Hi Linus,
On Sat, Jan 28, 2017 at 09:48:36PM +0100, Linus Walleij wrote:
> This adds device tree bindings for the Cortina Systems Gemini PCI
> Host Bridge.
>
> Cc: Janos Laube <janos.dev@xxxxxxxxx>
> Cc: Paulius Zaleckas <paulius.zaleckas@xxxxxxxxx>
> Cc: Hans Ulli Kroll <ulli.kroll@xxxxxxxxxxxxxx>
> Cc: Florian Fainelli <f.fainelli@xxxxxxxxx>
> Cc: devicetree@xxxxxxxxxxxxxxx
> Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
I'm hoping one of the DT folks will take a quick look at this.
> ---
> This can be merged to the PCI tree whenever it is considered
> fine for inclusion.
> ---
> .../devicetree/bindings/pci/cortina,gemini-pci.txt | 64 ++++++++++++++++++++++
> 1 file changed, 64 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pci/cortina,gemini-pci.txt
>
> diff --git a/Documentation/devicetree/bindings/pci/cortina,gemini-pci.txt b/Documentation/devicetree/bindings/pci/cortina,gemini-pci.txt
> new file mode 100644
> index 000000000000..e3090d995e1e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/cortina,gemini-pci.txt
> @@ -0,0 +1,64 @@
> +* Cortina Systems Gemini PCI Host Bridge
> +
> +Mandatory properties:
> +
> +- compatible: should be "cortina,gemini-pci"
> +- reg: memory base and size for the host bridge
> +- interrupts: the four PCI interrupts
> +- #address-cells: set to <3>
> +- #size-cells: set to <2>
> +- #interrupt-cells: set to <1>
> +- bus-range: set to <0x00 0x00> (only root bus)
Why is this limited to bus 0? Is everything completely soldered down
with no possibility of adding or replacing PCI devices? The interrupt-map
below suggests slots, though. If there's a slot, we could plug in a card
with a bridge, which would mean more than just bus 0.
> +- device_type, set to "pci"
> +- ranges: see pci.txt
> +- interrupt-map-mask: see pci.txt
> +- interrupt-map: see pci.txt
> +
> +Mandatory subnodes:
> +- One node reprenting the interrupt-controller inside the host bridge
s/reprenting/representing/
> + with the following mandatory properties:
> + - interrupt-controller: see interrupt-controller/interrupts.txt
> + - #address-cells: set to <0>
> + - #interrupt-cells: set to <1>
> +
> +Example:
> +
> +pci@50000000 {
> + compatible = "cortina,gemini-pci";
> + reg = <0x50000000 0x100>;
> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>, /* PCI A */
> + <26 IRQ_TYPE_LEVEL_HIGH>, /* PCI B */
> + <27 IRQ_TYPE_LEVEL_HIGH>, /* PCI C */
> + <28 IRQ_TYPE_LEVEL_HIGH>; /* PCI D */
> + #address-cells = <3>;
> + #size-cells = <2>;
> + #interrupt-cells = <1>;
> +
> + bus-range = <0x00 0x00>; /* Only root bus */
> + ranges = /* 1MiB I/O space 0x50000000-0x500fffff */
> + <0x01000000 0 0 0x50000000 0 0x00100000>,
> + /* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */
> + <0x02000000 0 0x58000000 0x58000000 0 0x08000000>;
> + interrupt-map-mask = <0xff00 0 0 7>;
> + interrupt-map = <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
> + <0x4900 0 0 2 &pci_intc 1>,
> + <0x4a00 0 0 3 &pci_intc 2>,
> + <0x4b00 0 0 4 &pci_intc 3>,
> + <0x5000 0 0 1 &pci_intc 0>, /* Slot 10 */
> + <0x5100 0 0 2 &pci_intc 1>,
> + <0x5200 0 0 3 &pci_intc 2>,
> + <0x5300 0 0 4 &pci_intc 3>,
> + <0x5800 0 0 1 &pci_intc 0>, /* Slot 11 */
> + <0x5900 0 0 2 &pci_intc 1>,
> + <0x5a00 0 0 3 &pci_intc 2>,
> + <0x5b00 0 0 4 &pci_intc 3>,
> + <0x6000 0 0 1 &pci_intc 0>, /* Slot 12 */
> + <0x6100 0 0 2 &pci_intc 1>,
> + <0x6200 0 0 3 &pci_intc 2>,
> + <0x6300 0 0 4 &pci_intc 3>;
> + pci_intc: interrupt-controller {
> + interrupt-controller;
> + #address-cells = <0>;
> + #interrupt-cells = <1>;
> + };
> +};
> --
> 2.9.3
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-pci" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
