Re: [PATCH v2 2/3] input: pwm-beeper: add documentation for volume devicetree bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Tue, Oct 11, 2016 at 3:17 AM, Schrempf Frieder
<frieder.schrempf@xxxxxxxxx> wrote:
> On 10.10.2016 17:20, Rob Herring wrote:
>> On Fri, Oct 07, 2016 at 09:08:17AM +0000, Schrempf Frieder wrote:
>>> This patch adds the documentation for the devicetree bindings to set
>>> the volume levels.
>>>
>>> Signed-off-by: Frieder Schrempf <frieder.schrempf@xxxxxxxxx>
>>> ---
>>> Changes in v2:
>>>  - split into 3 separate patches
>>>  - make volume properties optional
>>>
>>>  .../devicetree/bindings/input/pwm-beeper.txt       | 22 ++++++++++++++++++++++
>>>  1 file changed, 22 insertions(+)
>>>
>>> diff --git a/Documentation/devicetree/bindings/input/pwm-beeper.txt b/Documentation/devicetree/bindings/input/pwm-beeper.txt
>>> index be332ae..6d8ba4e 100644
>>> --- a/Documentation/devicetree/bindings/input/pwm-beeper.txt
>>> +++ b/Documentation/devicetree/bindings/input/pwm-beeper.txt
>>> @@ -5,3 +5,25 @@ Registers a PWM device as beeper.
>>>  Required properties:
>>>  - compatible: should be "pwm-beeper"
>>>  - pwms: phandle to the physical PWM device
>>> +
>>> +Optional properties:
>>> +- volume-levels: Array of distinct volume levels. These need to be in the
>>> +      range of 0 to 500, while 0 means 0% duty cycle (mute) and 500 means
>>> +      50% duty cycle (max volume).
>>> +      Please note that the actual volume of most beepers is highly
>>> +      non-linear, which means that low volume levels are probably somewhere
>>> +      in the range of 1 to 30 (0.1-3% duty cycle).
>>
>> What does the index correspond to? The linear volume?
>
> In most cases users probably need linear volume levels (e.g. 0%, 25%,
> 50%, 75%, 100%) and in this case the index would indeed correspond to
> the linear perceived volume.
>
> But also non-linear relations are possible (e.g. 0%, 20%, 100%), if the
> user needs for example "mute", "low", "high" as volume levels.

Exclude off/mute and this is still linear. Also, the user exposed
levels could be a subset of the defined h/w levels. That should be
independent of DT.

> The linearization (defining the corresponding duty cycle for each index)
> depends on the beeper and the perception of the user.

This has to be a consistent interface across h/w to have a userspace
that can work across h/w. For that, you have to define the binding as
linear. Of course, it's all measured by perception and not completely
accurate which is fine.

> For the example array definition below, I tried different duty cycles
> and found values of 0.8%, 2%, 4%, 50% to be approximately correspondent
> to perceived volume levels of 25%, 50%, 75%, 100% in my case.
>
>>
>>> +- default-volume-level: the default volume level (index into the
>>> +      array defined by the "volume-levels" property)
>>> +
>>> +The volume level can be set via sysfs under /sys/class/input/inputX/volume.
>>> +The maximum volume level index can be read from /sys/class/input/inputX/max_volume_level.

Also, drop this. Not relevant to the binding.

Rob
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux