Re: [PATCH v3] xen/arm: enable clocks used by the hypervisor

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Mike,

On 08/07/16 18:06, Michael Turquette wrote:
Quoting Julien Grall (2016-07-08 02:34:43)
Hi Dirk,

On 08/07/16 08:44, Dirk Behme wrote:
Xen hypervisor drivers might replace native OS drivers. The result is
that some important clocks that are enabled by the OS in the non-Xen
case are not properly enabled in the presence of Xen. The clocks
property enumerates the clocks that must be enabled by the Xen clock
consumer.

An example is a serial driver enabled by the hypervisor. Xen must

I would say "An example is the UART used by the hypervisor."

consume and enable these clocks in the OS to ensure behavior continues
after firmware configures the UART hardware and corresponding clock
harder.

What do you mean by "harder"?

Also, relying on DOM0 to enable the clock looks very wrong to me and you
give an example which prove that. The UART will be used before hand by
Xen, however it will not be possible to use it if you expect DOM0 to
enable the clock (or even modify the clock frequency).

The clock should be enabled either by the firmware or Xen. But not DOM0.
DOM0 should not touch this clock at all.

Furthermore, this property could be used for clock associated to device
that will be passthrough-ed to a guest. In this case, the clock would be
enabled even if the device is not in use which will result more power
consumption.

Is there a need to pass clock references through to guests? If so the
unmerged CLK_ENABLE_HAND_OFF[0] feature might be useful to you? If this
flag is set on a given clk, it will be enabled at the time it is
registered by the clk provider driver, and it's enable_count reference
counter will be "handed off" to the first consumer that calls clk_get()
and clk_prepare_enable() on it. This means the clock CAN be gated by
it's proper driver, but it will be enabled at boot time as well.

Some driver requires to have the clock in hand to be able to configure the clock (such as setting the rate). So we would have to find a way to let the guest using the clock either by assigning the clock or some PV clock driver.

However, platform device passthrough (i.e non-pci device) cannot be done generically. The user has to provide a lots of information manually (such as MMIO, IRQ, device tree node...). So I am not sure if we want to have a generic solution here.

I though it would be worth to mention it because we may (or not) use this clock to tell DOM0 (don't touch it).

This is useful for use cases like splash screens where the bootloader
configures the display and plays some animation, and we want the linux
kernel to take over the display controller hardware without cutting
clocks, blanking or reseting it. Handing off the clock reference count
helps achieve this.

From my understanding, any device used by Xen would be in a similar situation, although there will be no driver in Linux. The current patch (as well as the v4) is calling clk_prepare_enable for each clock used by Xen. Could enabling the clock create unexpected behavior such as the UART loosing/dropping characters?

Regards,

--
Julien Grall
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux