Re: [PATCH v3 00/24] i.MX Media Driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Steve, Philipp,

On 01/07/2017 03:11 AM, Steve Longerbeam wrote:
> In version 3:
> 
> Changes suggested by Rob Herring <robh@xxxxxxxxxx>:
> 
>   - prepended FIM node properties with vendor prefix "fsl,".
> 
>   - make mipi csi-2 receiver compatible string SoC specific:
>     "fsl,imx6-mipi-csi2" instead of "fsl,imx-mipi-csi2".
> 
>   - redundant "_clk" removed from mipi csi-2 receiver clock-names property.
> 
>   - removed board-specific info from the media driver binding doc. These
>     were all related to sensor bindings, which already are (adv7180)
>     or will be (ov564x) covered in separate binding docs. All reference
>     board info not related to DT bindings has been moved to
>     Documentation/media/v4l-drivers/imx.rst.
> 
>   - removed "_mipi" from the OV5640 compatible string.
> 
> Changes suggested by Vladimir Zapolskiy <vladimir_zapolskiy@xxxxxxxxxx>:
> 
>   Mostly cosmetic/non-functional changes which I won't list here, except
>   for the following:
> 
>   - spin_lock_irqsave() changed to spin_lock() in a couple interrupt handlers.
> 
>   - fixed some unnecessary of_node_put()'s in for_each_child_of_node() loops.
> 
>   - check/handle return code from required reg property of CSI port nodes.
> 
>   - check/handle return code from clk_prepare_enable().
> 
> Changes suggested by Fabio Estevam <festevam@xxxxxxxxx>:
> 
>   - switch to VGEN3 Analog Vdd supply assuming rev. C SabreSD boards.
> 
>   - finally got around to passing valid IOMUX pin config values to the
>     pin groups.
> 
> Other changes:
> 
>   - removed the FIM properties that overrided the v4l2 FIM control defaults
>     values. This was left-over from a requirement of a customer and is not
>     necessary here.
> 
>   - The FIM must be explicitly enabled in the fim child node under the CSI
>     port nodes, using the status property. If not enabled, FIM v4l2 controls
>     will not appear in the video capture driver.
> 
>   - brought in additional media types patch from Philipp Zabel. Use new
>     MEDIA_ENT_F_VID_IF_BRIDGE in mipi csi-2 receiver subdev.
> 
>   - brought in latest platform generic video multiplexer subdevice driver
>     from Philipp Zabel (squashed with patch that uses new MEDIA_ENT_F_MUX).
> 
>   - removed imx-media-of.h, moved those prototypes into imx-media.h.

Based on the discussion on the mailinglist it seems everyone agrees that this
is the preferred driver, correct?

There are a bunch of review comments, so I will wait for a v4. I plan to merge
that staging driver unless there are major issues with it.

I am not sure if I would merge those sensor drivers in staging, I'll have to
take a closer look at those once v4 is posted.

Regards,

	Hans
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux