On Monday 07 November 2016 05:38 PM, William Wu wrote:
> The rk3399 SoC USB2 PHY is comprised of one Host port and
> one OTG port. And OTG port is for USB2.0 part of USB3.0 OTG
> controller, as a part to construct a fully feature Type-C
> subsystem.
>
> With this patch, we can support OTG port with the following
> functions:
> - Support BC1.2 charger detect, and use extcon notifier to
> send USB charger types to power driver.
> - Support PHY suspend for power management.
> - Support OTG Host only mode.
>
> Signed-off-by: William Wu <wulf@xxxxxxxxxxxxxx>
merged.
Thanks
Kishon
> ---
> Changes in v3:
> - split the clock fix into a separate patch
>
> Changes in v2:
> - remove wakelock
>
> drivers/phy/phy-rockchip-inno-usb2.c | 591 +++++++++++++++++++++++++++++++++--
> 1 file changed, 561 insertions(+), 30 deletions(-)
>
> diff --git a/drivers/phy/phy-rockchip-inno-usb2.c b/drivers/phy/phy-rockchip-inno-usb2.c
> index ac20310..ecfd7d1 100644
> --- a/drivers/phy/phy-rockchip-inno-usb2.c
> +++ b/drivers/phy/phy-rockchip-inno-usb2.c
> @@ -17,6 +17,7 @@
> #include <linux/clk.h>
> #include <linux/clk-provider.h>
> #include <linux/delay.h>
> +#include <linux/extcon.h>
> #include <linux/interrupt.h>
> #include <linux/io.h>
> #include <linux/gpio/consumer.h>
> @@ -30,11 +31,15 @@
> #include <linux/of_platform.h>
> #include <linux/phy/phy.h>
> #include <linux/platform_device.h>
> +#include <linux/power_supply.h>
> #include <linux/regmap.h>
> #include <linux/mfd/syscon.h>
> +#include <linux/usb/of.h>
> +#include <linux/usb/otg.h>
>
> #define BIT_WRITEABLE_SHIFT 16
> -#define SCHEDULE_DELAY (60 * HZ)
> +#define SCHEDULE_DELAY (60 * HZ)
> +#define OTG_SCHEDULE_DELAY (2 * HZ)
>
> enum rockchip_usb2phy_port_id {
> USB2PHY_PORT_OTG,
> @@ -49,6 +54,37 @@ enum rockchip_usb2phy_host_state {
> PHY_STATE_FS_LS_ONLINE = 4,
> };
>
> +/**
> + * Different states involved in USB charger detection.
> + * USB_CHG_STATE_UNDEFINED USB charger is not connected or detection
> + * process is not yet started.
> + * USB_CHG_STATE_WAIT_FOR_DCD Waiting for Data pins contact.
> + * USB_CHG_STATE_DCD_DONE Data pin contact is detected.
> + * USB_CHG_STATE_PRIMARY_DONE Primary detection is completed (Detects
> + * between SDP and DCP/CDP).
> + * USB_CHG_STATE_SECONDARY_DONE Secondary detection is completed (Detects
> + * between DCP and CDP).
> + * USB_CHG_STATE_DETECTED USB charger type is determined.
> + */
> +enum usb_chg_state {
> + USB_CHG_STATE_UNDEFINED = 0,
> + USB_CHG_STATE_WAIT_FOR_DCD,
> + USB_CHG_STATE_DCD_DONE,
> + USB_CHG_STATE_PRIMARY_DONE,
> + USB_CHG_STATE_SECONDARY_DONE,
> + USB_CHG_STATE_DETECTED,
> +};
> +
> +static const unsigned int rockchip_usb2phy_extcon_cable[] = {
> + EXTCON_USB,
> + EXTCON_USB_HOST,
> + EXTCON_CHG_USB_SDP,
> + EXTCON_CHG_USB_CDP,
> + EXTCON_CHG_USB_DCP,
> + EXTCON_CHG_USB_SLOW,
> + EXTCON_NONE,
> +};
> +
> struct usb2phy_reg {
> unsigned int offset;
> unsigned int bitend;
> @@ -58,19 +94,55 @@ struct usb2phy_reg {
> };
>
> /**
> + * struct rockchip_chg_det_reg: usb charger detect registers
> + * @cp_det: charging port detected successfully.
> + * @dcp_det: dedicated charging port detected successfully.
> + * @dp_det: assert data pin connect successfully.
