Re: [PATCH v3] pinctrl: Add SX150X GPIO Extender Pinctrl Driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Sun, Oct 23, 2016 at 3:47 AM, Linus Walleij <linus.walleij@xxxxxxxxxx> wrote:
> On Sun, Oct 23, 2016 at 4:50 AM, Andrey Smirnov
> <andrew.smirnov@xxxxxxxxx> wrote:
>> On Fri, Oct 21, 2016 at 2:09 AM, Neil Armstrong <narmstrong@xxxxxxxxxxxx> wrote:
>>> Since the I2C sx150x GPIO expander driver uses platform_data to manage
>>> the pins configurations, rewrite the driver as a pinctrl driver using
>>> pinconf to get/set pin configurations from DT or debugfs.
>>>
>>> The pinctrl driver is functionnally equivalent as the gpio-only driver
>>> and can use DT for pinconf. The platform_data confirmation is dropped.
>>>
>>> This patchset removed the gpio-only driver and selects the Pinctrl driver
>>> config instead. This patchset also migrates the gpio dt-bindings to pinctrl
>>> and add the pinctrl optional properties.
>>>
>>> The driver was tested with a SX1509 device on a BeagleBone black with
>>> interrupt support and on an X86_64 machine over an I2C to USB converter.
>>>
>>> Signed-off-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
> (...)
>
>>> +               ret = gpiochip_irqchip_add(&pctl->gpio,
>>> +                                          &pctl->irq_chip, 0,
>>> +                                          handle_edge_irq, IRQ_TYPE_EDGE_BOTH);
>>
>> Adding irqchip with IRQ_TYPE_EDGE_BOTH triggers a WARN in
>> drivers/gpio/gpiolib.c:1671, on a custom Vybrid board that I have with
>> the chip, so maybe it should be replaced with IRQ_TYPE_NONE? That's
>> what I did for my testing and with that change
>
> I fixed this up when applying. It is corect, it should always be IRQ_TYPE_NONE
> unless it is a very old driver using boardfiles. The proper type is set up
> when the driver using it requests the IRQ.
>
> Some drivers also need to set the default handler to handle_bad_irq
> and then also set that up in the irqchip .set_type() callback, especially
> those hardwares that have an ACK register for edge IRQs so that a second
> edge irq can come in when handling a first edge IRQ. Level IRQs don't
> have this problem for obvious reasons, so we need to select between
> handle_edge_irq() or handle_level_irq() on these hardwares.
>
> Could you or Neil or both check if this applies to sx150x?

These chips only support edge triggered interrupts, so I doesn't seem
to me that it does. However, trying to answer that question lead me to
read IRQ related code of the driver, some of which didn't make as much
sense as I'd like it to. It may be due to my ignorance of how some of
the irqchip internals work, but I'll mention it anyway just in case.

It seem strange to me that the driver uses "handle_edge_irq", given
how none of the individual interrupts seem to require any ACKing,
since it is all handled in sx150x_irq_thread_fn(), line 533. More so,
I had trouble finding who/where sets .irq_ack() callback, which AFAIU
is mandatory for handle_edge_irq().

Unfortunately sx150x HW setup that I have doesn't permit to do any
testing of IRQ functionality (the chip is mostly used as GPO), so I
wasn't able to experiment with any of the code in question and shed
any light on my confusion. Apologies if it is just a false alarm.

Thanks,
Andrey Smirnov
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux