This patch adds the device tree support for FSL LS2088A SoC based on
ARMv8 architecture.
Following levels of DTSI/DTS files have been created for the LS2088A
SoC family:
- fsl-ls2088a.dtsi:
DTS-Include file for FSL LS2088A SoC.
- fsl-ls2088a-qds.dts:
DTS file for FSL LS2088A QDS board.
- fsl-ls2088a-rdb.dts:
DTS file for FSL LS2088A RDB board.
Signed-off-by: Priyanka Jain <priyanka.jain@xxxxxxx>
Signed-off-by: Ashish Kumar <ashish.kumar@xxxxxxx>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@xxxxxxx>
---
arch/arm64/boot/dts/freescale/Makefile | 2 +
arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts | 211 +++++++
arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts | 166 +++++
arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi | 703 ++++++++++++++++++++++
4 files changed, 1082 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 6602718..fa3d66e 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -5,6 +5,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts
new file mode 100644
index 0000000..2b8d9f3
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts
@@ -0,0 +1,211 @@
+/*
+ * Device Tree file for Freescale LS2088A QDS Board.
+ *
+ * Copyright (C) 2016, Freescale Semiconductor
+ *
+ * Abhimanyu Saini <abhimanyu.saini@xxxxxxx>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+/include/ "fsl-ls2088a.dtsi"
+
+/ {
+ model = "Freescale Layerscape 2088A QDS Board";
+ compatible = "fsl,ls2088a-qds", "fsl,ls2088a";
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ };
+
+};
+
+&esdhc {
+ status = "okay";
+};
+
+&ifc {
+ status = "okay";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x5 0x80000000 0x08000000
+ 0x2 0x0 0x5 0x30000000 0x00010000
+ 0x3 0x0 0x5 0x20000000 0x00010000>;
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand@2,0 {
+ compatible = "fsl,ifc-nand";
+ reg = <0x2 0x0 0x10000>;
+ };
+
+ cpld@3,0 {
+ reg = <0x3 0x0 0x10000>;
+ compatible = "fsl,ls2088aqds-fpga", "fsl,fpga-qixis";
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ pca9547@77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x00>;
+ rtc@68 {
+ compatible = "dallas,ds3232";
+ reg = <0x68>;
+ };
+ };
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x02>;
+
+ ina220@40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <500>;
+ };
+
+ ina220@41 {
+ compatible = "ti,ina220";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ adt7481@4c {
+ compatible = "adi,adt7461";
+ reg = <0x4c>;
+ };
+ };
+ };
+};
+
+&i2c1 {
+ status = "disabled";
+};
+
+&i2c2 {
+ status = "disabled";
+};
+
+&i2c3 {
+ status = "disabled";
+};
+
+&dspi {
+ status = "okay";
+ dflash0: n25q128a {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p80";
+ spi-max-frequency = <3000000>;
+ reg = <0>;
+ };
+ dflash1: sst25wf040b {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p80";
+ spi-max-frequency = <3000000>;
+ reg = <1>;
+ };
+ dflash2: en25s64 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p80";
+ spi-max-frequency = <3000000>;
+ reg = <2>;
+ };
+};
+
+&qspi {
+ status = "okay";
+ flash0: s25fl256s1@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p80";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+ flash2: s25fl256s1@2 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p80";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+};
+
+&sata0 {
+ status = "okay";
+};
+
+&sata1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
new file mode 100644
index 0000000..6d403bc
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
@@ -0,0 +1,166 @@
+/*
+ * Device Tree file for Freescale LS2088A RDB Board.
+ *
+ * Copyright (C) 2016, Freescale Semiconductor
+ *
+ * Abhimanyu Saini <abhimanyu.saini@xxxxxxx>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+/include/ "fsl-ls2088a.dtsi"
+
+/ {
+ model = "Freescale Layerscape 2088A RDB Board";
+ compatible = "fsl,ls2088a-rdb", "fsl,ls2088a";
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ };
+};
+
+&esdhc {
+ status = "okay";
+};
+
+&ifc {
+ status = "okay";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x5 0x80000000 0x08000000
+ 0x2 0x0 0x5 0x30000000 0x00010000
+ 0x3 0x0 0x5 0x20000000 0x00010000>;
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand@2,0 {
+ compatible = "fsl,ifc-nand";
+ reg = <0x2 0x0 0x10000>;
+ };
+
+ cpld@3,0 {
+ reg = <0x3 0x0 0x10000>;
+ compatible = "fsl,ls2088aqds-fpga", "fsl,fpga-qixis";
+ };
+
+};
+
+&i2c0 {
+ status = "okay";
+ pca9547@75 {
+ compatible = "nxp,pca9547";
+ reg = <0x75>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x01>;
+ rtc@68 {
+ compatible = "dallas,ds3232";
+ reg = <0x68>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ adt7481@4c {
+ compatible = "adi,adt7461";
+ reg = <0x4c>;
+ };
+ };
+ };
+};
+
+&i2c1 {
+ status = "disabled";
+};
+
+&i2c2 {
+ status = "disabled";
+};
+
+&i2c3 {
+ status = "disabled";
+};
+
+&dspi {
+ status = "okay";
+ dflash0: n25q512a {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p80";
+ spi-max-frequency = <3000000>;
+ reg = <0>;
+ };
+};
+
+&qspi {
+ status = "disabled";
+};
+
+&sata0 {
+ status = "okay";
+};
+
+&sata1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi
new file mode 100644
index 0000000..687ab5a
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi
@@ -0,0 +1,703 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-2088A family SoC.
+ *
+ * Copyright (C) 2016, Freescale Semiconductor
+ *
+ * Abhimanyu Saini <abhimanyu.saini@xxxxxxx>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/ {
+ compatible = "fsl,ls2088a";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x0>;
+ clocks = <&clockgen 1 0>;
+ next-level-cache = <&cluster0_l2>;
+ };
+
+ cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x1>;
+ clocks = <&clockgen 1 0>;
+ next-level-cache = <&cluster0_l2>;
+ };
+
+ cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x100>;
+ clocks = <&clockgen 1 1>;
+ next-level-cache = <&cluster1_l2>;
+ };
+
+ cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x101>;
+ clocks = <&clockgen 1 1>;
+ next-level-cache = <&cluster1_l2>;
+ };
+
+ cpu@200 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x200>;
+ clocks = <&clockgen 1 2>;
+ next-level-cache = <&cluster2_l2>;
+ };
+
+ cpu@201 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x201>;
+ clocks = <&clockgen 1 2>;
+ next-level-cache = <&cluster2_l2>;
+ };
+
+ cpu@300 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x300>;
+ clocks = <&clockgen 1 3>;
+ next-level-cache = <&cluster3_l2>;
+ };
+
+ cpu@301 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x301>;
+ clocks = <&clockgen 1 3>;
+ next-level-cache = <&cluster3_l2>;
+ };
+
+ cluster0_l2: l2-cache0 {
+ compatible = "cache";
+ };
+
+ cluster1_l2: l2-cache1 {
+ compatible = "cache";
+ };
+
+ cluster2_l2: l2-cache2 {
+ compatible = "cache";
+ };
+
+ cluster3_l2: l2-cache3 {
+ compatible = "cache";
+ };
+ };
+
+ sysclk: sysclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-output-names = "sysclk";
+ };
+
+ gic: interrupt-controller@6000000 {
+ compatible = "arm,gic-v3";
+ reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */
+ <0x0 0x06100000 0 0x100000>, /* GICR (RD_base + SGI_base) */
+ <0x0 0x0c0c0000 0 0x2000>, /* GICC */
+ <0x0 0x0c0d0000 0 0x1000>, /* GICH */