> + * @idm_sink_en: open dm sink curren.
> + * @idp_sink_en: open dp sink current.
> + * @idp_src_en: open dm source current.
> + * @rdm_pdwn_en: open dm pull down resistor.
> + * @vdm_src_en: open dm voltage source.
> + * @vdp_src_en: open dp voltage source.
> + * @opmode: utmi operational mode.
> + */
> +struct rockchip_chg_det_reg {
> + struct usb2phy_reg cp_det;
> + struct usb2phy_reg dcp_det;
> + struct usb2phy_reg dp_det;
> + struct usb2phy_reg idm_sink_en;
> + struct usb2phy_reg idp_sink_en;
> + struct usb2phy_reg idp_src_en;
> + struct usb2phy_reg rdm_pdwn_en;
> + struct usb2phy_reg vdm_src_en;
> + struct usb2phy_reg vdp_src_en;
> + struct usb2phy_reg opmode;
> +};
> +
> +/**
> * struct rockchip_usb2phy_port_cfg: usb-phy port configuration.
> * @phy_sus: phy suspend register.
> + * @bvalid_det_en: vbus valid rise detection enable register.
> + * @bvalid_det_st: vbus valid rise detection status register.
> + * @bvalid_det_clr: vbus valid rise detection clear register.
> * @ls_det_en: linestate detection enable register.
> * @ls_det_st: linestate detection state register.
> * @ls_det_clr: linestate detection clear register.
> + * @utmi_avalid: utmi vbus avalid status register.
> + * @utmi_bvalid: utmi vbus bvalid status register.
> * @utmi_ls: utmi linestate state register.
> * @utmi_hstdet: utmi host disconnect register.
> */
> struct rockchip_usb2phy_port_cfg {
> struct usb2phy_reg phy_sus;
> + struct usb2phy_reg bvalid_det_en;
> + struct usb2phy_reg bvalid_det_st;
> + struct usb2phy_reg bvalid_det_clr;
> struct usb2phy_reg ls_det_en;
> struct usb2phy_reg ls_det_st;
> struct usb2phy_reg ls_det_clr;
> + struct usb2phy_reg utmi_avalid;
> + struct usb2phy_reg utmi_bvalid;
> struct usb2phy_reg utmi_ls;
> struct usb2phy_reg utmi_hstdet;
> };
> @@ -80,31 +152,51 @@ struct rockchip_usb2phy_port_cfg {
> * @reg: the address offset of grf for usb-phy config.
> * @num_ports: specify how many ports that the phy has.
> * @clkout_ctl: keep on/turn off output clk of phy.
> + * @chg_det: charger detection registers.
> */
> struct rockchip_usb2phy_cfg {
> unsigned int reg;
> unsigned int num_ports;
> struct usb2phy_reg clkout_ctl;
> const struct rockchip_usb2phy_port_cfg port_cfgs[USB2PHY_NUM_PORTS];
> + const struct rockchip_chg_det_reg chg_det;
> };
>
> /**
> * struct rockchip_usb2phy_port: usb-phy port data.
> * @port_id: flag for otg port or host port.
> * @suspended: phy suspended flag.
> + * @utmi_avalid: utmi avalid status usage flag.
> + * true - use avalid to get vbus status
> + * flase - use bvalid to get vbus status
> + * @vbus_attached: otg device vbus status.
> + * @bvalid_irq: IRQ number assigned for vbus valid rise detection.
> * @ls_irq: IRQ number assigned for linestate detection.
> * @mutex: for register updating in sm_work.
> - * @sm_work: OTG state machine work.
> + * @chg_work: charge detect work.
> + * @otg_sm_work: OTG state machine work.
> + * @sm_work: HOST state machine work.
> * @phy_cfg: port register configuration, assigned by driver data.
> + * @event_nb: hold event notification callback.
> + * @state: define OTG enumeration states before device reset.
> + * @mode: the dr_mode of the controller.
> */
> struct rockchip_usb2phy_port {
> struct phy *phy;
> unsigned int port_id;
> bool suspended;
> + bool utmi_avalid;
> + bool vbus_attached;
> + int bvalid_irq;
> int ls_irq;
> struct mutex mutex;
> + struct delayed_work chg_work;
> + struct delayed_work otg_sm_work;
> struct delayed_work sm_work;
> const struct rockchip_usb2phy_port_cfg *port_cfg;
> + struct notifier_block event_nb;
> + enum usb_otg_state state;
> + enum usb_dr_mode mode;
> };
>
> /**
> @@ -113,6 +205,11 @@ struct rockchip_usb2phy_port {
> * @clk: clock struct of phy input clk.
> * @clk480m: clock struct of phy output clk.
> * @clk_hw: clock struct of phy output clk management.
> + * @chg_state: states involved in USB charger detection.
> + * @chg_type: USB charger types.
> + * @dcd_retries: The retry count used to track Data contact
> + * detection process.
> + * @edev: extcon device for notification registration
> * @phy_cfg: phy register configuration, assigned by driver data.
> * @ports: phy port instance.
> */
> @@ -122,6 +219,10 @@ struct rockchip_usb2phy {
> struct clk *clk;
> struct clk *clk480m;
> struct clk_hw clk480m_hw;
> + enum usb_chg_state chg_state;
> + enum power_supply_type chg_type;
> + u8 dcd_retries;
> + struct extcon_dev *edev;
> const struct rockchip_usb2phy_cfg *phy_cfg;
> struct rockchip_usb2phy_port ports[USB2PHY_NUM_PORTS];
> };
> @@ -263,33 +364,84 @@ rockchip_usb2phy_clk480m_register(struct rockchip_usb2phy *rphy)
> return ret;
> }
>
> -static int rockchip_usb2phy_init(struct phy *phy)
> +static int rockchip_usb2phy_extcon_register(struct rockchip_usb2phy *rphy)
> {
> - struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
> - struct rockchip_usb2phy *rphy = dev_get_drvdata(phy->dev.parent);
> int ret;
> + struct device_node *node = rphy->dev->of_node;
> + struct extcon_dev *edev;
> +
> + if (of_property_read_bool(node, "extcon")) {
> + edev = extcon_get_edev_by_phandle(rphy->dev, 0);
> + if (IS_ERR(edev)) {
> + if (PTR_ERR(edev) != -EPROBE_DEFER)
> + dev_err(rphy->dev, "Invalid or missing extcon\n");
> + return PTR_ERR(edev);
> + }
> + } else {
> + /* Initialize extcon device */
> + edev = devm_extcon_dev_allocate(rphy->dev,
> + rockchip_usb2phy_extcon_cable);
>
> - if (rport->port_id == USB2PHY_PORT_HOST) {
> - /* clear linestate and enable linestate detect irq */
> - mutex_lock(&rport->mutex);
> + if (IS_ERR(edev))
> + return -ENOMEM;
>
> - ret = property_enable(rphy, &rport->port_cfg->ls_det_clr, true);
> + ret = devm_extcon_dev_register(rphy->dev, edev);
> if (ret) {
> - mutex_unlock(&rport->mutex);
> + dev_err(rphy->dev, "failed to register extcon device\n");
> return ret;
> }
> + }
>
> - ret = property_enable(rphy, &rport->port_cfg->ls_det_en, true);
> - if (ret) {
> - mutex_unlock(&rport->mutex);
> - return ret;
> + rphy->edev = edev;
> +
> + return 0;
> +}
> +
> +static int rockchip_usb2phy_init(struct phy *phy)
> +{
> + struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
> + struct rockchip_usb2phy *rphy = dev_get_drvdata(phy->dev.parent);
> + int ret = 0;
> +
> + mutex_lock(&rport->mutex);
> +
> + if (rport->port_id == USB2PHY_PORT_OTG) {
> + if (rport->mode != USB_DR_MODE_HOST) {
> + /* clear bvalid status and enable bvalid detect irq */
> + ret = property_enable(rphy,
> + &rport->port_cfg->bvalid_det_clr,
> + true);
> + if (ret)
> + goto out;
> +
> + ret = property_enable(rphy,
> + &rport->port_cfg->bvalid_det_en,
> + true);
> + if (ret)
> + goto out;
> +
> + schedule_delayed_work(&rport->otg_sm_work,
> + OTG_SCHEDULE_DELAY);
> + } else {
> + /* If OTG works in host only mode, do nothing. */
> + dev_dbg(&rport->phy->dev, "mode %d\n", rport->mode);
> }
> + } else if (rport->port_id == USB2PHY_PORT_HOST) {
> + /* clear linestate and enable linestate detect irq */
> + ret = property_enable(rphy, &rport->port_cfg->ls_det_clr, true);
> + if (ret)
> + goto out;
> +
> + ret = property_enable(rphy, &rport->port_cfg->ls_det_en, true);
> + if (ret)
> + goto out;
>
> - mutex_unlock(&rport->mutex);
> schedule_delayed_work(&rport->sm_work, SCHEDULE_DELAY);
> }
>
> - return 0;
> +out:
> + mutex_unlock(&rport->mutex);
> + return ret;
> }
>
> static int rockchip_usb2phy_power_on(struct phy *phy)
> @@ -340,7 +492,11 @@ static int rockchip_usb2phy_exit(struct phy *phy)
> {
> struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
>
> - if (rport->port_id == USB2PHY_PORT_HOST)
> + if (rport->port_id == USB2PHY_PORT_OTG &&
> + rport->mode != USB_DR_MODE_HOST) {
> + cancel_delayed_work_sync(&rport->otg_sm_work);
> + cancel_delayed_work_sync(&rport->chg_work);
> + } else if (rport->port_id == USB2PHY_PORT_HOST)
> cancel_delayed_work_sync(&rport->sm_work);
>
> return 0;
> @@ -354,6 +510,249 @@ static const struct phy_ops rockchip_usb2phy_ops = {
> .owner = THIS_MODULE,
> };
>
> +static void rockchip_usb2phy_otg_sm_work(struct work_struct *work)
> +{
> + struct rockchip_usb2phy_port *rport =
> + container_of(work, struct rockchip_usb2phy_port,
> + otg_sm_work.work);
> + struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
> + static unsigned int cable;
> + unsigned long delay;
> + bool vbus_attach, sch_work, notify_charger;
> +
> + if (rport->utmi_avalid)
> + vbus_attach =
> + property_enabled(rphy, &rport->port_cfg->utmi_avalid);
> + else
> + vbus_attach =
> + property_enabled(rphy, &rport->port_cfg->utmi_bvalid);
> +
> + sch_work = false;
> + notify_charger = false;
> + delay = OTG_SCHEDULE_DELAY;
> + dev_dbg(&rport->phy->dev, "%s otg sm work\n",
> + usb_otg_state_string(rport->state));
> +
> + switch (rport->state) {
> + case OTG_STATE_UNDEFINED:
> + rport->state = OTG_STATE_B_IDLE;
> + if (!vbus_attach)
> + rockchip_usb2phy_power_off(rport->phy);
> + /* fall through */
> + case OTG_STATE_B_IDLE:
> + if (extcon_get_cable_state_(rphy->edev, EXTCON_USB_HOST) > 0) {
> + dev_dbg(&rport->phy->dev, "usb otg host connect\n");
> + rport->state = OTG_STATE_A_HOST;
> + rockchip_usb2phy_power_on(rport->phy);
> + return;
> + } else if (vbus_attach) {
> + dev_dbg(&rport->phy->dev, "vbus_attach\n");
> + switch (rphy->chg_state) {
> + case USB_CHG_STATE_UNDEFINED:
> + schedule_delayed_work(&rport->chg_work, 0);
> + return;
> + case USB_CHG_STATE_DETECTED:
> + switch (rphy->chg_type) {
> + case POWER_SUPPLY_TYPE_USB:
> + dev_dbg(&rport->phy->dev,
> + "sdp cable is connecetd\n");
> + rockchip_usb2phy_power_on(rport->phy);
> + rport->state = OTG_STATE_B_PERIPHERAL;
> + notify_charger = true;
> + sch_work = true;
> + cable = EXTCON_CHG_USB_SDP;
> + break;
