[PATCH v3 2/2] ARM: dts: imx6q: Add mccmon6 board support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




From: Lukasz Majewski <l.majewski@xxxxxxxxx>

This patch provides support for Liebherr's Monitor 6 board (abverrated as
mccmon6) to Linux kernel.

Signed-off-by: Lukasz Majewski <lukma@xxxxxxx>
---
Changes for v3:
- Reorganize the dts file according to Shawn Guo's comments

Changes for v2:
- Reorganize the dts file according to Valdimir Zapolskiy's comments

---
MCCMON6 board support depends on following patches:

1. "video: backlight: pwm_bl: Initialize fb_bl_on[x] and use_count during pwm_backlight_probe()"
	http://patchwork.ozlabs.org/patch/708844/

2. "pwm: imx: Provide atomic operation for IMX PWM driver"
	http://patchwork.ozlabs.org/patch/708847/ - http://patchwork.ozlabs.org/patch/708843/

The patch applies to v4.10-rc2
---
 arch/arm/boot/dts/Makefile          |   1 +
 arch/arm/boot/dts/imx6q-mccmon6.dts | 473 ++++++++++++++++++++++++++++++++++++
 2 files changed, 474 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-mccmon6.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cccdbcb..316c178 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -393,6 +393,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-icore.dtb \
 	imx6q-icore-rqs.dtb \
 	imx6q-marsboard.dtb \
+	imx6q-mccmon6.dtb \
 	imx6q-nitrogen6x.dtb \
 	imx6q-nitrogen6_max.dtb \
 	imx6q-nitrogen6_som2.dtb \
diff --git a/arch/arm/boot/dts/imx6q-mccmon6.dts b/arch/arm/boot/dts/imx6q-mccmon6.dts
new file mode 100644
index 0000000..eedbe73
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-mccmon6.dts
@@ -0,0 +1,473 @@
+/*
+ * Copyright 2016-2017
+ * Lukasz Majewski, DENX Software Engineering, lukma@xxxxxxx
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Liebherr (LWN) monitor6 i.MX6 Quad Board";
+	compatible = "lwn,mccmon6", "fsl,imx6q";
+
+	memory {
+		reg = <0x10000000 0x80000000>;
+	};
+
+	backlight_lvds: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		pwms = <&pwm2 0 5000000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <  0   1   2   3   4   5   6   7   8   9
+				      10  11  12  13  14  15  16  17  18  19
+				      20  21  22  23  24  25  26  27  28  29
+				      30  31  32  33  34  35  36  37  38  39
+				      40  41  42  43  44  45  46  47  48  49
+				      50  51  52  53  54  55  56  57  58  59
+				      60  61  62  63  64  65  66  67  68  69
+				      70  71  72  73  74  75  76  77  78  79
+				      80  81  82  83  84  85  86  87  88  89
+				      90  91  92  93  94  95  96  97  98  99
+				     100 101 102 103 104 105 106 107 108 109
+				     110 111 112 113 114 115 116 117 118 119
+				     120 121 122 123 124 125 126 127 128 129
+				     130 131 132 133 134 135 136 137 138 139
+				     140 141 142 143 144 145 146 147 148 149
+				     150 151 152 153 154 155 156 157 158 159
+				     160 161 162 163 164 165 166 167 168 169
+				     170 171 172 173 174 175 176 177 178 179
+				     180 181 182 183 184 185 186 187 188 189
+				     190 191 192 193 194 195 196 197 198 199
+				     200 201 202 203 204 205 206 207 208 209
+				     210 211 212 213 214 215 216 217 218 219
+				     220 221 222 223 224 225 226 227 228 229
+				     230 231 232 233 234 235 236 237 238 239
+				     240 241 242 243 244 245 246 247 248 249
+				     250 251 252 253 254 255>;
+		default-brightness-level = <50>;
+		enable-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_lvds: regulator-lvds {
+		compatible = "regulator-fixed";
+		regulator-name = "lvds_ppen";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_lvds>;
+		gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	panel-lvds0 {
+		compatible = "innolux,g121x1-l03";
+		backlight = <&backlight_lvds>;
+		power-supply = <&reg_lvds>;
+
+		port {
+			panel_in_lvds0: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+};
+
+&ecspi3 {
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs &pinctrl_ecspi3_flwp>;
+	status = "okay";
+
+	s25sl032p: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <40000000>;
+		reg = <0>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pfuze100: pmic@08 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw1c_reg: sw1c {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&ldb {
+	status = "okay";
+
+	lvds0: lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in_lvds0>;
+			};
+		};
+	};
+};
+
+&pwm2 {
+	#pwm-cells = <3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&weim {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_weim_nor &pinctrl_weim_cs0>;
+	ranges = <0 0 0x08000000 0x08000000>;
+	status = "okay";
+
+	nor@0,0 {
+		compatible = "cfi-flash";
+		reg = <0 0 0x02000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		bank-width = <2>;
+		use-advanced-sector-protection;
+		fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
+				0x0000c000 0x1404a38e 0x00000000>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+
+	pinctrl_backlight: dispgrp {
+		fsl,pins = <
+			/* BLEN_OUT */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02    0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+		>;
+	};
+
+	pinctrl_ecspi3_cs: ecspi3csgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000
+		>;
+	};
+
+	pinctrl_ecspi3_flwp: ecspi3flwpgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x80000000
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b0b0
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+			MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
+			MX6QDL_PAD_ENET_RXD0__GPIO1_IO27        0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL	0x4001b8b1
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__PWM2_OUT	0x1b0b1
+		>;
+	};
+
+	pinctrl_reg_lvds: reqlvdsgrp {
+		fsl,pins = <
+			/* LVDS_PPEN_OUT */
+			MX6QDL_PAD_SD1_DAT2__GPIO1_IO19         0x1b0b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04           0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
+			MX6QDL_PAD_SD3_RST__SD3_RESET		0x17059
+		>;
+	};
+
+	pinctrl_weim_cs0: weimcs0grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_CS0__EIM_CS0_B		0xb0b1
+		>;
+	};
+
+	pinctrl_weim_nor: weimnorgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0b1
+			MX6QDL_PAD_EIM_RW__EIM_RW		0xb0b1
+			MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B	0xb060
+			MX6QDL_PAD_EIM_D16__EIM_DATA16		0x1b0b0
+			MX6QDL_PAD_EIM_D17__EIM_DATA17		0x1b0b0
+			MX6QDL_PAD_EIM_D18__EIM_DATA18		0x1b0b0
+			MX6QDL_PAD_EIM_D19__EIM_DATA19		0x1b0b0
+			MX6QDL_PAD_EIM_D20__EIM_DATA20		0x1b0b0
+			MX6QDL_PAD_EIM_D21__EIM_DATA21		0x1b0b0
+			MX6QDL_PAD_EIM_D22__EIM_DATA22		0x1b0b0
+			MX6QDL_PAD_EIM_D23__EIM_DATA23		0x1b0b0
+			MX6QDL_PAD_EIM_D24__EIM_DATA24		0x1b0b0
+			MX6QDL_PAD_EIM_D25__EIM_DATA25		0x1b0b0
+			MX6QDL_PAD_EIM_D26__EIM_DATA26		0x1b0b0
+			MX6QDL_PAD_EIM_D27__EIM_DATA27		0x1b0b0
+			MX6QDL_PAD_EIM_D28__EIM_DATA28		0x1b0b0
+			MX6QDL_PAD_EIM_D29__EIM_DATA29		0x1b0b0
+			MX6QDL_PAD_EIM_D30__EIM_DATA30		0x1b0b0
+			MX6QDL_PAD_EIM_D31__EIM_DATA31		0x1b0b0
+			MX6QDL_PAD_EIM_A23__EIM_ADDR23		0xb0b1
+			MX6QDL_PAD_EIM_A22__EIM_ADDR22		0xb0b1
+			MX6QDL_PAD_EIM_A21__EIM_ADDR21		0xb0b1
+			MX6QDL_PAD_EIM_A20__EIM_ADDR20		0xb0b1
+			MX6QDL_PAD_EIM_A19__EIM_ADDR19		0xb0b1
+			MX6QDL_PAD_EIM_A18__EIM_ADDR18		0xb0b1
+			MX6QDL_PAD_EIM_A17__EIM_ADDR17		0xb0b1
+			MX6QDL_PAD_EIM_A16__EIM_ADDR16		0xb0b1
+			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0b1
+			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0b1
+			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0b1
+			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0b1
+			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0b1
+			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0b1
+			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0b1
+			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0b1
+			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0b1
+			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0b1
+			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0b1
+			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0b1
+			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0b1
+			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0b1
+			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0b1
+			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0b1
+		>;
+	};
+};
-- 
2.1.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux