This patch adds a driver for configuration of the Microchip USB251xB/xBi USB 2.0 hub controller series with USB 2.0 upstream connectivity, SMBus configuration interface and two to four USB 2.0 downstream ports. Furthermore add myself as a maintainer for this driver. The datasheet can be found at the manufacturers website, see [1]. All device-tree exposed configuration features have been tested on a i.MX6 platform with a USB2512B hub. [1] http://ww1.microchip.com/downloads/en/DeviceDoc/00001692C.pdf Signed-off-by: Richard Leitner <richard.leitner@xxxxxxxxxxx> --- CHANGES v5: - Put includes in alphabetical order - Fix some indentations - Replace {set,clr}_bit_in_byte with BIT() macros - Fix multiline comments - Use of_property_read_u32() instead of of_get_property() where possible - Use min_t() instead of by-hand implemented if's - Use strlcpy and ternary operator instead of strncpy in if/else - Remove useless & improve some other outputs - Omit i2c remove function - Use module_i2c_driver() instead of module_{init,exit}() CHANGES v4: - use utf8s_to_utf16s() instead of ascii2utf16le() - remove ascii2utf16le() in lib/string.c again - remove changes in drivers/usb/core/hcd.c again (I will post a separate patch for using utf8s_to_utf16s() in there too) CHANGES v3: - move ascii2utf16le() to lib/string.c and also use it also for ascii2desc in drivers/usb/core/hcd.c - remove platform data support from usb251xb driver CHANGES v2: - fix max-{b,s}p-current property name - add descriptor string handling from platform_data - fix non-dt handling --- Documentation/devicetree/bindings/usb/usb251xb.txt | 83 +++ MAINTAINERS | 8 + drivers/usb/misc/Kconfig | 9 + drivers/usb/misc/Makefile | 1 + drivers/usb/misc/usb251xb.c | 605 +++++++++++++++++++++ 5 files changed, 706 insertions(+) create mode 100644 Documentation/devicetree/bindings/usb/usb251xb.txt create mode 100644 drivers/usb/misc/usb251xb.c diff --git a/Documentation/devicetree/bindings/usb/usb251xb.txt b/Documentation/devicetree/bindings/usb/usb251xb.txt new file mode 100644 index 0000000..0c065f7 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb251xb.txt @@ -0,0 +1,83 @@ +Microchip USB 2.0 Hi-Speed Hub Controller + +The device node for the configuration of a Microchip USB251xB/xBi USB 2.0 +Hi-Speed Controller. + +Required properties : + - compatible : Should be "microchip,usb251xb" or one of the specific types: + "microchip,usb2512b", "microchip,usb2512bi", "microchip,usb2513b", + "microchip,usb2513bi", "microchip,usb2514b", "microchip,usb2514bi" + - hub-reset-gpios : Should specify the gpio for hub reset + +Optional properties : + - reg : I2C address on the selected bus (default is <0x2C>) + - skip-config : Skip Hub configuration, but only send the USB-Attach command + - vendor-id : USB Vendor ID of the hub (16 bit, default is 0x0424) + - product-id : USB Product ID of the hub (16 bit, default depends on type) + - device-id : USB Device ID of the hub (16 bit, default is 0x0bb3) + - language-id : USB Language ID (16 bit, default is 0x0000) + - manufacturer : USB Manufacturer string (max 31 characters long) + - product : USB Product string (max 31 characters long) + - serial : USB Serial string (max 31 characters long) + - {bus,self}-powered : selects between self- and bus-powered operation (default + is