> + case POWER_SUPPLY_TYPE_USB_DCP:
> + dev_dbg(&rport->phy->dev,
> + "dcp cable is connecetd\n");
> + rockchip_usb2phy_power_off(rport->phy);
> + notify_charger = true;
> + sch_work = true;
> + cable = EXTCON_CHG_USB_DCP;
> + break;
> + case POWER_SUPPLY_TYPE_USB_CDP:
> + dev_dbg(&rport->phy->dev,
> + "cdp cable is connecetd\n");
> + rockchip_usb2phy_power_on(rport->phy);
> + rport->state = OTG_STATE_B_PERIPHERAL;
> + notify_charger = true;
> + sch_work = true;
> + cable = EXTCON_CHG_USB_CDP;
> + break;
> + default:
> + break;
> + }
> + break;
> + default:
> + break;
> + }
> + } else {
> + notify_charger = true;
> + rphy->chg_state = USB_CHG_STATE_UNDEFINED;
> + rphy->chg_type = POWER_SUPPLY_TYPE_UNKNOWN;
> + }
> +
> + if (rport->vbus_attached != vbus_attach) {
> + rport->vbus_attached = vbus_attach;
> +
> + if (notify_charger && rphy->edev)
> + extcon_set_cable_state_(rphy->edev,
> + cable, vbus_attach);
> + }
> + break;
> + case OTG_STATE_B_PERIPHERAL:
> + if (!vbus_attach) {
> + dev_dbg(&rport->phy->dev, "usb disconnect\n");
> + rphy->chg_state = USB_CHG_STATE_UNDEFINED;
> + rphy->chg_type = POWER_SUPPLY_TYPE_UNKNOWN;
> + rport->state = OTG_STATE_B_IDLE;
> + delay = 0;
> + rockchip_usb2phy_power_off(rport->phy);
> + }
> + sch_work = true;
> + break;
> + case OTG_STATE_A_HOST:
> + if (extcon_get_cable_state_(rphy->edev, EXTCON_USB_HOST) == 0) {
> + dev_dbg(&rport->phy->dev, "usb otg host disconnect\n");
> + rport->state = OTG_STATE_B_IDLE;
> + rockchip_usb2phy_power_off(rport->phy);
> + }
> + break;
> + default:
> + break;
> + }
> +
> + if (sch_work)
> + schedule_delayed_work(&rport->otg_sm_work, delay);
> +}
> +
> +static const char *chg_to_string(enum power_supply_type chg_type)
> +{
> + switch (chg_type) {
> + case POWER_SUPPLY_TYPE_USB:
> + return "USB_SDP_CHARGER";
> + case POWER_SUPPLY_TYPE_USB_DCP:
> + return "USB_DCP_CHARGER";
> + case POWER_SUPPLY_TYPE_USB_CDP:
> + return "USB_CDP_CHARGER";
> + default:
> + return "INVALID_CHARGER";
> + }
> +}
> +
> +static void rockchip_chg_enable_dcd(struct rockchip_usb2phy *rphy,
> + bool en)
> +{
> + property_enable(rphy, &rphy->phy_cfg->chg_det.rdm_pdwn_en, en);
> + property_enable(rphy, &rphy->phy_cfg->chg_det.idp_src_en, en);
> +}
> +
> +static void rockchip_chg_enable_primary_det(struct rockchip_usb2phy *rphy,
> + bool en)
> +{
> + property_enable(rphy, &rphy->phy_cfg->chg_det.vdp_src_en, en);
> + property_enable(rphy, &rphy->phy_cfg->chg_det.idm_sink_en, en);
> +}
> +
> +static void rockchip_chg_enable_secondary_det(struct rockchip_usb2phy *rphy,
> + bool en)
> +{
> + property_enable(rphy, &rphy->phy_cfg->chg_det.vdm_src_en, en);
> + property_enable(rphy, &rphy->phy_cfg->chg_det.idp_sink_en, en);
> +}
> +
> +#define CHG_DCD_POLL_TIME (100 * HZ / 1000)
> +#define CHG_DCD_MAX_RETRIES 6
> +#define CHG_PRIMARY_DET_TIME (40 * HZ / 1000)
> +#define CHG_SECONDARY_DET_TIME (40 * HZ / 1000)
> +static void rockchip_chg_detect_work(struct work_struct *work)
> +{
