From: Chris Bostic <cbostic@xxxxxxxxxx>
Define the device tree bindings for the GPIO master type.
Signed-off-by: Chris Bostic <cbostic@xxxxxxxxxx>
---
.../devicetree/bindings/fsi/fsi-master-gpio.txt | 71 ++++++++++++++++++++++
1 file changed, 71 insertions(+)
create mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt
diff --git a/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt b/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt
new file mode 100644
index 0000000..5d589bf
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt
@@ -0,0 +1,71 @@
+Device-tree bindings for FSI master implemented with GPIO
+---------------------------------------------------------
+
+Typically a FSI master is defined in hardware with output control
+lines designated for Enable, Data, Clock, etc.. In the case of
+a 'GPIO FSI master', however, it may be the case that there is no
+such master defined in hardware and must be implemented in standard
+GPIO to interact with its slaves. In this 'virtual' FSI master
+case the GPIO pins representing clk and data are directly
+connected to the slaves.
+
+The GPIO FSI master node
+-------------------------
+This node describes a FSI master implmented with GPIO.
+Required property:
+ compatible = "ibm,fsi-master-gpio"
+
+The standard FSI master node
+----------------------------
+This node describes a FSI master implmemented fully in hardware
+with dedicated input/output pins required for its function (i.e.
+not using generic GPIO pins).
+Required property:
+ compatible = "ibm,fsi-master"
+
+
+GPIO FSI master property/pin descriptions
+------------------------------------------
+clk - The master controlled clock line that indicates to the
+ slave when to read in or send out new data - required.
+data - The serial data line containing information to be sent or
+ received by the master. This line is bi-directional. During
+ command phase the master controls the line and when a response
+ is required the slave takes control - required.
+enable - Controls power state of data line - optional.
+trans - Voltage translator control. In some applications the data line
+ must have its signal levels altered by a translator. If this is
+ necessary then control of signal direction is managed via this
+ line - optional.
+mux - Multiplexor control. This activates/deactivates the data line
+ in cases where it is one of many possible selections via mux -
+ optional.
+
+Required properties:
+ - compatible = "ibm,fsi-master-gpio";
+ - clk-gpios;
+ - data-gpios;
+
+Optional properties:
+ - enable-gpios;
+ - trans-gpios;
+ - mux-gpios;
+
+Order of property activation:
+1. clk
+2. data
+3. trans
+4. enable
+5. mux
+
+
+Example:
+
+fsi-master {
+ compatible = "ibm,fsi-master-gpio", "ibm,fsi-master";
+ clk-gpios = <&gpio 0>, <&gpio 6>;
+ data-gpios = <&gpio 1>, <&gpio 7>;
+ enable-gpios = <&gpio 2>, <&gpio 8>;
+ trans-gpios = <&gpio 3>, <&gpio 9>;
+ mux-gpios = <&gpio 4>, <&gpio 10>;
+}
--
1.8.2.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
