On Fri, Oct 07, 2016 at 06:18:34PM +0300, Pantelis Antoniou wrote:
> From: Georgi Vlaev <gvlaev@xxxxxxxxxxx>
>
> Add device tree bindings document for the GPIO driver of
> Juniper's SAM FPGA.
>
> Signed-off-by: Georgi Vlaev <gvlaev@xxxxxxxxxxx>
> [Ported from Juniper kernel]
> Signed-off-by: Pantelis Antoniou <pantelis.antoniou@xxxxxxxxxxxx>
> ---
> .../devicetree/bindings/gpio/jnx,gpio-sam.txt | 110 +++++++++++++++++++++
> 1 file changed, 110 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/gpio/jnx,gpio-sam.txt
>
> diff --git a/Documentation/devicetree/bindings/gpio/jnx,gpio-sam.txt b/Documentation/devicetree/bindings/gpio/jnx,gpio-sam.txt
> new file mode 100644
> index 0000000..514c350
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/jnx,gpio-sam.txt
> @@ -0,0 +1,110 @@
> +Juniper SAM FPGA GPIO block
> +
> +The controller's registers are organized as sets of eight 32-bit
> +registers with each set controlling a bank of up to 32 pins. A single
> +interrupt is shared for all of the banks handled by the controller.
> +
> +Required properties:
> +
> +- compatible:
> + Must be "jnx,gpio-sam"
> +
> +- #gpio-cells:
> + Should be <2>. The first cell is the pin number (within the controller's
> + pin space), and the second is used for the following flags:
> + bit[0]: direction (0 = out, 1 = in)
> + bit[1]: init high
> + bit[2]: active low
> + bit[3]: open drain
> + bit[4]: open drain
Use and/or add to standard flags.
> +
> +- gpio-controller:
> + Specifies that the node is a GPIO controller.
> +
> +Optional properties:
> +
> +- reg:
> + This driver is part of the SAM FPGA MFD driver, so the
> + address range is supplied by that driver. However you can
> + override using this property.
> +
> +- gpio-base:
> + Base of the GPIO pins of this instance. If not present use system allocated.
This probably needs to go.
> +
> +- gpio-count:
ngpios instead.
> + Number of GPIO pins of this instance. If not present read the number from
> + the one configured in the FPGA data. Maximum number is 512.
> +
> +- #interrupt-cells:
> + Should be <2>. The first cell is the GPIO number, the second should specify
> + flags. The following subset of flags is supported:
> + - bits[16,4:0] trigger type and level flags
> + bit 0: rising edge interrupt
> + bit 1: falling edge interrupt
> + bit 2: active high interrupt
> + bit 3: active low interrupt
> + bit 4: enable debounce
> + bit 16: signal is active low
What does this mean?
> + See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> +
> +- gpio-interrupts:
> + A number of triples that define the mapping of interrupt groupsb to a range of
> + pins. The first cell defines the interrupt group, the second is the start of
> + the pin range and the third the number of pins in the range.
Needs a vendor prefix.
> +
> +- gpio-exports:
> + A subnode containing the list of pins that will be exported to user-space.
DT doesn't know about userspace. Drop this.
> + Each subnode contains:
> + Required properties:
> + - pin: The gpio to be exported and the relevant flags.
> + Optional properties:
> + - label: The label to use for export; if not supplied use the node name.
> +
> +Example:
> +
> +gpio20: gpio-sam {
> + compatible = "jnx,gpio-sam";
> + gpio-controller;
> + interrupt-controller;
> + /* 1st cell: gpio pin
> + * 2nd cell: flags (bit mask)
> + * bit 0: rising edge interrupt
> + * bit 1: falling edge interrupt
> + * bit 2: active high interrupt
> + * bit 3: active low interrupt
> + * bit 4: enable debounce
> + * bit 16: signal is active low
> + */
> + #interrupt-cells = <2>;
> + #gpio-cells = <2>;
> + gpio-count = <340>;
> + /* 1st cell: gpio interrupt status bit
> + * 2nd cell: 1st pin
> + * 3rd cell: # of pins
> + */
> + gpio-interrupts =
> + <0 0 32>, /* TL / TQ */
> + <1 32 32>, /* PIC 1 */
> + <2 32 32>, /* PIC 1 spare */
> + <7 148 32>, /* PIC 0 */
> + <8 170 32>, /* PIC 0 spare */
> + <16 318 22>; /* FPC */
> +
> + gpio-exports {
> + /*
> + * flags:
> + * GPIOF_DIR_IN bit 0=1
> + * GPIOF_DIR_OUT bit 0=0
> + * GPIOF_INIT_HIGH bit 1=1
> + * GPIOF_INIT_HIGH is raw, not translated
> + * GPIOF_ACTIVE_LOW bit 2=1
> + * GPIOF_OPEN_DRAIN bit 3=1
> + * GPIOF_OPEN_SOURCE bit 4=1
> + * GPIOF_EXPORT bit 5=1
> + * GPIOF_EXPORT_CHANGEABLE bit 6=1
> + */
> + tl0-rst {
> + pin = < 8 0x24 >;
> + };
> + };
> +};
> --
> 1.9.1
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
