This patch adds documentation for a new "phy-handle" property,
"fixed-link" and "mdio" sub-node. These allows the enumeration
of PHYs which are supported by the phy library under drivers/net/phy.
The EMAC ethernet controller in IBM and AMCC 4xx chips is
currently stuck with a few privately defined phy
implementations. It has no support for PHYs which
are supported by the generic phylib.
Acked-by: Rob Herring <robh@xxxxxxxxxx>
Signed-off-by: Christian Lamparter <chunkeey@xxxxxxxxxxxxxx>
---
I rewrote the "phy-handle" property in order to make the
links to net/ethernet.txt consistent with the ones in the mdio
subnode. I've also added the "fixed-link" subnode, which I
copied from net/dsa.txt. I hope this doesn't invalidate Rob's
ACK from the RFC (If it does, please tell me, otherwise I
assume everything is still OK).
---
.../devicetree/bindings/powerpc/4xx/emac.txt | 64 +++++++++++++++++++++-
1 file changed, 62 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt
index 712baf6c3e24..1893b4c4d93b 100644
--- a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt
+++ b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt
@@ -71,6 +71,9 @@
For Axon it can be absent, though my current driver
doesn't handle phy-address yet so for now, keep
0x00ffffff in it.
+ - phy-handle : Used to describe configurations where a external PHY
+ is used. Please refer to:
+ Documentation/devicetree/bindings/net/ethernet.txt
- rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec
operations (if absent the value is the same as
rx-fifo-size). For Axon, either absent or 2048.
@@ -81,8 +84,22 @@
offload, phandle of the TAH device node.
- tah-channel : 1 cell, optional. If appropriate, channel used on the
TAH engine.
+ - fixed-link : Fixed-link subnode describing a link to a non-MDIO
+ managed entity. See
+ Documentation/devicetree/bindings/net/fixed-link.txt
+ for details.
+ - mdio subnode : When the EMAC has a phy connected to its local
+ mdio, which us supported by the kernel's network
+ PHY library in drivers/net/phy, there must be device
+ tree subnode with the following required properties:
+ - #address-cells: Must be <1>.
+ - #size-cells: Must be <0>.
- Example:
+ For PHY definitions: Please refer to
+ Documentation/devicetree/bindings/net/phy.txt and
+ Documentation/devicetree/bindings/net/ethernet.txt
+
+ Examples:
EMAC0: ethernet@40000800 {
device_type = "network";
@@ -104,6 +121,50 @@
zmii-channel = <0>;
};
+ EMAC1: ethernet@ef600c00 {
+ device_type = "network";
+ compatible = "ibm,emac-apm821xx", "ibm,emac4sync";
+ interrupt-parent = <&EMAC1>;
+ interrupts = <0 1>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = <0 &UIC2 0x10 IRQ_TYPE_LEVEL_HIGH /* Status */
+ 1 &UIC2 0x14 IRQ_TYPE_LEVEL_HIGH /* Wake */>;
+ reg = <0xef600c00 0x000000c4>;
+ local-mac-address = [000000000000]; /* Filled in by U-Boot */
+ mal-device = <&MAL0>;
+ mal-tx-channel = <0>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <9000>;
+ rx-fifo-size = <16384>;
+ tx-fifo-size = <2048>;
+ fifo-entry-size = <10>;
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ phy-map = <0x00000000>;
+ rgmii-device = <&RGMII0>;
+ rgmii-channel = <0>;
+ tah-device = <&TAH0>;
+ tah-channel = <0>;
+ has-inverted-stacr-oc;
+ has-new-stacr-staopc;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+
+ qca,ar8327-initvals = <
+ 0x0010 0x40000000>;
+ };
+ };
+
+
ii) McMAL node
Required properties:
@@ -145,4 +206,3 @@
- revision : as provided by the RGMII new version register if
available.
For Axon: 0x0000012a
-
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
