Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx> writes: > On Fri, Jan 20, 2017 at 4:22 PM, Martin Blumenstingl > <martin.blumenstingl@xxxxxxxxxxxxxx> wrote: >> This series adds the reset GPIOs for the (external) ethernet PHYs on all >> GXBB boards. >> Additionally it provides a ethernet PHY node which can be used to specify >> PHY-specific properties (this may be required if more boards require the >> "eee-broken-1000t" for the RTL8211F ethernet PHY). To make all board .dts >> consistent I chose to add the PHY node also for boards which don't have a >> RTL8211F PHY. >> >> Patch #7 from this series also removes ethernet support for the P200 >> board because it was broken anyways and nobody seems to have a board >> available for testing. This was the outcome of the discussion from [0] >> >> Patch #8 was taken from (older versions of) my other series (see [1]): >> "[PATCH net-next v3 0/2] stmmac: dwmac-meson8b: configurable >> RGMII TX delay". >> The binding changes for amlogic,tx-delay-ns were ACK'ed already. >> >> Changes since v2: >> - fixed patch #2 to really update the P200 board (as it's the P200 which >> actually uses a Micrel KSZ9031 RGMII PHY). Thanks to Neil Armstrong for >> spotting this huge mistake! >> - instead of dropping ethernet support for P201 we simply re-configure it >> to RMII mode (replaces patch #7) without a MDIO node (which keeps PHY >> auto-scanning enabled). This got Neil Armstrong's ACK off-list already >> >> Changes since v1: >> - do not move the MDIO bus to meson-gx as this disables PHY auto-scanning >> in the stmmac driver (this drops patch #1 from v1) >> - add the ethernet PHY reset GPIO for nexbox a95x which was forgotten in >> v1 >> - add the ethernet PHY reset GPIO for boards which were added since v1 >> (wetek hub and wetek play2) >> - rebased to apply against the current v4.11/dt64 branch >> - new in v2 (patch #7): disabled ethernet support for the P200 board (see >> the commit description for more information). this patch is optional >> - new in v2 (patch #9): removed the phy-mode property from meson-gx (see >> the commit description for more information). this patch is optional >> >> >> [0] http://lists.infradead.org/pipermail/linux-amlogic/2017-January/002053.html >> [1] http://lists.infradead.org/pipermail/linux-amlogic/2016-December/001834.html >> >> Martin Blumenstingl (9): >> ARM64: dts: meson-gxbb-odroidc2: add the ethernet PHY's reset GPIO >> ARM64: dts: meson-gxbb-p200: add the ethernet PHY's reset GPIO >> ARM64: dts: meson-gxbb-vega-s95: add the ethernet PHY's reset GPIO >> ARM64: dts: meson-gxbb-nexbox-a95x: add the ethernet PHY's reset GPIO >> ARM64: dts: meson-gxbb-wetek-hub: add the ethernet PHY's reset GPIO >> ARM64: dts: meson-gxbb-wetek-play2: add the ethernet PHY's reset GPIO >> ARM64: dts: meson-gxbb-p201: fix ethernet support >> ARM64: dts: amlogic: add the ethernet TX delay configuration >> ARM64: dts: meson-gx: remove the phy-mode property from meson-gx >> >> arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 1 - >> .../boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 17 ++++++++++++++ >> .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 7 ++++++ >> arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts | 26 ++++++++++++++++++++++ >> arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts | 11 +++++++++ >> arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 6 ----- >> .../boot/dts/amlogic/meson-gxbb-vega-s95.dtsi | 20 +++++++++++++++++ >> .../boot/dts/amlogic/meson-gxbb-wetek-hub.dts | 26 ++++++++++++++++++++++ >> .../boot/dts/amlogic/meson-gxbb-wetek-play2.dts | 26 ++++++++++++++++++++++ >> .../boot/dts/amlogic/meson-gxl-s905d-p230.dts | 2 ++ >> .../arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 2 ++ >> arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts | 2 ++ >> 12 files changed, 139 insertions(+), 7 deletions(-) > I totally forgot to mention: > this applies to Kevin's v4.11/dt64 branch with Jerome's Odroid-C2 > ethernet fix [0] applied on top of it So when Jerome's fix lands in mainline (probably by -rc5, maybe -rc6) I'll rebase the dt64 branch on that and apply this series. Kevin -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
