Hi Adrian,
On 10/10/2016 3:53 PM, Adrian Hunter wrote:
On 10/10/16 13:16, Adrian Hunter wrote:
On 05/10/16 17:40, Ritesh Harjani wrote:
sdhci-msm controller may have different clk-rates for each
bus speed mode. Thus implement set_clock callback for
sdhci-msm driver.
Signed-off-by: Sahitya Tummala <stummala@xxxxxxxxxxxxxx>
Signed-off-by: Ritesh Harjani <riteshh@xxxxxxxxxxxxxx>
---
drivers/mmc/host/sdhci-msm.c | 110 ++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 109 insertions(+), 1 deletion(-)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index 542ddad..9d18cf0 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -84,6 +84,7 @@ struct sdhci_msm_host {
struct clk *bus_clk; /* SDHC bus voter clock */
u32 *clk_table;
int clk_table_sz;
+ u32 clk_rate;
struct mmc_host *mmc;
bool use_14lpp_dll_reset;
};
@@ -588,6 +589,113 @@ static unsigned int sdhci_msm_get_min_clock(struct sdhci_host *host)
}
}
+static unsigned int sdhci_msm_get_msm_clk_rate(struct sdhci_host *host,
+ u32 req_clk)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
+ int count;
+ unsigned int sel_clk = -1;
+
+ if (!msm_host->clk_table)
+ return clk_round_rate(msm_host->clk, ULONG_MAX);
+
+ count = msm_host->clk_table_sz;
+
+ while (count--) {
+ sel_clk = msm_host->clk_table[count];
+ if (req_clk >= sel_clk)
+ return sel_clk;
+ }
+
+ return sel_clk;
+}
+
+/**
+ * __sdhci_msm_set_clock - sdhci_msm clock control.
+ *
+ * Description:
+ * Implement MSM version of sdhci_set_clock.
+ * This is required since MSM controller does not
+ * use internal divider and instead directly control
+ * the GCC clock as per HW recommendation.
+ **/
+void __sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
+{
+ u16 clk;
+ unsigned long timeout;
+
+ /*
+ * Keep actual_clock as zero -
+ * - since there is no divider used so no need of having actual_clock.
+ * - MSM controller uses SDCLK for data timeout calculation. If
+ * actual_clock is zero, host->clock is taken for calculation.
+ */
+ host->mmc->actual_clock = 0;
+
+ sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
+
+ if (clock == 0)
+ return;
+
+ /*
+ * MSM controller do not use clock divider.
+ * Thus read SDHCI_CLOCK_CONTROL and only enable
+ * clock with no divider value programmed.
+ */
+ clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+
+ clk |= SDHCI_CLOCK_INT_EN;
+ sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
+
+ /* Wait max 20 ms */
+ timeout = 20;
+ while (!((clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL))
+ & SDHCI_CLOCK_INT_STABLE)) {
+ if (timeout == 0) {
+ pr_err("%s: Internal clock never stabilised.\n",
+ mmc_hostname(host->mmc));
+ return;
+ }
+ timeout--;
+ mdelay(1);
+ }
+
+ clk |= SDHCI_CLOCK_CARD_EN;
+ sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
+}
+
+static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
+ u32 msm_clock;
+ int rc;
+
+ if (!clock)
Wouldn't you still need to set msm_host->clk_rate = clock in this case
Yes. Will do that.
+ goto out;
+
+ spin_unlock_irq(&host->lock);
+ if ((clock != msm_host->clk_rate) && msm_host->clk_table) {
+ msm_clock = sdhci_msm_get_msm_clk_rate(host, clock);
+ rc = clk_set_rate(msm_host->clk, msm_clock);
+ if (rc) {
+ pr_err("%s: failed to set clock at rate %u, requested clock rate %u\n",
+ mmc_hostname(host->mmc), msm_clock, clock);
+ goto out;
'goto out' leaves spinlock unlocked
Thanks for catching it.
+ }
+ msm_host->clk_rate = clock;
+ pr_debug("%s: setting clock at rate %lu\n",
+ mmc_hostname(host->mmc), clk_get_rate(msm_host->clk));
+ }
+
+ spin_lock_irq(&host->lock);
+out:
+ if (!msm_host->clk_table)
+ return sdhci_set_clock(host, clock);
Could put the above 2 lines at the start and then no need to check
msm_host->clk_table again.
I wanted to make this change, but then may be because of later patches
which modifies sdhci_msm_set_clock for UHS modes, I did not move this to
top.
I reviewed that part again, I will make the necessary changes.
Thanks.
+ __sdhci_msm_set_clock(host, clock);
+}
+
static const struct of_device_id sdhci_msm_dt_match[] = {
{ .compatible = "qcom,sdhci-msm-v4" },
{},
@@ -598,7 +706,7 @@ MODULE_DEVICE_TABLE(of, sdhci_msm_dt_match);
static const struct sdhci_ops sdhci_msm_ops = {
.platform_execute_tuning = sdhci_msm_execute_tuning,
.reset = sdhci_reset,
- .set_clock = sdhci_set_clock,
+ .set_clock = sdhci_msm_set_clock,
.get_min_clock = sdhci_msm_get_min_clock,
.get_max_clock = sdhci_msm_get_max_clock,
.set_bus_width = sdhci_set_bus_width,
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html