Le 02/05/17 à 14:25, Christian Lamparter a écrit :
> This patch adds documentation for a new "phy-handler" property
> and "mdio" sub-node. These allows the enumeration of PHYs which
> are supported by the phy library under drivers/net/phy.
>
> The EMAC ethernet controller in IBM and AMCC 4xx chips is
> currently stuck with a few privately defined phy
> implementations. It has no support for PHYs which
> are supported by the generic phylib.
>
> Signed-off-by: Christian Lamparter <chunkeey@xxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/powerpc/4xx/emac.txt | 60 +++++++++++++++++++++-
> 1 file changed, 58 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt
> index 712baf6c3e24..0572d053c35a 100644
> --- a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt
> +++ b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt
> @@ -71,6 +71,8 @@
> For Axon it can be absent, though my current driver
> doesn't handle phy-address yet so for now, keep
> 0x00ffffff in it.
> + - phy-handle : See net/ethernet.txt file; used to describe
> + configurations where a external PHY is used.
> - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec
> operations (if absent the value is the same as
> rx-fifo-size). For Axon, either absent or 2048.
> @@ -82,7 +84,18 @@
> - tah-channel : 1 cell, optional. If appropriate, channel used on the
> TAH engine.
>
> - Example:
> + - mdio subnode : When the EMAC has a phy connected to its local
> + mdio, which us supported by the kernel's network
> + PHY library in drivers/net/phy, there must be device
> + tree subnode with the following required properties:
> + - #address-cells: Must be <1>.
> + - #size-cells: Must be <0>.
> +
> + For each phy on the mdio bus, there must be a node
> + with the following fields:
> + - reg: phy id used to communicate to phy.
> + - device_type: Must be "ethernet-phy".
Just provide a reference to
Documentation/devicetree/bindings/net/phy.txt and
Documentation/devicetree/bindings/net/ethernet.txt here. device_type is
not required.
> + Examples:
>
> EMAC0: ethernet@40000800 {
> device_type = "network";
> @@ -104,6 +117,50 @@
> zmii-channel = <0>;
> };
>
> + EMAC1: ethernet@ef600c00 {
> + device_type = "network";
> + compatible = "ibm,emac-apm821xx", "ibm,emac4sync";
> + interrupt-parent = <&EMAC1>;
> + interrupts = <0 1>;
> + #interrupt-cells = <1>;
> + #address-cells = <0>;
> + #size-cells = <0>;
> + interrupt-map = <0 &UIC2 0x10 IRQ_TYPE_LEVEL_HIGH /* Status */
> + 1 &UIC2 0x14 IRQ_TYPE_LEVEL_HIGH /* Wake */>;
> + reg = <0xef600c00 0x000000c4>;
> + local-mac-address = [000000000000]; /* Filled in by U-Boot */
> + mal-device = <&MAL0>;
> + mal-tx-channel = <0>;
> + mal-rx-channel = <0>;
> + cell-index = <0>;
> + max-frame-size = <9000>;
> + rx-fifo-size = <16384>;
> + tx-fifo-size = <2048>;
> + fifo-entry-size = <10>;
> + phy-mode = "rgmii";
> + phy-map = <0x00000000>;
If you have a proper mdio subnode, this property becomes irrelevant and
should be unused.
> + phy-handle = <&phy0>;
> + rgmii-device = <&RGMII0>;
> + rgmii-channel = <0>;
> + tah-device = <&TAH0>;
> + tah-channel = <0>;
> + has-inverted-stacr-oc;
> + has-new-stacr-staopc;
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + phy0: ethernet-phy@0 {
> + device_type = "ethernet-phy";
> + reg = <0>;
> +
> + qca,ar8327-initvals = <
> + 0x0010 0x40000000>;
> + };
> + };
> +
> +
> ii) McMAL node
>
> Required properties:
> @@ -145,4 +202,3 @@
> - revision : as provided by the RGMII new version register if
> available.
> For Axon: 0x0000012a
> -
>
--
Florian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
