Re: [PATCH] ARM: sun8i: Add Parrot Board DTS

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Tue, Jun 21, 2016 at 2:35 AM, Maxime Ripard
<maxime.ripard@xxxxxxxxxxxxxxxxxx> wrote:
> On Tue, Jun 21, 2016 at 12:30:25AM +0800, Chen-Yu Tsai wrote:
>> >> >>> +&reg_aldo1 {
>> >> >>> +       regulator-always-on;
>> >> >>> +       regulator-min-microvolt = <3000000>;
>> >> >>> +       regulator-max-microvolt = <3000000>;
>> >> >>> +       regulator-name = "aldo1";
>> >> >>
>> >> >> What is this for exactly? Would turning it off render the system inoperable?
>> >> >> How was it referenced in the fex file?
>> >> >>
>> >> >> If this is for WiFi I/O VCC, then you should specify it in mmc1 with
>> >> >> vqmmc-supply.
>> >> >>
>> >> >
>> >> > In the fex, aldo1 is one of the three power inputs for the WiFi (the
>> >> > others being dldo1 and dldo2) and in the schematics it is linked to
>> >> > both VCC-USB and VCC-IO-WIFI.
>> >> >
>> >> > I tried to turn it off and, indeed, the system becomes inoperable.
>> >> >
>> >> > I'll add vqmmc-supply in mmc1 with aldo1 regulator. However, I am
>> >> > wondering what to put in vmmc-supply for mmc1 since the WiFi module has
>> >> > three power inputs: dldo1, dldo2 and aldo1. In the fex, they are
>> >> > referenced as, respectively, module_power1, module_power2 and
>> >> > module_power3 and in the schematics dldo1 and dldo2 are named VCC-WIFI
>> >> > while aldo1 is used for VCC-IO-WIFI (if it can help in any way).
>> >> >
>> >> > VCC-WIFI is connected to pin VBAT of the Broadcom AP6212 WiFi chip.
>> >> > VCC-IO-WIFI is connected to pin VDDIO of the chip.
>> >>
>> >> VCC-IO-WIFI is vqmmc, and VCC-WIFI is vmmc.
>> >
>> > Isn't vmmc supposed to be always powered at 3.3v, and vqmmc the one
>> > used to drop to 1.8V with the UHS cards?
>>
>> For eMMC, vmmc and vqmmc correspond to the pins on the eMMC chip.
>> vmmc provides power to the internals, while vqmmc provides power to the
>> I/O buffers on both sides. With SD this is a bit less clear. IIUC the SD
>> card itself supplies I/O voltage, dropping it to 1.8V if necessary, from
>> VDD (vmmc). vqmmc only affects the host side, and whatever external pull-ups
>> that might exist.
>
> Ok.
>
>> > In which case, VCC-IO-WIFI is vmmc, and VCC-WIFI is just one of the
>> > wifi chip power rail, to be handled by a power sequence.
>>
>> For the WiFi chip, there is a separate IO-VCC rail, which is VCC-IO-WIFI.
>> This, from what I understand of the datasheet, is for I/O signaling, and
>> thus vqmmc. VCC-WIFI is what powers the chip, which is what vmmc is.
>
> Ok. but there's still the issue of the two regulators that needs to be
> kept in sync. Before, that, I'd rather stice to not tying them to the
> MMC bus, and putting a comment on top.

OK. Let's do that for now.

ChenYu
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux