On 9/4/2016 2:32 PM, Martin Blumenstingl wrote:
> From: Jerome Brunet <jbrunet@xxxxxxxxxxxx>
>
> Add compatible strings for amlogic Meson8b and GXBB SoCs with the
> corresponding configuration parameters.
>
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
> Signed-off-by: Jerome Brunet <jbrunet@xxxxxxxxxxxx>
> ---
> Documentation/devicetree/bindings/usb/dwc2.txt | 2 ++
> drivers/usb/dwc2/platform.c | 34 ++++++++++++++++++++++++++
> 2 files changed, 36 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt
> index 20a68bf..2c30a54 100644
> --- a/Documentation/devicetree/bindings/usb/dwc2.txt
> +++ b/Documentation/devicetree/bindings/usb/dwc2.txt
> @@ -10,6 +10,8 @@ Required properties:
> - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc;
> - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs;
> - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs;
> + - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs;
> + - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs;
> - snps,dwc2: A generic DWC2 USB controller with default parameters.
> - reg : Should contain 1 register range (address and length)
> - interrupts : Should contain 1 interrupt
> diff --git a/drivers/usb/dwc2/platform.c b/drivers/usb/dwc2/platform.c
> index fc6f525..8f7b34c 100644
> --- a/drivers/usb/dwc2/platform.c
> +++ b/drivers/usb/dwc2/platform.c
> @@ -181,6 +181,38 @@ static const struct dwc2_core_params params_ltq = {
> .hibernation = -1,
> };
>
> +static const struct dwc2_core_params params_amlogic = {
> + .otg_cap = DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE,
> + .otg_ver = -1,
> + .dma_enable = 1,
> + .dma_desc_enable = 0,
> + .dma_desc_fs_enable = 0,
> + .speed = DWC2_SPEED_PARAM_HIGH,
> + .enable_dynamic_fifo = 1,
> + .en_multiple_tx_fifo = -1,
> + .host_rx_fifo_size = 512,
> + .host_nperio_tx_fifo_size = 500,
> + .host_perio_tx_fifo_size = 500,
> + .max_transfer_size = -1,
> + .max_packet_count = -1,
> + .host_channels = 16,
> + .phy_type = DWC2_PHY_TYPE_PARAM_UTMI,
> + .phy_utmi_width = -1,
> + .phy_ulpi_ddr = -1,
> + .phy_ulpi_ext_vbus = -1,
> + .i2c_enable = -1,
> + .ulpi_fs_ls = -1,
> + .host_support_fs_ls_low_power = -1,
> + .host_ls_low_power_phy_clk = -1,
> + .ts_dline = -1,
> + .reload_ctl = 1,
> + .ahbcfg = GAHBCFG_HBSTLEN_INCR8 <<
> + GAHBCFG_HBSTLEN_SHIFT,
> + .uframe_sched = 0,
> + .external_id_pin_ctl = -1,
> + .hibernation = -1,
> +};
> +
> /*
> * Check the dr_mode against the module configuration and hardware
> * capabilities.
> @@ -464,6 +496,8 @@ static const struct of_device_id dwc2_of_match_table[] = {
> { .compatible = "lantiq,xrx200-usb", .data = ¶ms_ltq },
> { .compatible = "snps,dwc2", .data = NULL },
> { .compatible = "samsung,s3c6400-hsotg", .data = NULL},
> + { .compatible = "amlogic,meson8b-usb", .data = ¶ms_amlogic },
> + { .compatible = "amlogic,meson-gxbb-usb", .data = ¶ms_amlogic },
> {},
> };
> MODULE_DEVICE_TABLE(of, dwc2_of_match_table);
>
Hi,
I have a patch series in the works that deprecates the usage of these
static parameters in favor of devicetree properties. I'll try to push
it out soon. I would rather not see any more static params structures
in the driver so hopefully we can make it work for your platform.
Regards,
John
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
