Re: [PATCH 1/6] binding-doc: power: pwrseq-generic: add binding doc for generic power sequence library

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Am Donnerstag, den 07.07.2016, 17:14 +0800 schrieb Peter Chen:
> Add binding doc for generic power sequence library.
> 
> Signed-off-by: Peter Chen <peter.chen@xxxxxxx>
> ---
>  .../bindings/power/pwrseq/pwrseq-generic.txt       | 56 ++++++++++++++++++++++
>  1 file changed, 56 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt
> 
> diff --git a/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt
> new file mode 100644
> index 0000000..4b23834
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt
> @@ -0,0 +1,56 @@
> +The generic power sequence library
> +
> +Some hard-wired USB/MMC devices need to do power sequence to let the
> +device work normally, the typical power sequence like: enable USB
> +PHY clock, toggle reset pin, etc. But current Linux USB driver
> +lacks of such code to do it, it may cause some hard-wired USB devices
> +works abnormal or can't be recognized by controller at all. The
> +power sequence will be done before this device can be found at USB
> +bus.
> +
> +The power sequence properties is under the device node.
> +
> +Required properties:
> +- power-sequence: this device needs to do power sequence before enumeration
> +
> +Optional properties:
> +- clocks: the input clock for device.
> +- clock-name: must be "pwrseq-clk"

The "-clk" in the clock name is redundant.

> +- pwrseq-reset-gpios: Should specify the GPIO for reset.
> +- pwrseq-reset-duration-us: the duration in microsecond for assert reset signal.

I understand you want to make it explicit that this GPIO is for the
pwrseq library, but are we really gaining anything over just calling
these reset-gpios and reset-duration-us?
The same applies to the clock name above.

> +Below is the example of USB power sequence properties on USB device
> +nodes which have two level USB hubs.
> +
> +&usbotg1 {
> +	vbus-supply = <&reg_usb_otg1_vbus>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usb_otg1_id>;
> +	status = "okay";
> +
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	hub: genesys@1 {
> +		compatible = "usb5e3,608";
> +		reg = <1>;
> +
> +		power-sequence;
> +		clocks = <&clks IMX6SX_CLK_CKO>;
> +		clock-names = "pwrseq-clk";
> +		pwrseq-reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* hub reset pin */
> +		pwrseq-reset-duration-us = <10>;
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		ethernet: asix@1 {
> +			compatible = "usbb95,1708";
> +			reg = <1>;
> +
> +			power-sequence;
> +			clocks = <&clks IMX6SX_CLK_IPG>;
> +			clock-names = "pwrseq-clk";
> +			pwrseq-reset-gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* ethernet_rst */
> +			pwrseq-reset-duration-us = <15>;
> +		};

This looks weird. The hub and ethernet chips don't have "pwrseq" clock
and reset input pins. I'd remove the clock-names and pwrseq- reset
prefix.

regards
Philipp

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux