This is an attempt to resurrect the mainline WNR854T support (I had no luck getting a non-DT kernel to boot). First 2 patches are trivial, the next 3 add DT bindings for the SoC, then the old board file is swapped out for DT. The final 3 patches configure the PHY leds as Netgear intended. There's one major flaw; unicast traffic is never received on any port. Broadcast traffic is received however, and on the correct port. Thus an external machine can make an ARP request and get a response, for example. With a manually-entered ARP entry, the router can send pings out to a remote machine which responds, and the response is lost in the DSA switch. "ethtool -S" reports pings received on "in_unicast" but nothing makes it through the switch. This thread[0] seems very similar. I've run out of ideas here and can't find any switch datasheets to give me pointers so any suggestions greatly appreciated. I've not tried to move the PCI support into DT yet. Are there other branches that tackle this already? Patch 8 is the least-intrusive patch I could think of to find the PHY node, but I'm not sure it's the best approach. I tried to get dsa_slave_phy_connect() to wire up the OF node correctly[1], but doing this properly would require changes to the mdiobus api, any exposed methods register all nodes in an MDIO bus node, which doesn't exist in this case. Applied against v4.6 mainline, .config: http://jamie.lentin.co.uk/devices/netgear-wnr854t/wnr854t-support-v0a/kernel-config.txt Log output: http://jamie.lentin.co.uk/devices/netgear-wnr854t/wnr854t-support-v0a/u-boot.dmesg.txt The patchset is also available here: https://github.com/lentinj/linux/commits/wnr854t-support-v0a To use the supplied PCI Wifi card see the following patch: https://github.com/lentinj/linux/commit/d6b7b4695b7dcbf36d0663aea9cb4ecd65a1ada8 ...but this is probably a matter for another thread. Cheers, [0] http://thread.gmane.org/gmane.linux.network/120616/focus=121320 [1] https://github.com/lentinj/linux/commit/a4bceebb08ecdc25a4d49e23f2abad214868460e Jamie Lentin (10): arm: orion5x: Add required properties for orion-wdt to DT node arm: orion5x: Add documentation for SoC and board bindings arm: orion5x: Add clk support for mv88f5181 arm: orion5x: Generalise mv88f5181l pinctrl support for 88f5181 arm: orion5x: Add DT include for mv88f5181 arm: orion5x: Add DT-based support for Netgear WNR854T arm: orion5x: Remove old non-DT-based WNR854T support net: phy: Try looking for a phy-handle property to find the OF node net: phy: Re-attempt custom DT configuration after configuration arm: orion5x: Configure Netgear WNR854T network port LEDs .../bindings/arm/marvell/marvell,orion5x.txt | 25 +++ .../devicetree/bindings/clock/mvebu-core-clock.txt | 1 + .../bindings/pinctrl/marvell,orion-pinctrl.txt | 4 +- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/orion5x-mv88f5181.dtsi | 35 +++ arch/arm/boot/dts/orion5x-netgear-wnr854t.dts | 245 +++++++++++++++++++++ arch/arm/boot/dts/orion5x.dtsi | 3 +- arch/arm/mach-orion5x/Kconfig | 6 + arch/arm/mach-orion5x/Makefile | 2 +- arch/arm/mach-orion5x/board-wnr854t.c | 78 +++++++ arch/arm/mach-orion5x/wnr854t-setup.c | 185 ---------------- drivers/clk/mvebu/orion.c | 70 ++++++ drivers/net/phy/marvell.c | 26 ++- drivers/pinctrl/mvebu/pinctrl-orion.c | 23 +- 14 files changed, 498 insertions(+), 206 deletions(-) create mode 100644 Documentation/devicetree/bindings/arm/marvell/marvell,orion5x.txt create mode 100644 arch/arm/boot/dts/orion5x-mv88f5181.dtsi create mode 100644 arch/arm/boot/dts/orion5x-netgear-wnr854t.dts create mode 100644 arch/arm/mach-orion5x/board-wnr854t.c delete mode 100644 arch/arm/mach-orion5x/wnr854t-setup.c -- 2.8.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
