From: Steve Twiss <stwiss.opensource@xxxxxxxxxxx> Extend existing DA9062 binding information to include the DA9061 PMIC for MFD core and regulators. Add a da9062-onkey link to the existing onkey binding file. Add a da9062-thermal link to the new temperature monitoring binding file found in [PATCH V1 8/10]. Delete the da9062-watchdog section and replace it with a link to the new DA9061/62 binding information file added by [PATCH V1 7/10]. Signed-off-by: Steve Twiss <stwiss.opensource@xxxxxxxxxxx> --- This patch applies against linux-next and v4.8 Hi, This patch depends on acceptance of the main code for the DA9061 MFD: - [PATCH V1 1/10] mfd: da9061: MFD core support and also from the following binding file changes: - [PATCH V1 6/10] Binding for onkey - [PATCH V1 7/10] Binding for watchdog - [PATCH V1 8/10] Binding for thermal Regards, Steve Twiss, Dialog Semiconductor Ltd. Documentation/devicetree/bindings/mfd/da9062.txt | 45 +++++++++++++++++------- 1 file changed, 33 insertions(+), 12 deletions(-) diff --git a/Documentation/devicetree/bindings/mfd/da9062.txt b/Documentation/devicetree/bindings/mfd/da9062.txt index 38802b5..38ba5e2 100644 --- a/Documentation/devicetree/bindings/mfd/da9062.txt +++ b/Documentation/devicetree/bindings/mfd/da9062.txt @@ -1,22 +1,32 @@ * Dialog DA9062 Power Management Integrated Circuit (PMIC) -DA9062 consists of a large and varied group of sub-devices: +The DA9062 driver is compatible with the DA9062 and DA9061 devices. + +Product information can be found here: +- http://www.dialog-semiconductor.com/products/da9062 +- http://www.dialog-semiconductor.com/products/da9061 + +DA9062 driver consists of a large and varied group of sub-devices: Device Supply Names Description ------ ------------ ----------- da9062-regulator : : LDOs & BUCKs da9062-rtc : : Real-Time Clock +da9062-onkey : : On Key da9062-watchdog : : Watchdog Timer +da9062-thermal : : Thermal ====== Required properties: -- compatible : Should be "dlg,da9062". +- compatible : Should be + "dlg,da9062" for DA9062 + "dlg,da9061" for DA9061 - reg : Specifies the I2C slave address (this defaults to 0x58 but it can be modified to match the chip's OTP settings). - interrupt-parent : Specifies the reference to the interrupt controller for - the DA9062. + the DA9062 or DA9061. - interrupts : IRQ line information. - interrupt-controller @@ -25,8 +35,8 @@ further information on IRQ bindings. Sub-nodes: -- regulators : This node defines the settings for the LDOs and BUCKs. The - DA9062 regulators are bound using their names listed below: +- regulators : This node defines the settings for the LDOs and BUCKs. + The DA9062 regulators are bound using their names listed below: buck1 : BUCK_1 buck2 : BUCK_2 @@ -37,6 +47,16 @@ Sub-nodes: ldo3 : LDO_3 ldo4 : LDO_4 + The DA9061 regulators are bound using their names listed below: + + buck1 : BUCK_1 + buck2 : BUCK_2 + buck3 : BUCK_3 + ldo1 : LDO_1 + ldo2 : LDO_2 + ldo3 : LDO_3 + ldo4 : LDO_4 + The component follows the standard regulator framework and the bindings details of individual regulator device can be found in: Documentation/devicetree/bindings/regulator/regulator.txt @@ -46,9 +66,14 @@ Sub-nodes: with the DA9062. There are currently no entries in this binding, however compatible = "dlg,da9062-rtc" should be added if a node is created. -- watchdog: This node defines the settings for the watchdog driver associated - with the DA9062 PMIC. The compatible = "dlg,da9062-watchdog" should be added - if a node is created. + +- onkey : See ../input/da9062-onkey.txt + + +- watchdog: See ../watchdog/da9062-watchdog.txt + + +- thermal : See ../thermal/da9062-thermal.txt Example: @@ -64,10 +89,6 @@ Example: compatible = "dlg,da9062-rtc"; }; - watchdog { - compatible = "dlg,da9062-watchdog"; - }; - regulators { DA9062_BUCK1: buck1 { regulator-name = "BUCK1"; -- end-of-patch for PATCH V1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
