Add Synopsys Designware MAC Glue layer for the Oxford Semiconductor OX820. Signed-off-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx> --- .../devicetree/bindings/net/oxnas-dwmac.txt | 44 +++++ drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 ++ drivers/net/ethernet/stmicro/stmmac/Makefile | 1 + drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c | 219 +++++++++++++++++++++ 4 files changed, 275 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/oxnas-dwmac.txt create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c Changes since RFC at https://patchwork.kernel.org/patch/9387257 : - Drop init/exit callbacks - Implement proper remove and PM callback - Call init from probe - Disable/Unprepare clock if stmmac probe fails diff --git a/Documentation/devicetree/bindings/net/oxnas-dwmac.txt b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt new file mode 100644 index 0000000..5d2696c --- /dev/null +++ b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt @@ -0,0 +1,44 @@ +* Oxford Semiconductor OXNAS DWMAC Ethernet controller + +The device inherits all the properties of the dwmac/stmmac devices +described in the file stmmac.txt in the current directory with the +following changes. + +Required properties on all platforms: + +- compatible: Depending on the platform this should be one of: + - "oxsemi,ox820-dwmac" + Additionally "snps,dwmac" and any applicable more + detailed version number described in net/stmmac.txt + should be used. + +- reg: The first register range should be the one of the DWMAC + controller. + +- clocks: Should contain phandles to the following clocks +- clock-names: Should contain the following: + - "stmmaceth" - see stmmac.txt + - "gmac" - peripheral gate clock + +- oxsemi,sys-ctrl: a phandle to the system controller syscon node + +Example : + +etha: ethernet@40400000 { + compatible = "oxsemi,ox820-dwmac", "snps,dwmac"; + reg = <0x40400000 0x2000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_wake_irq"; + mac-address = [000000000000]; /* Filled in by U-Boot */ + phy-mode = "rgmii"; + + clocks = <&stdclk CLK_820_ETHA>, <&gmacclk>; + clock-names = "gmac", "stmmaceth"; + resets = <&reset RESET_MAC>; + + /* Regmap for sys registers */ + oxsemi,sys-ctrl = <&sys>; + + status = "disabled"; +}; diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig index 3818c5e..27ed913 100644 --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig @@ -62,6 +62,7 @@ config DWMAC_MESON tristate "Amlogic Meson dwmac support" default ARCH_MESON depends on OF && COMMON_CLK && (ARCH_MESON || COMPILE_TEST) + select MFD_SYSCON help Support for Ethernet controller on Amlogic Meson SoCs. @@ -69,6 +70,16 @@ config DWMAC_MESON the stmmac device driver. This driver is used for Meson6, Meson8, Meson8b and GXBB SoCs. +config DWMAC_OXNAS + tristate "Oxford Semiconductor OXNAS dwmac support" + default ARCH_OXNAS + depends on OF && COMMON_CLK && (ARCH_OXNAS || COMPILE_TEST) + help + Support for Ethernet controller on Oxford Semiconductor OXNAS SoCs. + + This selects the Oxford Semiconductor OXNASSoC glue layer support for + the stmmac device driver. This driver is used for OX820. + config DWMAC_ROCKCHIP tristate "Rockchip dwmac support" default ARCH_ROCKCHIP diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile index 5d6ece5..8f83a86 100644 --- a/drivers/net/ethernet/stmicro/stmmac/Makefile +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_STMMAC_PLATFORM) += stmmac-platform.o obj-$(CONFIG_DWMAC_IPQ806X) += dwmac-ipq806x.o obj-$(CONFIG_DWMAC_LPC18XX) += dwmac-lpc18xx.o obj-$(CONFIG_DWMAC_MESON) += dwmac-meson.o dwmac-meson8b.o +obj-$(CONFIG_DWMAC_OXNAS) += dwmac-oxnas.o obj-$(CONFIG_DWMAC_ROCKCHIP) += dwmac-rk.o obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c new file mode 100644 index 0000000..40fd845 --- /dev/null +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c @@ -0,0 +1,219 @@ +/* + * Oxford Semiconductor OXNAS DWMAC glue layer + * + * Copyright (C) 2016 Neil Armstrong <narmstrong@xxxxxxxxxxxx> + * Copyright (C) 2014 Daniel Golle <daniel@xxxxxxxxxxxxxx> + * Copyright (C) 2013 Ma Haijun <mahaijuns@xxxxxxxxx> + * Copyright (C) 2012 John Crispin <blogic@xxxxxxxxxxx> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/device.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/mfd/syscon.h> +#include <linux/stmmac.h> + +#include "stmmac_platform.h" + +/* System Control regmap offsets */ +#define OXNAS_DWMAC_CTRL_REGOFFSET 0x78 +#define OXNAS_DWMAC_DELAY_REGOFFSET 0x100 + +/* Control Register */ +#define DWMAC_CKEN_RX_IN 14 +#define DWMAC_CKEN_RXN_OUT 13 +#define DWMAC_CKEN_RX_OUT 12 +#define DWMAC_CKEN_TX_IN 10 +#define DWMAC_CKEN_TXN_OUT 9 +#define DWMAC_CKEN_TX_OUT 8 +#define DWMAC_RX_SOURCE 7 +#define DWMAC_TX_SOURCE 6 +#define DWMAC_LOW_TX_SOURCE 4 +#define DWMAC_AUTO_TX_SOURCE 3 +#define DWMAC_RGMII 2 +#define DWMAC_SIMPLE_MUX 1 +#define DWMAC_CKEN_GTX 0 + +/* Delay register */ +#define DWMAC_TX_VARDELAY_SHIFT 0 +#define DWMAC_TXN_VARDELAY_SHIFT 8 +#define DWMAC_RX_VARDELAY_SHIFT 16 +#define DWMAC_RXN_VARDELAY_SHIFT 24 +#define DWMAC_TX_VARDELAY(d) ((d) << DWMAC_TX_VARDELAY_SHIFT) +#define DWMAC_TXN_VARDELAY(d) ((d) << DWMAC_TXN_VARDELAY_SHIFT) +#define DWMAC_RX_VARDELAY(d) ((d) << DWMAC_RX_VARDELAY_SHIFT) +#define DWMAC_RXN_VARDELAY(d) ((d) << DWMAC_RXN_VARDELAY_SHIFT) + +struct oxnas_dwmac { + struct device *dev; + struct clk *clk; + struct regmap *regmap; +}; + +static int oxnas_dwmac_init(struct oxnas_dwmac *dwmac) +{ + unsigned int value; + int ret; + + /* Reset HW here before changing the glue configuration */ + ret = device_reset(dwmac->dev); + if (ret) + return ret; + + clk_prepare_enable(dwmac->clk); + + ret = regmap_read(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, &value); + if (ret < 0) + return ret; + + /* Enable GMII_GTXCLK to follow GMII_REFCLK, required for gigabit PHY */ + value |= BIT(DWMAC_CKEN_GTX); + /* Use simple mux for 25/125 Mhz clock switching */ + value |= BIT(DWMAC_SIMPLE_MUX); + /* set auto switch tx clock source */ + value |= BIT(DWMAC_AUTO_TX_SOURCE); + /* enable tx & rx vardelay */ + value |= BIT(DWMAC_CKEN_TX_OUT); + value |= BIT(DWMAC_CKEN_TXN_OUT); + value |= BIT(DWMAC_CKEN_TX_IN); + value |= BIT(DWMAC_CKEN_RX_OUT); + value |= BIT(DWMAC_CKEN_RXN_OUT); + value |= BIT(DWMAC_CKEN_RX_IN); + regmap_write(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, value); + + /* set tx & rx vardelay */ + value = DWMAC_TX_VARDELAY(4); + value |= DWMAC_TXN_VARDELAY(2); + value |= DWMAC_RX_VARDELAY(10); + value |= DWMAC_RXN_VARDELAY(8); + regmap_write(dwmac->regmap, OXNAS_DWMAC_DELAY_REGOFFSET, value); + + return 0; +} + +static int oxnas_dwmac_probe(struct platform_device *pdev) +{ + struct plat_stmmacenet_data *plat_dat; + struct stmmac_resources stmmac_res; + struct device_node *sysctrl; + struct oxnas_dwmac *dwmac; + int ret; + + sysctrl = of_parse_phandle(pdev->dev.of_node, "oxsemi,sys-ctrl", 0); + if (!sysctrl) { + dev_err(&pdev->dev, "failed to get sys-ctrl node\n"); + return -EINVAL; + } + + ret = stmmac_get_platform_resources(pdev, &stmmac_res); + if (ret) + return ret; + + plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + + dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL); + if (!dwmac) + return -ENOMEM; + + dwmac->dev = &pdev->dev; + plat_dat->bsp_priv = dwmac; + + dwmac->regmap = syscon_node_to_regmap(sysctrl); + if (IS_ERR(dwmac->regmap)) { + dev_err(&pdev->dev, "failed to have sysctrl regmap\n"); + return PTR_ERR(dwmac->regmap); + } + + dwmac->clk = devm_clk_get(&pdev->dev, "gmac"); + if (IS_ERR(dwmac->clk)) + return PTR_ERR(dwmac->clk); + + ret = oxnas_dwmac_init(dwmac); + if (ret) + return ret; + + ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); + if (ret) + clk_disable_unprepare(dwmac->clk); + + return ret; +} + +static int oxnas_dwmac_remove(struct platform_device *pdev) +{ + struct net_device *ndev = platform_get_drvdata(pdev); + struct stmmac_priv *priv = netdev_priv(ndev); + struct oxnas_dwmac *dwmac = priv->plat->bsp_priv; + int ret = stmmac_dvr_remove(&pdev->dev); + + clk_disable_unprepare(dwmac->clk); + + return ret; +} + +#ifdef CONFIG_PM_SLEEP +static int oxnas_dwmac_suspend(struct device *dev) +{ + struct net_device *ndev = dev_get_drvdata(dev); + struct stmmac_priv *priv = netdev_priv(ndev); + struct oxnas_dwmac *dwmac = priv->plat->bsp_priv; + int ret; + + ret = stmmac_suspend(dev); + clk_disable_unprepare(dwmac->clk); + + return ret; +} + +static int oxnas_dwmac_resume(struct device *dev) +{ + struct net_device *ndev = dev_get_drvdata(dev); + struct stmmac_priv *priv = netdev_priv(ndev); + struct oxnas_dwmac *dwmac = priv->plat->bsp_priv; + int ret; + + ret = oxnas_dwmac_init(dwmac); + if (ret) + return ret; + + ret = stmmac_resume(dev); + + return ret; +} +#endif /* CONFIG_PM_SLEEP */ + +static SIMPLE_DEV_PM_OPS(oxnas_dwmac_pm_ops, + oxnas_dwmac_suspend, oxnas_dwmac_resume); + +static const struct of_device_id oxnas_dwmac_match[] = { + { .compatible = "oxsemi,ox820-dwmac" }, + { } +}; +MODULE_DEVICE_TABLE(of, oxnas_dwmac_match); + +static struct platform_driver oxnas_dwmac_driver = { + .probe = oxnas_dwmac_probe, + .remove = oxnas_dwmac_remove, + .driver = { + .name = "oxnas-dwmac", + .pm = &oxnas_dwmac_pm_ops, + .of_match_table = oxnas_dwmac_match, + }, +}; +module_platform_driver(oxnas_dwmac_driver); + +MODULE_AUTHOR("Neil Armstrong <narmstrong@xxxxxxxxxxxx>"); +MODULE_DESCRIPTION("Oxford Semiconductor OXNAS DWMAC glue layer"); +MODULE_LICENSE("GPL v2"); -- 2.7.0 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
