The spi_nor{} is cloned from the m25p{}.
The spi_nor{} can be used by both the m25p80 and spi-nor controller.
We also add the spi_nor_xfer_cfg{} which can be used by the two
fundamental primitives: read_xfer/write_xfer.
1) the hooks for spi_nor{}:
@prepare/unpreare: used to do some work before or after the
read/write/erase/lock/unlock.
@read_xfer/write_xfer: We can use these two hooks to code all
the following hooks if the driver tries to implement them
by itself.
@read_reg: used to read the registers, such as read status register,
read configure register.
@write_reg: used to write the registers, such as write enable,
erase sector.
@read_id: read out the ID info.
@wait_till_ready: wait till the NOR becomes ready.
@read: read out the data from the NOR.
@write: write data to the NOR.
@erase: erase a sector of the NOR.
2) Add a new field sst_write_second for the SST NOR write.
Signed-off-by: Huang Shijie <b32955@xxxxxxxxxxxxx>
---
include/linux/mtd/spi-nor.h | 109 +++++++++++++++++++++++++++++++++++++++++++
1 files changed, 109 insertions(+), 0 deletions(-)
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index ab2ea1e..f3d04ba 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -50,4 +50,113 @@
/* Configuration Register bits. */
#define CR_QUAD_EN_SPAN 0x2 /* Spansion Quad I/O */
+enum read_mode {
+ SPI_NOR_NORMAL = 0,
+ SPI_NOR_FAST,
+ SPI_NOR_QUAD,
+};
+
+/**
+ * struct spi_nor_xfer_cfg - Structure for defining a Serial Flash transfer
+ * @wren: command for "Write Enable", or 0x00 for not required
+ * @cmd: command for operation
+ * @cmd_pins: number of pins to send @cmd (1, 2, 4)
+ * @addr: address for operation
+ * @addr_pins: number of pins to send @addr (1, 2, 4)
+ * @addr_width: number of address bytes
+ * (3,4, or 0 for address not required)
+ * @mode: mode data
+ * @mode_pins: number of pins to send @mode (1, 2, 4)
+ * @mode_cycles: number of mode cycles (0 for mode not required)
+ * @dummy_cycles: number of dummy cycles (0 for dummy not required)
+ */
+struct spi_nor_xfer_cfg {
+ u8 wren;
+ u8 cmd;
+ u8 cmd_pins;
+ u32 addr;
+ u8 addr_pins;
+ u8 addr_width;
+ u8 mode;
+ u8 mode_pins;
+ u8 mode_cycles;
+ u8 dummy_cycles;
+};
+
+#define SPI_NOR_MAX_CMD_SIZE 8
+enum spi_nor_ops {
+ SPI_NOR_OPS_READ = 0,
+ SPI_NOR_OPS_WRITE,
+ SPI_NOR_OPS_ERASE,
+ SPI_NOR_OPS_LOCK,
+ SPI_NOR_OPS_UNLOCK,
+};
+
+/**
+ * struct spi_nor - Structure for defining a the SPI NOR layer
+ * @mtd: point to a mtd_info structure
+ * @lock: the lock for the read/write/erase/lock/unlock operations
+ * @dev: point to a spi device, or a spi nor controller device.
+ * @page_size: the page size of the SPI NOR
+ * @addr_width: number of address bytes
+ * @erase_opcode: the opcode for erasing a sector
+ * @read_opcode: the read opcode
+ * @read_dummy: the dummy needed by the read operation
+ * @program_opcode: the program opcode
+ * @flash_read: the mode of the read
+ * @sst_write_second: used by the SST write operation
+ * @cfg: used by the read_xfer/write_xfer
+ * @cmd_buf: used by the write_reg
+ * @prepare: [OPTIONAL] do some preparations for the
+ * read/write/erase/lock/unlock operations
+ * @unprepare: [OPTIONAL] do some post work after the
+ * read/write/erase/lock/unlock operations
+ * @read_xfer: [OPTIONAL] the read fundamental primitive
+ * @write_xfer: [OPTIONAL] the writefundamental primitive
+ * @read_reg: [DRIVER-SPECIFIC] read out the register
+ * @write_reg: [DRIVER-SPECIFIC] write data to the register
+ * @read_id: [REPLACEABLE] read out the ID data, and find
+ * the proper spi_device_id
+ * @wait_till_ready: [REPLACEABLE] wait till the NOR becomes ready
+ * @read: [DRIVER-SPECIFIC] read data from the SPI NOR
+ * @write: [DRIVER-SPECIFIC] write data to the SPI NOR
+ * @erase: [DRIVER-SPECIFIC] erase a sector of the SPI NOR
+ * at the offset @offs
+ * @priv: the private data
+ */
+struct spi_nor {
+ struct mtd_info *mtd;
+ struct mutex lock;
+ struct device *dev;
+ u32 page_size;
+ u8 addr_width;
+ u8 erase_opcode;
+ u8 read_opcode;
+ u8 read_dummy;
+ u8 program_opcode;
+ enum read_mode flash_read;
+ bool sst_write_second;
+ struct spi_nor_xfer_cfg cfg;
+ u8 cmd_buf[SPI_NOR_MAX_CMD_SIZE];
+
+ int (*prepare)(struct spi_nor *nor, enum spi_nor_ops ops);
+ void (*unprepare)(struct spi_nor *nor, enum spi_nor_ops ops);
+ int (*read_xfer)(struct spi_nor *nor, struct spi_nor_xfer_cfg *cfg,
+ u8 *buf, size_t len);
+ int (*write_xfer)(struct spi_nor *nor, struct spi_nor_xfer_cfg *cfg,
+ u8 *buf, size_t len);
+ int (*read_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len);
+ int (*write_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len,
+ int write_enable);
+ const struct spi_device_id *(*read_id)(struct spi_nor *nor);
+ int (*wait_till_ready)(struct spi_nor *nor);
+
+ int (*read)(struct spi_nor *nor, loff_t from,
+ size_t len, size_t *retlen, u_char *read_buf);
+ void (*write)(struct spi_nor *nor, loff_t to,
+ size_t len, size_t *retlen, const u_char *write_buf);
+ int (*erase)(struct spi_nor *nor, loff_t offs);
+
+ void *priv;
+};
#endif
--
1.7.2.rc3
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