+ <0x0 0x0c0e0000 0 0x20000>; /* GICV */
+ #interrupt-cells = <3>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ interrupt-controller;
+ interrupts = <1 9 0x4>;
+
+ its: gic-its@6020000 {
+ compatible = "arm,gic-v3-its";
+ msi-controller;
+ reg = <0x0 0x6020000 0 0x20000>;
+ };
+ };
+
+ reboot {
+ compatible ="syscon-reboot";
+ regmap = <&rstcr>;
+ offset = <0x0>;
+ mask = <0x2>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <1 13 0x8>, /* Physical Secure PPI, active-low */
+ <1 14 0x8>, /* Physical Non-Secure PPI, active-low */
+ <1 11 0x8>, /* Virtual PPI, active-low */
+ <1 10 0x8>; /* Hypervisor PPI, active-low */
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <1 7 0x8>; /* PMU PPI, Level low type */
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ rstcr: syscon@1e60000 {
+ compatible = "fsl,ls2088a-rstcr", "fsl,ls2080a-rstcr",
+ "syscon";
+ reg = <0x0 0x1e60000 0x0 0x4>;
+ };
+
+ clockgen: clocking@1300000 {
+ compatible = "fsl,ls2088a-clockgen";
+ reg = <0 0x1300000 0 0xa0000>;
+ #clock-cells = <2>;
+ clocks = <&sysclk>;
+ };
+
+ serial0: serial@21c0500 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x0 0x21c0500 0x0 0x100>;
+ clocks = <&clockgen 4 3>;
+ interrupts = <0 32 0x4>; /* Level high type */
+ };
+
+ serial1: serial@21c0600 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x0 0x21c0600 0x0 0x100>;
+ clocks = <&clockgen 4 3>;
+ interrupts = <0 32 0x4>; /* Level high type */
+ };
+
+ cluster1_core0_watchdog: wdt@c000000 {
+ compatible = "arm,sp805-wdt", "arm,primecell";
+ reg = <0x0 0xc000000 0x0 0x1000>;
+ clocks = <&clockgen 4 3>, <&clockgen 4 3>;
+ clock-names = "apb_pclk", "wdog_clk";
+ };
+
+ cluster1_core1_watchdog: wdt@c010000 {
+ compatible = "arm,sp805-wdt", "arm,primecell";
+ reg = <0x0 0xc010000 0x0 0x1000>;
+ clocks = <&clockgen 4 3>, <&clockgen 4 3>;
+ clock-names = "apb_pclk", "wdog_clk";
+ };
+
+ cluster2_core0_watchdog: wdt@c100000 {
+ compatible = "arm,sp805-wdt", "arm,primecell";
+ reg = <0x0 0xc100000 0x0 0x1000>;
+ clocks = <&clockgen 4 3>, <&clockgen 4 3>;
+ clock-names = "apb_pclk", "wdog_clk";
+ };
+
+ cluster2_core1_watchdog: wdt@c110000 {
+ compatible = "arm,sp805-wdt", "arm,primecell";
+ reg = <0x0 0xc110000 0x0 0x1000>;
+ clocks = <&clockgen 4 3>, <&clockgen 4 3>;
+ clock-names = "apb_pclk", "wdog_clk";
+ };
+
+ cluster3_core0_watchdog: wdt@c200000 {
+ compatible = "arm,sp805-wdt", "arm,primecell";
+ reg = <0x0 0xc200000 0x0 0x1000>;
+ clocks = <&clockgen 4 3>, <&clockgen 4 3>;
+ clock-names = "apb_pclk", "wdog_clk";
+ };
+
+ cluster3_core1_watchdog: wdt@c210000 {
+ compatible = "arm,sp805-wdt", "arm,primecell";
+ reg = <0x0 0xc210000 0x0 0x1000>;
+ clocks = <&clockgen 4 3>, <&clockgen 4 3>;
+ clock-names = "apb_pclk", "wdog_clk";
+ };
+
+ cluster4_core0_watchdog: wdt@c300000 {
+ compatible = "arm,sp805-wdt", "arm,primecell";
+ reg = <0x0 0xc300000 0x0 0x1000>;
+ clocks = <&clockgen 4 3>, <&clockgen 4 3>;
+ clock-names = "apb_pclk", "wdog_clk";
+ };
+
+ cluster4_core1_watchdog: wdt@c310000 {
+ compatible = "arm,sp805-wdt", "arm,primecell";
+ reg = <0x0 0xc310000 0x0 0x1000>;
+ clocks = <&clockgen 4 3>, <&clockgen 4 3>;
+ clock-names = "apb_pclk", "wdog_clk";
+ };
+
+ fsl_mc: fsl-mc@80c000000 {
+ compatible = "fsl,qoriq-mc";
+ reg = <0x00000008 0x0c000000 0 0x40>, /* MC portal base */
+ <0x00000000 0x08340000 0 0x40000>; /* MC control reg */
+ msi-parent = <&its>;
+ #address-cells = <3>;
+ #size-cells = <1>;
+
+ /*
+ * Region type 0x0 - MC portals
+ * Region type 0x1 - QBMAN portals
+ */
+ ranges = <0x0 0x0 0x0 0x8 0x0c000000 0x4000000
+ 0x1 0x0 0x0 0x8 0x18000000 0x8000000>;
+
+ /*
+ * Define the maximum number of MACs present on the SoC.
+ */
+ dpmacs {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dpmac1: dpmac@1 {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0x1>;
+ };
+
+ dpmac2: dpmac@2 {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0x2>;
+ };
+
+ dpmac3: dpmac@3 {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0x3>;
+ };
+
+ dpmac4: dpmac@4 {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0x4>;
+ };
+
+ dpmac5: dpmac@5 {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0x5>;
+ };
+
+ dpmac6: dpmac@6 {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0x6>;
+ };
+
+ dpmac7: dpmac@7 {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0x7>;
+ };
+
+ dpmac8: dpmac@8 {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0x8>;
+ };
+
+ dpmac9: dpmac@9 {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0x9>;
+ };
+
+ dpmac10: dpmac@a {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0xa>;
+ };
+
+ dpmac11: dpmac@b {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0xb>;
+ };
+
+ dpmac12: dpmac@c {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0xc>;
+ };
+
+ dpmac13: dpmac@d {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0xd>;
+ };
+
+ dpmac14: dpmac@e {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0xe>;
+ };
+
+ dpmac15: dpmac@f {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0xf>;
+ };
+
+ dpmac16: dpmac@10 {
+ compatible = "fsl,qoriq-mc-dpmac";
+ reg = <0x10>;
+ };
+ };
+ };
+
+ smmu: iommu@5000000 {
+ compatible = "arm,mmu-500";
+ reg = <0 0x5000000 0 0x800000>;
+ #global-interrupts = <12>;
+ interrupts = <0 13 4>, /* global secure fault */
+ <0 14 4>, /* combined secure interrupt */
+ <0 15 4>, /* global non-secure fault */
+ <0 16 4>, /* combined non-secure interrupt */
+ /* performance counter interrupts 0-7 */
+ <0 211 4>, <0 212 4>,
+ <0 213 4>, <0 214 4>,
+ <0 215 4>, <0 216 4>,
+ <0 217 4>, <0 218 4>,
+ /* per context interrupt, 64 interrupts */
+ <0 146 4>, <0 147 4>,
+ <0 148 4>, <0 149 4>,
+ <0 150 4>, <0 151 4>,
+ <0 152 4>, <0 153 4>,
+ <0 154 4>, <0 155 4>,
+ <0 156 4>, <0 157 4>,
+ <0 158 4>, <0 159 4>,
+ <0 160 4>, <0 161 4>,
+ <0 162 4>, <0 163 4>,
+ <0 164 4>, <0 165 4>,
+ <0 166 4>, <0 167 4>,
+ <0 168 4>, <0 169 4>,
+ <0 170 4>, <0 171 4>,
+ <0 172 4>, <0 173 4>,
+ <0 174 4>, <0 175 4>,
+ <0 176 4>, <0 177 4>,
+ <0 178 4>, <0 179 4>,
+ <0 180 4>, <0 181 4>,
+ <0 182 4>, <0 183 4>,
+ <0 184 4>, <0 185 4>,
+ <0 186 4>, <0 187 4>,
+ <0 188 4>, <0 189 4>,
+ <0 190 4>, <0 191 4>,
+ <0 192 4>, <0 193 4>,
+ <0 194 4>, <0 195 4>,
+ <0 196 4>, <0 197 4>,
+ <0 198 4>, <0 199 4>,
+ <0 200 4>, <0 201 4>,
+ <0 202 4>, <0 203 4>,
+ <0 204 4>, <0 205 4>,
+ <0 206 4>, <0 207 4>,
+ <0 208 4>, <0 209 4>;
+ mmu-masters = <&fsl_mc 0x300 0>;
+ };
+
+ dspi: dspi@2100000 {
+ status = "disabled";
+ compatible = "fsl,ls2088a-dspi", "fsl,ls2085a-dspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2100000 0x0 0x10000>;
+ interrupts = <0 26 0x4>; /* Level high type */
+ clocks = <&clockgen 4 3>;
+ clock-names = "dspi";
+ spi-num-chipselects = <5>;
+ bus-num = <0>;
+ };
+
+ esdhc: esdhc@2140000 {
+ status = "disabled";
+ compatible = "fsl,ls2088a-esdhc", "fsl,esdhc";
+ reg = <0x0 0x2140000 0x0 0x10000>;
+ interrupts = <0 28 0x4>; /* Level high type */
+ clock-frequency = <0>; /* Updated by bootloader */
+ voltage-ranges = <1800 1800 3300 3300>;
