[PATCH 1/6] binding-doc: power: pwrseq-generic: add binding doc for generic power sequence library

[Peter Chen <peter.chen@xxxxxxx>]

Add binding doc for generic power sequence library.

Signed-off-by: Peter Chen <peter.chen@xxxxxxx>
---
 .../bindings/power/pwrseq/pwrseq-generic.txt       | 56 ++++++++++++++++++++++
 1 file changed, 56 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt

diff --git a/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt
new file mode 100644
index 0000000..4b23834
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt
@@ -0,0 +1,56 @@
+The generic power sequence library
+
+Some hard-wired USB/MMC devices need to do power sequence to let the
+device work normally, the typical power sequence like: enable USB
+PHY clock, toggle reset pin, etc. But current Linux USB driver
+lacks of such code to do it, it may cause some hard-wired USB devices
+works abnormal or can't be recognized by controller at all. The
+power sequence will be done before this device can be found at USB
+bus.
+
+The power sequence properties is under the device node.
+
+Required properties:
+- power-sequence: this device needs to do power sequence before enumeration
+
+Optional properties:
+- clocks: the input clock for device.
+- clock-name: must be "pwrseq-clk"
+- pwrseq-reset-gpios: Should specify the GPIO for reset.
+- pwrseq-reset-duration-us: the duration in microsecond for assert reset signal.
+
+Below is the example of USB power sequence properties on USB device
+nodes which have two level USB hubs.
+
+&usbotg1 {
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1_id>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	hub: genesys@1 {
+		compatible = "usb5e3,608";
+		reg = <1>;
+
+		power-sequence;
+		clocks = <&clks IMX6SX_CLK_CKO>;
+		clock-names = "pwrseq-clk";
+		pwrseq-reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* hub reset pin */
+		pwrseq-reset-duration-us = <10>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		ethernet: asix@1 {
+			compatible = "usbb95,1708";
+			reg = <1>;
+
+			power-sequence;
+			clocks = <&clks IMX6SX_CLK_IPG>;
+			clock-names = "pwrseq-clk";
+			pwrseq-reset-gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* ethernet_rst */
+			pwrseq-reset-duration-us = <15>;
+		};
+	};
+};
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html