Hi Rob,
> On Oct 10, 2016, at 23:03 , Rob Herring <robh@xxxxxxxxxx> wrote:
>
> On Fri, Oct 07, 2016 at 06:18:34PM +0300, Pantelis Antoniou wrote:
>> From: Georgi Vlaev <gvlaev@xxxxxxxxxxx>
>>
>> Add device tree bindings document for the GPIO driver of
>> Juniper's SAM FPGA.
>>
>> Signed-off-by: Georgi Vlaev <gvlaev@xxxxxxxxxxx>
>> [Ported from Juniper kernel]
>> Signed-off-by: Pantelis Antoniou <pantelis.antoniou@xxxxxxxxxxxx>
>> ---
>> .../devicetree/bindings/gpio/jnx,gpio-sam.txt | 110 +++++++++++++++++++++
>> 1 file changed, 110 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/gpio/jnx,gpio-sam.txt
>>
>> diff --git a/Documentation/devicetree/bindings/gpio/jnx,gpio-sam.txt b/Documentation/devicetree/bindings/gpio/jnx,gpio-sam.txt
>> new file mode 100644
>> index 0000000..514c350
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/gpio/jnx,gpio-sam.txt
>> @@ -0,0 +1,110 @@
>> +Juniper SAM FPGA GPIO block
>> +
>> +The controller's registers are organized as sets of eight 32-bit
>> +registers with each set controlling a bank of up to 32 pins. A single
>> +interrupt is shared for all of the banks handled by the controller.
>> +
>> +Required properties:
>> +
>> +- compatible:
>> + Must be "jnx,gpio-sam"
>> +
>> +- #gpio-cells:
>> + Should be <2>. The first cell is the pin number (within the controller's
>> + pin space), and the second is used for the following flags:
>> + bit[0]: direction (0 = out, 1 = in)
>> + bit[1]: init high
>> + bit[2]: active low
>> + bit[3]: open drain
>> + bit[4]: open drain
>
> Use and/or add to standard flags.
>
OK.
>> +
>> +- gpio-controller:
>> + Specifies that the node is a GPIO controller.
>> +
>> +Optional properties:
>> +
>> +- reg:
>> + This driver is part of the SAM FPGA MFD driver, so the
>> + address range is supplied by that driver. However you can
>> + override using this property.
>> +
>> +- gpio-base:
>> + Base of the GPIO pins of this instance. If not present use system allocated.
>
> This probably needs to go.
>
OK.
>> +
>> +- gpio-count:
>
> ngpios instead.
>
OK.
>> + Number of GPIO pins of this instance. If not present read the number from
>> + the one configured in the FPGA data. Maximum number is 512.
>> +
>> +- #interrupt-cells:
>> + Should be <2>. The first cell is the GPIO number, the second should specify
>> + flags. The following subset of flags is supported:
>> + - bits[16,4:0] trigger type and level flags
>> + bit 0: rising edge interrupt
>> + bit 1: falling edge interrupt
>> + bit 2: active high interrupt
>> + bit 3: active low interrupt
>> + bit 4: enable debounce
>> + bit 16: signal is active low
>
> What does this mean?
>
I will reword.
>> + See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
>> +
>> +- gpio-interrupts:
>> + A number of triples that define the mapping of interrupt groupsb to a range of
>> + pins. The first cell defines the interrupt group, the second is the start of
>> + the pin range and the third the number of pins in the range.
>
> Needs a vendor prefix.
>
OK.
>> +
>> +- gpio-exports:
>> + A subnode containing the list of pins that will be exported to user-space.
>
> DT doesn't know about userspace. Drop this.
>
OK, the export bit should go.
>> + Each subnode contains:
>> + Required properties:
>> + - pin: The gpio to be exported and the relevant flags.
>> + Optional properties:
>> + - label: The label to use for export; if not supplied use the node name.
>> +
>> +Example:
>> +
>> +gpio20: gpio-sam {
>> + compatible = "jnx,gpio-sam";
>> + gpio-controller;
>> + interrupt-controller;
>> + /* 1st cell: gpio pin
>> + * 2nd cell: flags (bit mask)
>> + * bit 0: rising edge interrupt
>> + * bit 1: falling edge interrupt
>> + * bit 2: active high interrupt
>> + * bit 3: active low interrupt
>> + * bit 4: enable debounce
>> + * bit 16: signal is active low
>> + */
>> + #interrupt-cells = <2>;
>> + #gpio-cells = <2>;
>> + gpio-count = <340>;
>> + /* 1st cell: gpio interrupt status bit
>> + * 2nd cell: 1st pin
>> + * 3rd cell: # of pins
>> + */
>> + gpio-interrupts =
>> + <0 0 32>, /* TL / TQ */
>> + <1 32 32>, /* PIC 1 */
>> + <2 32 32>, /* PIC 1 spare */
>> + <7 148 32>, /* PIC 0 */
>> + <8 170 32>, /* PIC 0 spare */
>> + <16 318 22>; /* FPC */
>> +
>> + gpio-exports {
>> + /*
>> + * flags:
>> + * GPIOF_DIR_IN bit 0=1
>> + * GPIOF_DIR_OUT bit 0=0
>> + * GPIOF_INIT_HIGH bit 1=1
>> + * GPIOF_INIT_HIGH is raw, not translated
>> + * GPIOF_ACTIVE_LOW bit 2=1
>> + * GPIOF_OPEN_DRAIN bit 3=1
>> + * GPIOF_OPEN_SOURCE bit 4=1
>> + * GPIOF_EXPORT bit 5=1
>> + * GPIOF_EXPORT_CHANGEABLE bit 6=1
>> + */
>> + tl0-rst {
>> + pin = < 8 0x24 >;
>> + };
>> + };
>> +};
>> --
>> 1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
