi1grp0, pciedebuggrp0, uart0grp0, uart0grp1, uart1grp0,
+ uart2grp0, uart2grp1, uart3grp0, uart4grp0, uart5grp0
+ cpuclkout: cpuclkoutgrp0
+ udlclkout: udlclkoutgrp0
+ i2c1: i2c1grp0
+ i2c2: i2c2grp0
+ i2c3: i2c3grp0
+ i2s0: i2s0grp0
+ i2s1: i2s1grp0
+ i2srefclk: i2srefclkgrp0
+ spi0: spi0grp0
+ spi1: spi1grp0
+ pciedebug: pciedebuggrp0
+ uart0: uart0grp0, uart0grp1
+ uart1: uart1grp0
+ uart2: uart2grp0, uart2grp1
+ uart3: uart3grp0
+ uart4: uart4grp0
+ uart5: uart5grp0
+ nand: nandgrp0
+ sdio0: sdio0grp0
+ sdio1: sdio1grp0
+ ethernet: ethernetgrp0
+
+
+Optional subnode-properties (see pinctrl-bindings.txt):
+- drive-strength: 4, 6, 8, 9 mA. For SD and NAND pins, this is for 3.3V VCCQ3.
+- bias-pull-up
+- bias-disable
+
+Examples:
+pinctrl@f801d000 {
+ compatible = "axis,artpec6-pinctrl";
+ reg = <0xf801d000 0x400>;
+
+ pinctrl_uart0: uart0grp {
+ function = "uart0";
+ groups = "uart0grp0";
+ drive-strength = <4>;
+ bias-pull-up;
+ };
+ pinctrl_uart3: uart3grp {
+ function = "uart3";
+ groups = "uart3grp0";
+ };
+};
+uart0: uart@f8036000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0xf8036000 0x1000>;
+ interrupts = <0 104 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pll2div24>, <&apb_pclk>;
+ clock-names = "uart_clk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0>;
+};
+uart3: uart@f8039000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0xf8039000 0x1000>;
+ interrupts = <0 128 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pll2div24>, <&apb_pclk>;
+ clock-names = "uart_clk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+};
diff --git a/MAINTAINERS b/MAINTAINERS
index 1b0a87f..7563bd6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1088,6 +1088,7 @@ L: linux-arm-kernel@xxxxxxxx
F: arch/arm/mach-artpec
F: arch/arm/boot/dts/artpec6*
F: drivers/clk/axis
+F: Documentation/devicetree/bindings/pinctrl/axis,artpec6-pinctrl.txt
ARM/ASPEED MACHINE SUPPORT
M: Joel Stanley <joel@xxxxxxxxx>
--
2.1.4
/^JN - Jesper Nilsson
--
Jesper Nilsson -- jesper.nilsson@xxxxxxxx
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