+ sdhci,auto-cmd12;
+ little-endian;
+ bus-width = <4>;
+ };
+
+ gpio0: gpio@2300000 {
+ compatible = "fsl,ls2088a-gpio", "fsl,qoriq-gpio";
+ reg = <0x0 0x2300000 0x0 0x10000>;
+ interrupts = <0 36 0x4>; /* Level high type */
+ gpio-controller;
+ little-endian;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio@2310000 {
+ compatible = "fsl,ls2088a-gpio", "fsl,qoriq-gpio";
+ reg = <0x0 0x2310000 0x0 0x10000>;
+ interrupts = <0 36 0x4>; /* Level high type */
+ gpio-controller;
+ little-endian;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@2320000 {
+ compatible = "fsl,ls2088a-gpio", "fsl,qoriq-gpio";
+ reg = <0x0 0x2320000 0x0 0x10000>;
+ interrupts = <0 37 0x4>; /* Level high type */
+ gpio-controller;
+ little-endian;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@2330000 {
+ compatible = "fsl,ls2088a-gpio", "fsl,qoriq-gpio";
+ reg = <0x0 0x2330000 0x0 0x10000>;
+ interrupts = <0 37 0x4>; /* Level high type */
+ gpio-controller;
+ little-endian;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ i2c0: i2c@2000000 {
+ status = "disabled";
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2000000 0x0 0x10000>;
+ interrupts = <0 34 0x4>; /* Level high type */
+ clock-names = "i2c";
+ clocks = <&clockgen 4 3>;
+ };
+
+ i2c1: i2c@2010000 {
+ status = "disabled";
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2010000 0x0 0x10000>;
+ interrupts = <0 34 0x4>; /* Level high type */
+ clock-names = "i2c";
+ clocks = <&clockgen 4 3>;
+ };
+
+ i2c2: i2c@2020000 {
+ status = "disabled";
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2020000 0x0 0x10000>;
+ interrupts = <0 35 0x4>; /* Level high type */
+ clock-names = "i2c";
+ clocks = <&clockgen 4 3>;
+ };
+
+ i2c3: i2c@2030000 {
+ status = "disabled";
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2030000 0x0 0x10000>;
+ interrupts = <0 35 0x4>; /* Level high type */
+ clock-names = "i2c";
+ clocks = <&clockgen 4 3>;
+ };
+
+ ifc: ifc@2240000 {
+ compatible = "fsl,ifc", "simple-bus";
+ reg = <0x0 0x2240000 0x0 0x20000>;
+ interrupts = <0 21 0x4>; /* Level high type */
+ little-endian;
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ ranges = <0 0 0x5 0x80000000 0x08000000
+ 2 0 0x5 0x30000000 0x00010000
+ 3 0 0x5 0x20000000 0x00010000>;
+ };
+
+ qspi: quadspi@20c0000 {
+ status = "disabled";
+ compatible = "fsl,ls2088a-qspi", "fsl,ls1021a-qspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x20c0000 0x0 0x10000>,
+ <0x0 0x20000000 0x0 0x10000000>;
+ reg-names = "QuadSPI", "QuadSPI-memory";
+ interrupts = <0 25 0x4>; /* Level high type */
+ clocks = <&clockgen 4 3>, <&clockgen 4 3>;
+ clock-names = "qspi_en", "qspi";
+ };
+
+ pcie1: pcie@3400000 {
+ compatible = "fsl,ls2088a-pcie", "fsl,ls2080a-pcie",
+ "snps,dw-pcie";
+ reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */
+ 0x20 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
+ interrupts = <0 108 0x4>; /* Level high type */
+ interrupt-names = "intr";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <4>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x20 0x00010000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x20 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ msi-parent = <&its>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 0 0 109 4>,
+ <0000 0 0 2 &gic 0 0 0 110 4>,
+ <0000 0 0 3 &gic 0 0 0 111 4>,
