Hi Hans, Philipp,
On 01/20/2017 08:31 AM, Philipp Zabel wrote:
Hi Hans,
On Fri, 2017-01-20 at 14:52 +0100, Hans Verkuil wrote:
Hi Steve, Philipp,
On 01/07/2017 03:11 AM, Steve Longerbeam wrote:
In version 3:
Changes suggested by Rob Herring <robh@xxxxxxxxxx>:
- prepended FIM node properties with vendor prefix "fsl,".
- make mipi csi-2 receiver compatible string SoC specific:
"fsl,imx6-mipi-csi2" instead of "fsl,imx-mipi-csi2".
- redundant "_clk" removed from mipi csi-2 receiver clock-names property.
- removed board-specific info from the media driver binding doc. These
were all related to sensor bindings, which already are (adv7180)
or will be (ov564x) covered in separate binding docs. All reference
board info not related to DT bindings has been moved to
Documentation/media/v4l-drivers/imx.rst.
- removed "_mipi" from the OV5640 compatible string.
Changes suggested by Vladimir Zapolskiy <vladimir_zapolskiy@xxxxxxxxxx>:
Mostly cosmetic/non-functional changes which I won't list here, except
for the following:
- spin_lock_irqsave() changed to spin_lock() in a couple interrupt handlers.
- fixed some unnecessary of_node_put()'s in for_each_child_of_node() loops.
- check/handle return code from required reg property of CSI port nodes.
- check/handle return code from clk_prepare_enable().
Changes suggested by Fabio Estevam <festevam@xxxxxxxxx>:
- switch to VGEN3 Analog Vdd supply assuming rev. C SabreSD boards.
- finally got around to passing valid IOMUX pin config values to the
pin groups.
Other changes:
- removed the FIM properties that overrided the v4l2 FIM control defaults
values. This was left-over from a requirement of a customer and is not
necessary here.
- The FIM must be explicitly enabled in the fim child node under the CSI
port nodes, using the status property. If not enabled, FIM v4l2 controls
will not appear in the video capture driver.
- brought in additional media types patch from Philipp Zabel. Use new
MEDIA_ENT_F_VID_IF_BRIDGE in mipi csi-2 receiver subdev.
- brought in latest platform generic video multiplexer subdevice driver
from Philipp Zabel (squashed with patch that uses new MEDIA_ENT_F_MUX).
- removed imx-media-of.h, moved those prototypes into imx-media.h.
Based on the discussion on the mailinglist it seems everyone agrees that this
is the preferred driver, correct?
No. I have some major reservations against the custom mem2mem framework
embedded in Steve's driver.
I think it is a misuse of the media entity links (which should describe
hardware connections) for something that should be done at the vb2 level
(letting one device's capture EOF interrupt trigger the next device's
m2m device_run without going through userspace).
Steve and I disagree on that point, so we'd appreciate if we could get
some more eyes on the above issue.
This needs some background first, so let me first describe one example
pipeline in this driver.
There is a VDIC entity in the i.MX IPU that performs de-interlacing with
hardware filters for motion compensation. Some of the motion compensation
modes ("low" and "medium" motion) require that the VDIC receive video
frame fields from memory buffers (dedicated dma channels in the
IPU are used to transfer those buffers into the VDIC).
So one option to support those modes would be to pass the raw buffers
from a camera sensor up to userspace to a capture device, and then pass
them back to the VDIC for de-interlacing using a mem2mem device.
Philipp and I are both in agreement that, since userland is not interested
in the intermediate interlaced buffers in this case, but only the final
result (motion compensated, de-interlaced frames), it is more efficient
to provide a media link that allows passing those intermediate frames
directly from a camera source pad to VDIC sink pad, without having
to route them through userspace.
So in order to support that, I've implemented a simple FIFO dma buffer
queue in the driver to allow passing video buffers directly from a source
to a sink. It is modeled loosely off the vb2 state machine and API, but
simpler (for instance it only allows contiguous, cache-coherent buffers).
This is where Philipp has an argument, that this should be done with a
new API in videobuf2.
And I'm actually in total agreement with that. I definitely agree that there
should be a mechanism in the media framework that allows passing video
buffers from a source pad to a sink pad using a software queue, with no
involvement from userland.
My only disagreement is when this should be implemented. I think it is
fine to keep my custom implementation of this in the driver for now. Once
an extension of vb2 is ready to support this feature, it would be fairly
straightforward to strip out my custom implementation and go with the
new API.
Steve
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