self-powered) + - disable-hi-speed : disable USB Hi-Speed support + - {multi,single}-tt : selects between multi- and single-transaction-translator + (default is multi-tt) + - disable-eop : disable End of Packet generation in full-speed mode + - {ganged,individual}-sensing : select over-current sense type in self-powered + mode (default is individual) + - {ganged,individual}-port-switching : select port power switching mode + (default is individual) + - dynamic-power-switching : enable auto-switching from self- to bus-powered + operation if the local power source is removed or unavailable + - oc-delay-{100us,4ms,8ms,16ms} : set over current timer delay (default is 8ms) + - compound-device : indicated the hub is part of a compound device + - port-mapping-mode : enable port mapping mode + - string-support : enable string descriptor support (required for manufacturer, + product and serial string configuration) + - non-removable-ports : Should specify the ports which have a non-removable + device connected. + - sp-disabled-ports : Specifies the ports which will be self-power disabled + - bp-disabled-ports : Specifies the ports which will be bus-power disabled + - max-sp-power : Specifies the maximum current the hub consumes from an + upstream port when operating as self-powered hub including the power + consumption of a permanently attached peripheral if the hub is + configured as a compound device. The value is given in mA in a 0 - 500 + range (default is 2). + - max-bp-power : Specifies the maximum current the hub consumes from an + upstream port when operating as bus-powered hub including the power + consumption of a permanently attached peripheral if the hub is + configured as a compound device. The value is given in mA in a 0 - 500 + range (default is 100). + - max-sp-current : Specifies the maximum current the hub consumes from an + upstream port when operating as self-powered hub EXCLUDING the power + consumption of a permanently attached peripheral if the hub is + configured as a compound device. The value is given in mA in a 0 - 500 + range (default is 2). + - max-bp-current : Specifies the maximum current the hub consumes from an + upstream port when operating as bus-powered hub EXCLUDING the power + consumption of a permanently attached peripheral if the hub is + configured as a compound device. The value is given in mA in a 0 - 500 + range (default is 100). + - power-on-time : Specifies the time it takes from the time the host initiates + the power-on sequence to a port until the port has adequate power. The + value is given in ms in a 0 - 510 range (default is 100ms). + +Examples: + usb2512b@2c { + compatible = "microchip,usb2512b"; + hub-reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + }; + + usb2514b@2c { + compatible = "microchip,usb2514b"; + reg = <0x2c>; + reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + vendor-id = /bits/ 16 <0x0000>; + product-id = /bits/ 16 <0x0000>; + string-support; + manufacturer = "Foo"; + product = "Foo-Bar"; + serial = "1234567890A"; + }; diff --git a/MAINTAINERS b/MAINTAINERS index 107c10e..ecc139b 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -8201,6 +8201,14 @@ F: drivers/media/platform/atmel/atmel-isc.c F: drivers/media/platform/atmel/atmel-isc-regs.h F: devicetree/bindings/media/atmel-isc.txt +MICROCHIP USB251XB DRIVER +M: Richard Leitner <richard.leitner@xxxxxxxxxxx> +L: linux-usb@xxxxxxxxxxxxxxx +S: Maintained +F: drivers/usb/misc/usb251xb.c +F: include/linux/platform_data/usb251xb.h +F: Documentation/devicetree/bindings/usb/usb251xb.txt + MICROSOFT SURFACE PRO 3 BUTTON DRIVER M: Chen Yu <yu.c.chen@xxxxxxxxx> L: platform-driver-x86@xxxxxxxxxxxxxxx diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig index 47b3577..1d1d70d 100644 --- a/drivers/usb/misc/Kconfig +++ b/drivers/usb/misc/Kconfig @@ -233,6 +233,15 @@ config USB_EZUSB_FX2 Say Y here if you need EZUSB device support. (Cypress FX/FX2/FX2LP microcontrollers) +config USB_HUB_USB251XB + tristate "USB251XB Hub Controller Configuration Driver" + depends on I2C + help + This option enables support for configuration via SMBus of the + Microchip USB251xB/xBi USB 2.0 Hub Controller series. + Configuration parameters may be set in devicetree or platform data. + Say Y or M here if you need to configure such a device via SMBus. + config USB_HSIC_USB3503 tristate "USB3503 HSIC to USB20 Driver" depends on I2C diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile index 3d19927..f6ac6c9 100644 --- a/drivers/usb/misc/Makefile +++ b/drivers/usb/misc/Makefile @@ -23,6 +23,7 @@ obj-$(CONFIG_USB_TRANCEVIBRATOR) += trancevibrator.o obj-$(CONFIG_USB_USS720) += uss720.o obj-$(CONFIG_USB_SEVSEG) += usbsevseg.o obj-$(CONFIG_USB_YUREX) += yurex.o +obj-$(CONFIG_USB_HUB_USB251XB) += usb251xb.o obj-$(CONFIG_USB_HSIC_USB3503) += usb3503.o obj-$(CONFIG_USB_HSIC_USB4604) += usb4604.o obj-$(CONFIG_USB_CHAOSKEY) += chaoskey.o diff --git a/drivers/usb/misc/usb251xb.c b/drivers/usb/misc/usb251xb.c new file mode 100644 index 0000000..4e18600 --- /dev/null +++ b/drivers/usb/misc/usb251xb.c @@ -0,0 +1,605 @@ +/* + * Driver for Microchip USB251xB USB 2.0 Hi-Speed Hub Controller + * Configuration via SMBus. + * + * Copyright (c) 2017 SKIDATA AG + * + * This work is based on the USB3503 driver by Dongjin Kim and + * a not-accepted patch by Fabien Lahoudere, see: + * https://patchwork.kernel.org/patch/9257715/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/i2c.h> +#include <linux/module.h> +#include <linux/nls.h> +#include <linux/of_device.h> +#include <linux/of_gpio.h> +#include <linux/slab.h> + +/* Internal Register Set Addresses & Default Values acc. to DS00001692C */ +#define USB251XB_ADDR_VENDOR_ID_LSB 0x00 +#define USB251XB_ADDR_VENDOR_ID_MSB 0x01 +#define USB251XB_DEF_VENDOR_ID 0x0424 + +#define USB251XB_ADDR_PRODUCT_ID_LSB 0x02 +#define USB251XB_ADDR_PRODUCT_ID_MSB 0x03 +#define USB251XB_DEF_PRODUCT_ID_12 0x2512 /* USB2512B/12Bi */ +#define USB251XB_DEF_PRODUCT_ID_13 0x2513 /* USB2513B/13Bi */ +#define USB251XB_DEF_PRODUCT_ID_14 0x2514 /* USB2514B/14Bi */ + +#define USB251XB_ADDR_DEVICE_ID_LSB 0x04 +#define USB251XB_ADDR_DEVICE_ID_MSB 0x05 +#define USB251XB_DEF_DEVICE_ID 0x0BB3 + +#define USB251XB_ADDR_CONFIG_DATA_1 0x06 +#define USB251XB_DEF_CONFIG_DATA_1 0x9B +#define USB251XB_ADDR_CONFIG_DATA_2 0x07 +#define USB251XB_DEF_CONFIG_DATA_2 0x20 +#define USB251XB_ADDR_CONFIG_DATA_3 0x08 +#define USB251XB_DEF_CONFIG_DATA_3 0x02 + +#define USB251XB_ADDR_NON_REMOVABLE_DEVICES 0x09 +#define USB251XB_DEF_NON_REMOVABLE_DEVICES 0x00 + +#define USB251XB_ADDR_PORT_DISABLE_SELF 0x0A +#define USB251XB_DEF_PORT_DISABLE_SELF 0x00 +#define USB251XB_ADDR_PORT_DISABLE_BUS 0x0B +#define USB251XB_DEF_PORT_DISABLE_BUS 0x00 + +#define USB251XB_ADDR_MAX_POWER_SELF 0x0C +#define USB251XB_DEF_MAX_POWER_SELF 0x01 +#define USB251XB_ADDR_MAX_POWER_BUS 0x0D +#define USB251XB_DEF_MAX_POWER_BUS 0x32 + +#define USB251XB_ADDR_MAX_CURRENT_SELF 0x0E +#define USB251XB_DEF_MAX_CURRENT_SELF 0x01 +#define USB251XB_ADDR_MAX_CURRENT_BUS 0x0F +#define USB251XB_DEF_MAX_CURRENT_BUS 0x32 + +#define USB251XB_ADDR_POWER_ON_TIME 0x10 +#define USB251XB_DEF_POWER_ON_TIME 0x32 + +#define USB251XB_ADDR_LANGUAGE_ID_HIGH 0x11 +#define USB251XB_ADDR_LANGUAGE_ID_LOW 0x12 +#define USB251XB_DEF_LANGUAGE_ID 0x0000 + +#define USB251XB_STRING_BUFSIZE 62 +#define USB251XB_ADDR_MANUFACTURER_STRING_LEN 0x13 +#define USB251XB_ADDR_MANUFACTURER_STRING 0x16 +#define USB251XB_DEF_MANUFACTURER_STRING "Microchip" + +#define USB251XB_ADDR_PRODUCT_STRING_LEN 0x14 +#define USB251XB_ADDR_PRODUCT_STRING 0x54 +#define USB251XB_DEF_PRODUCT_STRING "USB251xB/xBi" + +#define USB251XB_ADDR_SERIAL_STRING_LEN 0x15 +#define USB251XB_ADDR_SERIAL_STRING 0x92 +#define USB251XB_DEF_SERIAL_STRING "" + +#define USB251XB_ADDR_BATTERY_CHARGING_ENABLE 0xD0 +#define USB251XB_DEF_BATTERY_CHARGING_ENABLE 0x00 + +#define USB251XB_ADDR_BOOST_UP 0xF6 +#define USB251XB_DEF_BOOST_UP 0x00 +#define USB251XB_ADDR_BOOST_X 0xF8 +#define USB251XB_DEF_BOOST_X 0x00 + +#define USB251XB_ADDR_PORT_SWAP 0xFA +#define USB251XB_DEF_PORT_SWAP 0x00 + +#define USB251XB_ADDR_PORT_MAP_12 0xFB +#define USB251XB_DEF_PORT_MAP_12 0x00 +#define USB251XB_ADDR_PORT_MAP_34 0xFC +#define USB251XB_DEF_PORT_MAP_34 0x00 /* USB2513B/i & USB2514B/i only */ + +#define USB251XB_ADDR_STATUS_COMMAND 0xFF +#define USB251XB_STATUS_COMMAND_SMBUS_DOWN 0x04 +#define USB251XB_STATUS_COMMAND_RESET 0x02 +#define USB251XB_STATUS_COMMAND_ATTACH 0x01 + +#define USB251XB_I2C_REG_SZ 0x100 +#define USB251XB_I2C_WRITE_SZ 0x10 + +#define DRIVER_NAME "usb251xb" +#define DRIVER_DESC "Microchip USB 2.0 Hi-Speed Hub Controller" +#define DRIVER_VERSION "1.0" + +struct usb251xb { + struct device *dev; + struct i2c_client *i2c; + u8 skip_config; + int gpio_reset; + u16 vendor_id; + u16 product_id; + u16 device_id; + u8 conf_data1; + u8 conf_data2; + u8 conf_data3; + u8 non_rem_dev; + u8 port_disable_sp; + u8 port_disable_bp; + u8 max_power_sp; + u8 max_power_bp; + u8 max_current_sp; + u8 max_current_bp; + u8 power_on_time; + u16 lang_id; + u8 manufacturer_len; + u8 product_len; + u8 serial_len; + char manufacturer[USB251XB_STRING_BUFSIZE]; + char product[USB251XB_STRING_BUFSIZE]; + char serial[USB251XB_STRING_BUFSIZE]; + u8 bat_charge_en; + u8 boost_up; + u8 boost_x; + u8 port_swap; + u8 port_map12; + u8 port_map34; + u8 status; +}; + +struct usb251xb_data { + u16 product_id; + char product_str[USB251XB_STRING_BUFSIZE / 2]; /* ASCII string */ +}; + +static const struct usb251xb_data usb2512b_data = { + .product_id = 0x2512, + .product_str = "USB2512B", +}; + +static const struct usb251xb_data usb2512bi_data = { + .product_id = 0x2512, + .product_str = "USB2512Bi", +}; + +static const struct usb251xb_data usb2513b_data = { + .product_id = 0x2513, + .product_str = "USB2513B", +}; + +static const struct usb251xb_data usb2513bi_data = { + .product_id = 0x2513, + .product_str = "USB2513Bi", +}; + +static const struct usb251xb_data usb2514b_data = { + .product_id = 0x2514, + .product_str = "USB2514B", +}; + +static const struct usb251xb_data usb2514bi_data = { + .product_id = 0x2514, + .product_str = "USB2514Bi", +}; + +static void usb251xb_reset(struct usb251xb *hub, int state) +{ + if (!gpio_is_valid(hub->gpio_reset)) + return; + + gpio_set_value_cansleep(hub->gpio_reset, state); + + /* wait for hub recovery/stabilization */ + if (state) + usleep_range(500, 750); /* >=500us at power on */ + else + usleep_range(1, 10); /* >=1us at power down */ +} + +static int usb251xb_connect(struct usb251xb *hub) +{ + struct device *dev = hub->dev; + int err, i; + char i2c_wb[USB251XB_I2C_REG_SZ]; + + memset(i2c_wb, 0, USB251XB_I2C_REG_SZ); + + if (hub->skip_config) { + dev_info(dev, "Skip hub configuration, only attach.\n"); + i2c_wb[0] = 0x01; + i2c_wb[1] = USB251XB_STATUS_COMMAND_ATTACH; + + usb251xb_reset(hub, 1); + + err = i2c_smbus_write_i2c_block_data(hub->i2c, + USB251XB_ADDR_STATUS_COMMAND, 2, i2c_wb); + if (err) { + dev_err(dev, "attaching hub failed: %d\n", err); + return err; + } + return 0; + } + + i2c_wb[USB251XB_ADDR_VENDOR_ID_MSB] = (hub->vendor_id >> 8) & 0xFF; + i2c_wb[USB251XB_ADDR_VENDOR_ID_LSB] = hub->vendor_id & 0xFF; + i2c_wb[USB251XB_ADDR_PRODUCT_ID_MSB] = (hub->product_id >> 8) & 0xFF; + i2c_wb[USB251XB_ADDR_PRODUCT_ID_LSB] = hub->product_id & 0xFF; + i2c_wb[USB251XB_ADDR_DEVICE_ID_MSB] = (hub->device_id >> 8) & 0xFF; + i2c_wb[USB251XB_ADDR_DEVICE_ID_LSB] = hub->device_id & 0xFF; + i2c_wb[USB251XB_ADDR_CONFIG_DATA_1] = hub->conf_data1; + i2c_wb[USB251XB_ADDR_CONFIG_DATA_2] = hub->conf_data2; + i2c_wb[USB251XB_ADDR_CONFIG_DATA_3] = hub->conf_data3; + i2c_wb[USB251XB_ADDR_NON_REMOVABLE_DEVICES] = hub->non_rem_dev; + i2c_wb[USB251XB_ADDR_PORT_DISABLE_SELF] = hub->port_disable_sp; + i2c_wb[USB251XB_ADDR_PORT_DISABLE_BUS] = hub->port_disable_bp; + i2c_wb[USB251XB_ADDR_MAX_POWER_SELF] = hub->max_power_sp; + i2c_wb[USB251XB_ADDR_MAX_POWER_BUS] = hub->max_power_bp; + i2c_wb[USB251XB_ADDR_MAX_CURRENT_SELF] = hub->max_current_sp; + i2c_wb[USB251XB_ADDR_MAX_CURRENT_BUS] = hub->max_current_bp; + i2c_wb[USB251XB_ADDR_POWER_ON_TIME] = hub->power_on_time; + i2c_wb[USB251XB_ADDR_LANGUAGE_ID_HIGH] = (hub->lang_id >> 8) & 0xFF; + i2c_wb[USB251XB_ADDR_LANGUAGE_ID_LOW] = hub->lang_id & 0xFF; + i2c_wb[USB251XB_ADDR_MANUFACTURER_STRING_LEN] = hub->manufacturer_len; + i2c_wb[USB251XB_ADDR_PRODUCT_STRING_LEN] = hub->product_len; + i2c_wb[USB251XB_ADDR_SERIAL_STRING_LEN] = hub->serial_len; + memcpy(&i2c_wb[USB251XB_ADDR_MANUFACTURER_STRING], hub->manufacturer, + USB251XB_STRING_BUFSIZE); + memcpy(&i2c_wb[USB251XB_ADDR_SERIAL_STRING], hub->serial, + USB251XB_STRING_BUFSIZE); + memcpy(&i2c_wb[USB251XB_ADDR_PRODUCT_STRING], hub->product, + USB251XB_STRING_BUFSIZE); + i2c_wb[USB251XB_ADDR_BATTERY_CHARGING_ENABLE] = hub->bat_charge_en; + i2c_wb[USB251XB_ADDR_BOOST_UP] = hub->boost_up; + i2c_wb[USB251XB_ADDR_BOOST_X] = hub->boost_x; + i2c_wb[USB251XB_ADDR_PORT_SWAP] = hub->port_swap; + i2c_wb[USB251XB_ADDR_PORT_MAP_12] = hub->port_map12; + i2c_wb[USB251XB_ADDR_PORT_MAP_34] = hub->port_map34; + i2c_wb[USB251XB_ADDR_STATUS_COMMAND] = USB251XB_STATUS_COMMAND_ATTACH; + + usb251xb_reset(hub, 1); + + /* write registers */ + for (i = 0; i < (USB251XB_I2C_REG_SZ / USB251XB_I2C_WRITE_SZ); i++) { + int offset = i * USB251XB_I2C_WRITE_SZ; + char wbuf[USB251XB_I2C_WRITE_SZ + 1]; + + /* The first data byte transferred tells the hub how many data + * bytes will follow (byte count). + */ + wbuf[0] = USB251XB_I2C_WRITE_SZ; + memcpy(&wbuf[1], &i2c_wb[offset], USB251XB_I2C_WRITE_SZ); + + dev_dbg(dev, "writing %d byte block %d to 0x%02X\n", + USB251XB_I2C_WRITE_SZ, i, offset); + + err = i2c_smbus_write_i2c_block_data(hub->i2c, offset, + USB251XB_I2C_WRITE_SZ + 1, + wbuf); + if (err) + goto out_err; + } + + dev_info(dev, "Hub configuration was successful.\n"); + return 0; + +out_err: + dev_err(dev, "configuring block %d failed: %d\n", i, err); + return err; +} + +#ifdef CONFIG_OF +static int usb251xb_get_ofdata(struct usb251xb *hub, + struct usb251xb_data *data) +{ + struct device *dev = hub->dev; + struct device_node *np = dev->of_node; + int len, err, i; + u32 *property_u32 = NULL; + const u32 *cproperty_u32; + const char *cproperty_char; + char str[USB251XB_STRING_BUFSIZE / 2]; + + if (!np) { + dev_err(dev, "failed to get ofdata\n"); + return -ENODEV; + } + + if (of_get_property(np, "skip-config", NULL)) + hub->skip_config = 1; + else + hub->skip_config = 0; + + hub->gpio_reset = of_get_named_gpio(np, "reset-gpios", 0); + if (hub->gpio_reset == -EPROBE_DEFER) + return -EPROBE_DEFER; + if (gpio_is_valid(hub->gpio_reset)) { + err = devm_gpio_request_one(dev, hub->gpio_reset, + GPIOF_OUT_INIT_LOW, + "usb251xb reset"); + if (err) { + dev_err(dev, + "unable to request GPIO %d as reset pin (%d)\n", + hub->gpio_reset, err); + return err; + } + } + + if (of_property_read_u16_array(np, "vendor-id", &hub->vendor_id, 1)) + hub->vendor_id = USB251XB_DEF_VENDOR_ID; + + if (of_property_read_u16_array(np, "product-id", + &hub->product_id, 1)) + hub->product_id = data->product_id; + + if (of_property_read_u16_array(np, "device-id", &hub->device_id, 1)) + hub->device_id = USB251XB_DEF_DEVICE_ID; + + hub->conf_data1 = USB251XB_DEF_CONFIG_DATA_1; + if (of_get_property(np, "self-powered", NULL)) { + hub->conf_data1 |= BIT(7); + + /* Configure Over-Current sens when self-powered */ + hub->conf_data1 &= ~BIT(2); + if (of_get_property(np, "ganged-sensing", NULL)) + hub->conf_data1 &= ~BIT(1); + else if (of_get_property(np, "individual-sensing", NULL)) + hub->conf_data1 |= BIT(1); + } else if (of_get_property(np, "bus-powered", NULL)) { + hub->conf_data1 &= ~BIT(7); + + /* Disable Over-Current sense when bus-powered */ + hub->conf_data1 |= BIT(2); + } + + if (of_get_property(np, "disable-hi-speed", NULL)) + hub->conf_data1 |= BIT(5); + + if (of_get_property(np, "multi-tt", NULL)) + hub->conf_data1 |= BIT(4); + else if (of_get_property(np, "single-tt", NULL)) + hub->conf_data1 &= ~BIT(4); + + if (of_get_property(np, "disable-eop", NULL)) + hub->conf_data1 |= BIT(3); + + if (of_get_property(np, "individual-port-switching", NULL)) + hub->conf_data1 |= BIT(0); + else if (of_get_property(np, "ganged-port-switching", NULL)) + hub->conf_data1 &= ~BIT(0); + + hub->conf_data2 = USB251XB_DEF_CONFIG_DATA_2; + if (of_get_property(np, "dynamic-power-switching", NULL)) + hub->conf_data2 |= BIT(7); + + if (of_get_property(np, "oc-delay-100us", NULL)) { + hub->conf_data2 &= ~BIT(5); + hub->conf_data2 &= ~BIT(4); + } else if (of_get_property(np, "oc-delay-4ms", NULL)) { + hub->conf_data2 &= ~BIT(5); + hub->conf_data2 |= BIT(4); + } else if (of_get_property(np, "oc-delay-8ms", NULL)) { + hub->conf_data2 |= BIT(5); + hub->conf_data2 &= ~BIT(4); + } else if (of_get_property(np, "oc-delay-16ms", NULL)) { + hub->conf_data2 |= BIT(5); + hub->conf_data2 |= BIT(4); + } + + if (of_get_property(np, "compound-device", NULL)) + hub->conf_data2 |= BIT(3); + + hub->conf_data3 = USB251XB_DEF_CONFIG_DATA_3; + if (of_get_property(np, "port-mapping-mode", NULL)) + hub->conf_data3 |= BIT(3); + + if (of_get_property(np, "string-support", NULL)) + hub->conf_data3 |= BIT(0); + + hub->non_rem_dev = USB251XB_DEF_NON_REMOVABLE_DEVICES; + cproperty_u32 = of_get_property(np, "non-removable-ports", &len); + if (cproperty_u32 && (len / sizeof(u32)) > 0) { + for (i = 0; i < len / sizeof(u32); i++) { + u32 port = be32_to_cpu(cproperty_u32[i]); + + if ((port >= 1) && (port <= 4)) + hub->non_rem_dev |= BIT(port); + } + } + + hub->port_disable_sp = USB251XB_DEF_PORT_DISABLE_SELF; + cproperty_u32 = of_get_property(np, "sp-disabled-ports", &len); + if (cproperty_u32 && (len / sizeof(u32)) > 0) { + for (i = 0; i < len / sizeof(u32); i++) { + u32 port = be32_to_cpu(cproperty_u32[i]); + + if ((port >= 1) && (port <= 4)) + hub->port_disable_sp |= BIT(port); + } + } + + hub->port_disable_bp = USB251XB_DEF_PORT_DISABLE_BUS; + cproperty_u32 = of_get_property(np, "bp-disabled-ports", &len); + if (cproperty_u32 && (len / sizeof(u32)) > 0) { + for (i = 0; i < len / sizeof(u32); i++) { + u32 port = be32_to_cpu(cproperty_u32[i]); + + if ((port >= 1) && (port <= 4)) + hub->port_disable_bp |= BIT(port); + } + } + + hub->max_power_sp = USB251XB_DEF_MAX_POWER_SELF; + if (!of_property_read_u32(np, "max-sp-power", property_u32)) + hub->max_power_sp = min_t(u8, be32_to_cpu(*property_u32) / 2, + 250); + + hub->max_power_bp = USB251XB_DEF_MAX_POWER_BUS; + if (!of_property_read_u32(np, "max-bp-power", property_u32)) + hub->max_power_bp = min_t(u8, be32_to_cpu(*property_u32) / 2, + 250); + + hub->max_current_sp = USB251XB_DEF_MAX_CURRENT_SELF; + if (!of_property_read_u32(np, "max-sp-current", property_u32)) + hub->max_current_sp = min_t(u8, be32_to_cpu(*property_u32) / 2, + 250); + + hub->max_current_bp = USB251XB_DEF_MAX_CURRENT_BUS; + if (!of_property_read_u32(np, "max-bp-current", property_u32)) + hub->max_current_bp = min_t(u8, be32_to_cpu(*property_u32) / 2, + 250); + + hub->power_on_time = USB251XB_DEF_POWER_ON_TIME; + if (!of_property_read_u32(np, "power-on-time", property_u32)) + hub->power_on_time = min_t(u8, be32_to_cpu(*property_u32) / 2, + 255); + + if (of_property_read_u16_array(np, "language-id", &hub->lang_id, 1)) + hub->lang_id = USB251XB_DEF_LANGUAGE_ID; + + cproperty_char = of_get_property(np, "manufacturer", NULL); + strlcpy(str, cproperty_char ? : USB251XB_DEF_MANUFACTURER_STRING, + sizeof(str)); + hub->manufacturer_len = strlen(str) & 0xFF; + memset(hub->manufacturer, 0, USB251XB_STRING_BUFSIZE); + len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str)); + len = utf8s_to_utf16s(str, len, UTF16_LITTLE_ENDIAN, + (wchar_t *)hub->manufacturer, + USB251XB_STRING_BUFSIZE); + + cproperty_char = of_get_property(np, "product", NULL); + strlcpy(str, cproperty_char ? : data->product_str, sizeof(str)); + hub->product_len = strlen(str) & 0xFF; + memset(hub->product, 0, USB251XB_STRING_BUFSIZE); + len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str)); + len = utf8s_to_utf16s(str, len, UTF16_LITTLE_ENDIAN, + (wchar_t *)hub->product, + USB251XB_STRING_BUFSIZE); + + cproperty_char = of_get_property(np, "serial", NULL); + strlcpy(str, cproperty_char ? : USB251XB_DEF_SERIAL_STRING, + sizeof(str)); + hub->serial_len = strlen(str) & 0xFF; + memset(hub->serial, 0, USB251XB_STRING_BUFSIZE); + len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str)); + len = utf8s_to_utf16s(str, len, UTF16_LITTLE_ENDIAN, + (wchar_t *)hub->serial, + USB251XB_STRING_BUFSIZE); + + /* The following parameters are currently not exposed to devicetree, but + * may be as soon as needed. + */ + hub->bat_charge_en = USB251XB_DEF_BATTERY_CHARGING_ENABLE; + hub->boost_up = USB251XB_DEF_BOOST_UP; + hub->boost_x = USB251XB_DEF_BOOST_X; + hub->port_swap = USB251XB_DEF_PORT_SWAP; + hub->port_map12 = USB251XB_DEF_PORT_MAP_12; + hub->port_map34 = USB251XB_DEF_PORT_MAP_34; + + return 0; +} + +static const struct of_device_id usb251xb_of_match[] = { + { + .compatible = "microchip,usb2512b", + .data = &usb2512b_data, + }, { + .compatible = "microchip,usb2512bi", + .data = &usb2512bi_data, + }, { + .compatible = "microchip,usb2513b", + .data = &usb2513b_data, + }, { + .compatible = "microchip,usb2513bi", + .data = &usb2513bi_data, + }, { + .compatible = "microchip,usb2514b", + .data = &usb2514b_data, + }, { + .compatible = "microchip,usb2514bi", + .data = &usb2514bi_data, + }, { + /* sentinel */ + } +}; +MODULE_DEVICE_TABLE(of, usb251xb_of_match); +#else /* CONFIG_OF */ +static int usb251xb_get_ofdata(struct usb251xb *hub, + struct usb251xb_data *data) +{ + return 0; +} +#endif /* CONFIG_OF */ + +static int usb251xb_probe(struct usb251xb *hub) +{ + struct device *dev = hub->dev; + struct device_node *np = dev->of_node; + const struct of_device_id *of_id = of_match_device(usb251xb_of_match, + dev); + int err; + + if (np) { + err = usb251xb_get_ofdata(hub, + (struct usb251xb_data *)of_id->data); + if (err) { + dev_err(dev, "failed to get ofdata: %d\n", err); + return err; + } + } + + err = usb251xb_connect(hub); + if (err) { + dev_err(dev, "Failed to connect hub (%d)\n", err); + return err; + } + + dev_info(dev, "Hub probed successfully\n"); + + return 0; +} + +static int usb251xb_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id) +{ + struct usb251xb *hub; + + hub = devm_kzalloc(&i2c->dev, sizeof(struct usb251xb), GFP_KERNEL); + if (!hub) + return -ENOMEM; + + i2c_set_clientdata(i2c, hub); + hub->dev = &i2c->dev; + hub->i2c = i2c; + + return usb251xb_probe(hub); +} + +static const struct i2c_device_id usb251xb_id[] = { + { "usb2512b", 0 }, + { "usb2512bi", 0 }, + { "usb2513b", 0 }, + { "usb2513bi", 0 }, + { "usb2514b", 0 }, + { "usb2514bi", 0 }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(i2c, usb251xb_id); + +static struct i2c_driver usb251xb_i2c_driver = { + .driver = { + .name = DRIVER_NAME, + .of_match_table = of_match_ptr(usb251xb_of_match), + }, + .probe = usb251xb_i2c_probe, + .id_table = usb251xb_id, +}; + +module_i2c_driver(usb251xb_i2c_driver); + +MODULE_AUTHOR("Richard Leitner <richard.leitner@xxxxxxxxxxx>"); +MODULE_DESCRIPTION("USB251xB/xBi USB 2.0 Hub Controller Driver"); +MODULE_LICENSE("GPL"); -- 2.1.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
