From: Hans Verkuil <hans.verkuil@xxxxxxxxx>
This patch series converts the soc-camera atmel-isi to a standalone V4L2
driver.
The same is done for the ov7670 and ov2640 sensor drivers: the ov7670 was
used to test the atmel-isi driver. The ov2640 is needed because the em28xx
driver has a soc_camera include dependency. Both ov7670 and ov2640 sensors
have been tested with the atmel-isi driver.
The first 5 patches improve the ov7670 sensor driver, mostly adding modern
features such as DT support.
The next three convert the atmel-isi and move it out of soc_camera.
The following 6 patches convert ov2640 and drop the soc_camera dependency
in em28xx. I have tested that this works with my 'SpeedLink Vicious And
Divine Laplace webcam'.
The last two patches add isi support to the DT: the first for the ov7670
sensor, the second modifies it for the ov2640 sensor.
These two final patches are for demonstration purposes only, I do not plan
on merging them.
Tested with my sama5d3-Xplained board, the ov2640 sensor and two ov7670
sensors: one with and one without reset/pwdn pins. Also tested with my
em28xx-based webcam.
I'd like to get this in for 4.12. Fingers crossed.
Regards,
Hans
Changes since v4:
- the ov2640 colorspace fixes were inexplicably part of an atmel-isi patch.
Split it off as a separate patch.
- add V4L2_SUBDEV_FL_HAS_DEVNODE to ov2640.
- drop #if defined(CONFIG_MEDIA_CONTROLLER) guard around media_entity_cleanup
in ov2640.
Changes since v3:
- ov2640/ov7670: call clk_disable_unprepare where needed. I assumed this was
done by the devm_clk_get cleanup, but that wasn't the case.
- bindings: be even more explicit about which properties are mandatory.
- ov2640/ov7670: drop unused bus-width from the dts binding examples and from
the actual dts patches.
Changes since v2:
- Incorporated Sakari's and Rob's device tree bindings comments.
- ov2640: dropped the reset/power changes. These actually broke the em28xx
and there was really nothing wrong with it.
- merged the "ov2640: allow use inside em28xx" into patches 10 and 11.
It really shouldn't have been a separate patch in the first place.
- rebased on top of 4.11-rc1.
Changes since v1:
- Dropped MC support from atmel-isi and ov7670: not needed to make this
work. Only for the ov2640 was it kept since the em28xx driver requires it.
- Use devm_clk_get instead of clk_get.
- The ov7670 lower limit of the clock speed is 10 MHz instead of 12. Adjust
accordingly.
Hans Verkuil (16):
ov7670: document device tree bindings
ov7670: call v4l2_async_register_subdev
ov7670: fix g/s_parm
ov7670: get xclk
ov7670: add devicetree support
atmel-isi: document device tree bindings
atmel-isi: remove dependency of the soc-camera framework
atmel-isi: move out of soc_camera to atmel
ov2640: fix colorspace handling
ov2640: update bindings
ov2640: convert from soc-camera to a standard subdev sensor driver.
ov2640: use standard clk and enable it.
ov2640: add MC support
em28xx: drop last soc_camera link
sama5d3 dts: enable atmel-isi
at91-sama5d3_xplained.dts: select ov2640
.../devicetree/bindings/media/atmel-isi.txt | 96 +-
.../devicetree/bindings/media/i2c/ov2640.txt | 23 +-
.../devicetree/bindings/media/i2c/ov7670.txt | 43 +
MAINTAINERS | 1 +
arch/arm/boot/dts/at91-sama5d3_xplained.dts | 59 +-
arch/arm/boot/dts/sama5d3.dtsi | 4 +-
drivers/media/i2c/Kconfig | 11 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/{soc_camera => }/ov2640.c | 149 +--
drivers/media/i2c/ov7670.c | 75 +-
drivers/media/i2c/soc_camera/Kconfig | 6 -
drivers/media/i2c/soc_camera/Makefile | 1 -
drivers/media/platform/Makefile | 1 +
drivers/media/platform/atmel/Kconfig | 11 +-
drivers/media/platform/atmel/Makefile | 1 +
drivers/media/platform/atmel/atmel-isi.c | 1384 ++++++++++++++++++++
.../platform/{soc_camera => atmel}/atmel-isi.h | 0
drivers/media/platform/soc_camera/Kconfig | 11 -
drivers/media/platform/soc_camera/Makefile | 1 -
drivers/media/platform/soc_camera/atmel-isi.c | 1167 -----------------
drivers/media/usb/em28xx/em28xx-camera.c | 9 -
21 files changed, 1687 insertions(+), 1367 deletions(-)
create mode 100644 Documentation/devicetree/bindings/media/i2c/ov7670.txt
rename drivers/media/i2c/{soc_camera => }/ov2640.c (92%)
create mode 100644 drivers/media/platform/atmel/atmel-isi.c
rename drivers/media/platform/{soc_camera => atmel}/atmel-isi.h (100%)
delete mode 100644 drivers/media/platform/soc_camera/atmel-isi.c
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