> + struct rockchip_usb2phy_port *rport =
> + container_of(work, struct rockchip_usb2phy_port, chg_work.work);
> + struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
> + bool is_dcd, tmout, vout;
> + unsigned long delay;
> +
> + dev_dbg(&rport->phy->dev, "chg detection work state = %d\n",
> + rphy->chg_state);
> + switch (rphy->chg_state) {
> + case USB_CHG_STATE_UNDEFINED:
> + if (!rport->suspended)
> + rockchip_usb2phy_power_off(rport->phy);
> + /* put the controller in non-driving mode */
> + property_enable(rphy, &rphy->phy_cfg->chg_det.opmode, false);
> + /* Start DCD processing stage 1 */
> + rockchip_chg_enable_dcd(rphy, true);
> + rphy->chg_state = USB_CHG_STATE_WAIT_FOR_DCD;
> + rphy->dcd_retries = 0;
> + delay = CHG_DCD_POLL_TIME;
> + break;
> + case USB_CHG_STATE_WAIT_FOR_DCD:
> + /* get data contact detection status */
> + is_dcd = property_enabled(rphy, &rphy->phy_cfg->chg_det.dp_det);
> + tmout = ++rphy->dcd_retries == CHG_DCD_MAX_RETRIES;
> + /* stage 2 */
> + if (is_dcd || tmout) {
> + /* stage 4 */
> + /* Turn off DCD circuitry */
> + rockchip_chg_enable_dcd(rphy, false);
> + /* Voltage Source on DP, Probe on DM */
> + rockchip_chg_enable_primary_det(rphy, true);
> + delay = CHG_PRIMARY_DET_TIME;
> + rphy->chg_state = USB_CHG_STATE_DCD_DONE;
> + } else {
> + /* stage 3 */
> + delay = CHG_DCD_POLL_TIME;
> + }
> + break;
> + case USB_CHG_STATE_DCD_DONE:
> + vout = property_enabled(rphy, &rphy->phy_cfg->chg_det.cp_det);
> + rockchip_chg_enable_primary_det(rphy, false);
> + if (vout) {
> + /* Voltage Source on DM, Probe on DP */
> + rockchip_chg_enable_secondary_det(rphy, true);
> + delay = CHG_SECONDARY_DET_TIME;
> + rphy->chg_state = USB_CHG_STATE_PRIMARY_DONE;
> + } else {
> + if (tmout) {
> + /* floating charger found */
> + rphy->chg_type = POWER_SUPPLY_TYPE_USB_DCP;
> + rphy->chg_state = USB_CHG_STATE_DETECTED;
> + delay = 0;
> + } else {
> + rphy->chg_type = POWER_SUPPLY_TYPE_USB;
> + rphy->chg_state = USB_CHG_STATE_DETECTED;
> + delay = 0;
> + }
> + }
> + break;
> + case USB_CHG_STATE_PRIMARY_DONE:
> + vout = property_enabled(rphy, &rphy->phy_cfg->chg_det.dcp_det);
> + /* Turn off voltage source */
> + rockchip_chg_enable_secondary_det(rphy, false);
> + if (vout)
> + rphy->chg_type = POWER_SUPPLY_TYPE_USB_DCP;
> + else
> + rphy->chg_type = POWER_SUPPLY_TYPE_USB_CDP;
> + /* fall through */
> + case USB_CHG_STATE_SECONDARY_DONE:
> + rphy->chg_state = USB_CHG_STATE_DETECTED;
> + delay = 0;
> + /* fall through */
> + case USB_CHG_STATE_DETECTED:
> + /* put the controller in normal mode */
> + property_enable(rphy, &rphy->phy_cfg->chg_det.opmode, true);
> + rockchip_usb2phy_otg_sm_work(&rport->otg_sm_work.work);
> + dev_info(&rport->phy->dev, "charger = %s\n",
> + chg_to_string(rphy->chg_type));
> + return;
> + default:
> + return;
> + }
> +
> + schedule_delayed_work(&rport->chg_work, delay);
> +}
> +
> /*
> * The function manage host-phy port state and suspend/resume phy port
> * to save power.
> @@ -485,6 +884,26 @@ static irqreturn_t rockchip_usb2phy_linestate_irq(int irq, void *data)
> return IRQ_HANDLED;
> }
>
> +static irqreturn_t rockchip_usb2phy_bvalid_irq(int irq, void *data)
> +{
> + struct rockchip_usb2phy_port *rport = data;
> + struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
> +
> + if (!property_enabled(rphy, &rport->port_cfg->bvalid_det_st))
> + return IRQ_NONE;
> +
> + mutex_lock(&rport->mutex);
> +
> + /* clear bvalid detect irq pending status */
> + property_enable(rphy, &rport->port_cfg->bvalid_det_clr, true);
> +
> + mutex_unlock(&rport->mutex);
> +
> + rockchip_usb2phy_otg_sm_work(&rport->otg_sm_work.work);
> +
> + return IRQ_HANDLED;
> +}
> +
> static int rockchip_usb2phy_host_port_init(struct rockchip_usb2phy *rphy,
> struct rockchip_usb2phy_port *rport,
> struct device_node *child_np)
> @@ -509,13 +928,86 @@ static int rockchip_usb2phy_host_port_init(struct rockchip_usb2phy *rphy,
> IRQF_ONESHOT,
> "rockchip_usb2phy", rport);
> if (ret) {
> - dev_err(rphy->dev, "failed to request irq handle\n");
> + dev_err(rphy->dev, "failed to request linestate irq handle\n");
> return ret;
> }
>
> return 0;
> }
>
> +static int rockchip_otg_event(struct notifier_block *nb,
> + unsigned long event, void *ptr)
> +{
> + struct rockchip_usb2phy_port *rport =
> + container_of(nb, struct rockchip_usb2phy_port, event_nb);
> +
> + schedule_delayed_work(&rport->otg_sm_work, OTG_SCHEDULE_DELAY);
> +
> + return NOTIFY_DONE;
> +}
> +
> +static int rockchip_usb2phy_otg_port_init(struct rockchip_usb2phy *rphy,
> + struct rockchip_usb2phy_port *rport,
> + struct device_node *child_np)
> +{
> + int ret;
> +
> + rport->port_id = USB2PHY_PORT_OTG;
> + rport->port_cfg = &rphy->phy_cfg->port_cfgs[USB2PHY_PORT_OTG];
> + rport->state = OTG_STATE_UNDEFINED;
> +
> + /*
> + * set suspended flag to true, but actually don't
> + * put phy in suspend mode, it aims to enable usb
> + * phy and clock in power_on() called by usb controller
> + * driver during probe.
> + */
> + rport->suspended = true;
> + rport->vbus_attached = false;
> +
> + mutex_init(&rport->mutex);
> +
> + rport->mode = of_usb_get_dr_mode_by_phy(child_np, -1);
> + if (rport->mode == USB_DR_MODE_HOST) {
> + ret = 0;
> + goto out;
> + }
> +
> + INIT_DELAYED_WORK(&rport->chg_work, rockchip_chg_detect_work);
> + INIT_DELAYED_WORK(&rport->otg_sm_work, rockchip_usb2phy_otg_sm_work);
> +
> + rport->utmi_avalid =
> + of_property_read_bool(child_np, "rockchip,utmi-avalid");
> +
> + rport->bvalid_irq = of_irq_get_byname(child_np, "otg-bvalid");
> + if (rport->bvalid_irq < 0) {
> + dev_err(rphy->dev, "no vbus valid irq provided\n");
> + ret = rport->bvalid_irq;
> + goto out;
> + }
> +
> + ret = devm_request_threaded_irq(rphy->dev, rport->bvalid_irq, NULL,
> + rockchip_usb2phy_bvalid_irq,
> + IRQF_ONESHOT,
> + "rockchip_usb2phy_bvalid", rport);
> + if (ret) {
> + dev_err(rphy->dev, "failed to request otg-bvalid irq handle\n");
> + goto out;
> + }
> +
> + if (!IS_ERR(rphy->edev)) {
> + rport->event_nb.notifier_call = rockchip_otg_event;
> +
> + ret = extcon_register_notifier(rphy->edev, EXTCON_USB_HOST,
> + &rport->event_nb);
> + if (ret)
> + dev_err(rphy->dev, "register USB HOST notifier failed\n");
> + }
> +
> +out:
> + return ret;
> +}
> +
> static int rockchip_usb2phy_probe(struct platform_device *pdev)
> {
> struct device *dev = &pdev->dev;
> @@ -553,8 +1045,14 @@ static int rockchip_usb2phy_probe(struct platform_device *pdev)
>
> rphy->dev = dev;
> phy_cfgs = match->data;
> + rphy->chg_state = USB_CHG_STATE_UNDEFINED;
> + rphy->chg_type = POWER_SUPPLY_TYPE_UNKNOWN;
> platform_set_drvdata(pdev, rphy);
>
> + ret = rockchip_usb2phy_extcon_register(rphy);
> + if (ret)
> + return ret;
> +
> /* find out a proper config which can be matched with dt. */
> index = 0;
> while (phy_cfgs[index].reg) {
> @@ -591,13 +1089,9 @@ static int rockchip_usb2phy_probe(struct platform_device *pdev)
> struct rockchip_usb2phy_port *rport = &rphy->ports[index];
> struct phy *phy;
>
> - /*
> - * This driver aim to support both otg-port and host-port,
> - * but unfortunately, the otg part is not ready in current,
> - * so this comments and below codes are interim, which should
> - * be changed after otg-port is supplied soon.
> - */
> - if (of_node_cmp(child_np->name, "host-port"))
> + /* This driver aims to support both otg-port and host-port */
> + if (of_node_cmp(child_np->name, "host-port") &&
> + of_node_cmp(child_np->name, "otg-port"))
> goto next_child;
>
> phy = devm_phy_create(dev, child_np, &rockchip_usb2phy_ops);
> @@ -610,9 +1104,18 @@ static int rockchip_usb2phy_probe(struct platform_device *pdev)
> rport->phy = phy;
> phy_set_drvdata(rport->phy, rport);
>
> - ret = rockchip_usb2phy_host_port_init(rphy, rport, child_np);
> - if (ret)
> - goto put_child;
> + /* initialize otg/host port separately */
> + if (!of_node_cmp(child_np->name, "host-port")) {
> + ret = rockchip_usb2phy_host_port_init(rphy, rport,
> + child_np);
> + if (ret)
> + goto put_child;
> + } else {
> + ret = rockchip_usb2phy_otg_port_init(rphy, rport,
> + child_np);
> + if (ret)
> + goto put_child;
> + }
>
> next_child:
> /* to prevent out of boundary */
> @@ -654,10 +1157,18 @@ static const struct rockchip_usb2phy_cfg rk3366_phy_cfgs[] = {
>
> static const struct rockchip_usb2phy_cfg rk3399_phy_cfgs[] = {
> {
> - .reg = 0xe450,
> + .reg = 0xe450,
> .num_ports = 2,
> .clkout_ctl = { 0xe450, 4, 4, 1, 0 },
> .port_cfgs = {
> + [USB2PHY_PORT_OTG] = {
> + .phy_sus = { 0xe454, 1, 0, 2, 1 },
> + .bvalid_det_en = { 0xe3c0, 3, 3, 0, 1 },
> + .bvalid_det_st = { 0xe3e0, 3, 3, 0, 1 },
> + .bvalid_det_clr = { 0xe3d0, 3, 3, 0, 1 },
> + .utmi_avalid = { 0xe2ac, 7, 7, 0, 1 },
> + .utmi_bvalid = { 0xe2ac, 12, 12, 0, 1 },
> + },
> [USB2PHY_PORT_HOST] = {
> .phy_sus = { 0xe458, 1, 0, 0x2, 0x1 },
> .ls_det_en = { 0xe3c0, 6, 6, 0, 1 },
> @@ -667,12 +1178,32 @@ static const struct rockchip_usb2phy_cfg rk3399_phy_cfgs[] = {
> .utmi_hstdet = { 0xe2ac, 23, 23, 0, 1 }
> }
> },
> + .chg_det = {
> + .opmode = { 0xe454, 3, 0, 5, 1 },
> + .cp_det = { 0xe2ac, 2, 2, 0, 1 },
> + .dcp_det = { 0xe2ac, 1, 1, 0, 1 },
> + .dp_det = { 0xe2ac, 0, 0, 0, 1 },
> + .idm_sink_en = { 0xe450, 8, 8, 0, 1 },
> + .idp_sink_en = { 0xe450, 7, 7, 0, 1 },
> + .idp_src_en = { 0xe450, 9, 9, 0, 1 },
> + .rdm_pdwn_en = { 0xe450, 10, 10, 0, 1 },
> + .vdm_src_en = { 0xe450, 12, 12, 0, 1 },
> + .vdp_src_en = { 0xe450, 11, 11, 0, 1 },
> + },
> },
> {
> - .reg = 0xe460,
> + .reg = 0xe460,
> .num_ports = 2,
> .clkout_ctl = { 0xe460, 4, 4, 1, 0 },
> .port_cfgs = {
> + [USB2PHY_PORT_OTG] = {
> + .phy_sus = { 0xe464, 1, 0, 2, 1 },
> + .bvalid_det_en = { 0xe3c0, 8, 8, 0, 1 },
> + .bvalid_det_st = { 0xe3e0, 8, 8, 0, 1 },
> + .bvalid_det_clr = { 0xe3d0, 8, 8, 0, 1 },
> + .utmi_avalid = { 0xe2ac, 10, 10, 0, 1 },
> + .utmi_bvalid = { 0xe2ac, 16, 16, 0, 1 },
> + },
> [USB2PHY_PORT_HOST] = {
> .phy_sus = { 0xe468, 1, 0, 0x2, 0x1 },
> .ls_det_en = { 0xe3c0, 11, 11, 0, 1 },
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
