On Tue, Aug 16, 2016 at 6:28 PM, Sebastian Reichel <sre@xxxxxxxxxx> wrote:
> Hi Rob,
>
> On Tue, Aug 16, 2016 at 08:51:55AM -0500, Rob Herring wrote:
>> On Sat, Aug 13, 2016 at 05:14:34AM +0200, Sebastian Reichel wrote:
>> > ---
>> > .../devicetree/bindings/net/nokia-bluetooth.txt | 43 ++++++++++++++++++++++
>> > 1 file changed, 43 insertions(+)
>> > create mode 100644 Documentation/devicetree/bindings/net/nokia-bluetooth.txt
>> >
>> > diff --git a/Documentation/devicetree/bindings/net/nokia-bluetooth.txt b/Documentation/devicetree/bindings/net/nokia-bluetooth.txt
>> > new file mode 100644
>> > index 000000000000..a0fceabb4cce
>> > --- /dev/null
>> > +++ b/Documentation/devicetree/bindings/net/nokia-bluetooth.txt
>> > @@ -0,0 +1,43 @@
>> > +Nokia bluetooth UART devices
>> > +------
>> > +
>> > +Some vendors have custom versions of their chips, that can be found in Nokia
>> > +devices. These chips are controlled differently, than the non-Nokia version,
>> > +so a different binding is required. All chips listed here implement the Nokia
>> > +H4+ protocol.
>> > +
>> > +Required properties:
>> > +
>> > + - compatible: should be one of the following:
>> > + * "nokia,brcm,bcm2048"
>> > + * "nokia,ti,wl1271-bluetooth"
>>
>> Perhaps these should be 2 separate strings. Something like
>> '"nokia,n900-bt", "brcm,bcm2048"'. However, if they are in no way
>> compatible with the default version from the vendors, then just a single
>> string is fine, but it doesn't need to be aligned to the vendor
>> compatible string. So just "nokia,n900-bcm2048" or similar is fine.
>
> The default bcm2048 variant uses different initialization process
> and does not use word alignment as far as I know. I think having
> "brcm,bcm2048" in the compatible string is wrong.
Okay.
> I guess "brcm,bcm2048-nokia" would also be an option, since the
> chip has been built buy broadcom, but it has a custom Nokia
> interface.
That would be okay. Though, in theory Nokia could have different
products with bcm2048 all with different versions.
I was going with defining it as a board level compatible string. Even
if chips are the same, s/w can need to know board level differences so
using the board vendor and name are common.
>> > + - reset-gpios: Should specify the gpio for bluetooth reset
>> > + - host-wakeup-gpios: Should specify the gpio for host wakeup
>>
>> Should be interrupt instead?
>
> Yes this is mostly an interrupt, but I need to read the current
> line state.
When? If the interrupt is level triggered, then you can get the line
state based on whether you get an interrupt or not. If this needs to
be a wakeup source (see the wakeup source binding), then it needs to
be an interrupt.
Reading the line state is a common problem. It would be nice if the
irq API provided a function to read the line state though that is not
always possible.
>
>> > + - bluetooth-wakeup-gpios: Should specify the gpio for bluetooth wakeup
>>
>> State direction and active state for gpios.
>
> ok.
>
>> > + - clock-names: Should be "sysclk"
>> > + - clocks: Should contain a clock phandle for system clock
>> > +
>> > +Example:
>> > +
>> > +/ {
>> > + /* controlled (enabled/disabled) directly by wl1271 */
>> > + vctcxo: vctcxo {
>> > + compatible = "fixed-clock";
>> > + #clock-cells = <0>;
>> > + clock-frequency = <38400000>;
>> > + };
>> > +};
>> > +
>> > +&uart2 {
>>
>> I want to see a common serial device binding doc before accepting any
>> device bindings. It's not going to say much initially other than devices
>> are child nodes of uarts. Perhaps something on baudrate settings.
>
> Neil added a short sentence about this in "[RFC 2/7] tty: add
> support for "tty slave" devices". I just took the unmodified patch
> from Neil (*), so it's not in its own patch.
But that is in the 8250 binding. It needs to be a common binding.
Rob
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