+ <0000 0 0 4 &gic 0 0 0 112 4>;
+ };
+
+ pcie2: pcie@3500000 {
+ compatible = "fsl,ls2088a-pcie", "fsl,ls2080a-pcie",
+ "snps,dw-pcie";
+ reg = <0x00 0x03500000 0x0 0x00100000 /* controller registers */
+ 0x28 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
+ interrupts = <0 113 0x4>; /* Level high type */
+ interrupt-names = "intr";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <4>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x28 0x00010000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x28 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ msi-parent = <&its>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 0 0 114 4>,
+ <0000 0 0 2 &gic 0 0 0 115 4>,
+ <0000 0 0 3 &gic 0 0 0 116 4>,
+ <0000 0 0 4 &gic 0 0 0 117 4>;
+ };
+
+ pcie3: pcie@3600000 {
+ compatible = "fsl,ls2088a-pcie", "fsl,ls2080a-pcie",
+ "snps,dw-pcie";
+ reg = <0x00 0x03600000 0x0 0x00100000 /* controller registers */
+ 0x30 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
+ interrupts = <0 118 0x4>; /* Level high type */
+ interrupt-names = "intr";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <8>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x30 0x00010000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x30 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ msi-parent = <&its>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 0 0 119 4>,
+ <0000 0 0 2 &gic 0 0 0 120 4>,
+ <0000 0 0 3 &gic 0 0 0 121 4>,
+ <0000 0 0 4 &gic 0 0 0 122 4>;
+ };
+
+ pcie4: pcie@3700000 {
+ compatible = "fsl,ls2088a-pcie", "fsl,ls2080a-pcie",
+ "snps,dw-pcie";
+ reg = <0x00 0x03700000 0x0 0x00100000 /* controller registers */
+ 0x38 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
+ interrupts = <0 123 0x4>; /* Level high type */
+ interrupt-names = "intr";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <4>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x38 0x00010000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x38 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ msi-parent = <&its>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 0 0 124 4>,
+ <0000 0 0 2 &gic 0 0 0 125 4>,
+ <0000 0 0 3 &gic 0 0 0 126 4>,
+ <0000 0 0 4 &gic 0 0 0 127 4>;
+ };
+
+ sata0: sata@3200000 {
+ status = "disabled";
+ compatible = "fsl,ls2088a-ahci", "fsl,ls2080a-ahci";
+ reg = <0x0 0x3200000 0x0 0x10000>;
+ interrupts = <0 133 0x4>; /* Level high type */
+ clocks = <&clockgen 4 3>;
+ };
+
+ sata1: sata@3210000 {
+ status = "disabled";
+ compatible = "fsl,ls2088a-ahci", "fsl,ls2080a-ahci";
+ reg = <0x0 0x3210000 0x0 0x10000>;
+ interrupts = <0 136 0x4>; /* Level high type */
+ clocks = <&clockgen 4 3>;
+ };
+
+ usb0: usb3@3100000 {
+ status = "disabled";
+ compatible = "snps,dwc3";
+ reg = <0x0 0x3100000 0x0 0x10000>;
+ interrupts = <0 80 0x4>; /* Level high type */
+ dr_mode = "host";
+ snps,quirk-frame-length-adjustment = <0x20>;
+ };
+
+ usb1: usb3@3110000 {
+ status = "disabled";
+ compatible = "snps,dwc3";
+ reg = <0x0 0x3110000 0x0 0x10000>;
+ interrupts = <0 81 0x4>; /* Level high type */
+ dr_mode = "host";
+ snps,quirk-frame-length-adjustment = <0x20>;
+ };
+
+ ccn@4000000 {
+ compatible = "arm,ccn-504";
+ reg = <0x0 0x04000000 0x0 0x01000000>;
+ interrupts = <0 12 4>;
+ };
+ };
+};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
