On Fri, Jun 17, 2016 at 04:57:14PM +0800, Songjun Wu wrote:
> DT binding documentation for ISC driver.
>
> Signed-off-by: Songjun Wu <songjun.wu@xxxxxxxxx>
> ---
>
> Changes in v5:
> - Add clock names.
>
> Changes in v4:
> - Remove the isc clock nodes.
>
> Changes in v3:
> - Remove the 'atmel,sensor-preferred'.
> - Modify the isc clock node according to the Rob's remarks.
>
> Changes in v2:
> - Remove the unit address of the endpoint.
> - Add the unit address to the clock node.
> - Avoid using underscores in node names.
> - Drop the "0x" in the unit address of the i2c node.
> - Modify the description of 'atmel,sensor-preferred'.
> - Add the description for the ISC internal clock.
>
> .../devicetree/bindings/media/atmel-isc.txt | 64 ++++++++++++++++++++++
> 1 file changed, 64 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/atmel-isc.txt
>
> diff --git a/Documentation/devicetree/bindings/media/atmel-isc.txt b/Documentation/devicetree/bindings/media/atmel-isc.txt
> new file mode 100644
> index 0000000..9558a77
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/atmel-isc.txt
> @@ -0,0 +1,64 @@
> +Atmel Image Sensor Controller (ISC)
> +----------------------------------------------
> +
> +Required properties for ISC:
> +- compatible
> + Must be "atmel,sama5d2-isc".
> +- reg
> + Physical base address and length of the registers set for the device.
> +- interrupts
> + Should contain IRQ line for the ISC.
> +- clocks
> + List of clock specifiers, corresponding to entries in
> + the clock-names property;
> + Please refer to clock-bindings.txt.
> +- clock-names
> + Required elements: "hclock".
What about the 2 other clocks in the example?
> +- #clock-cells
> + Should be 0.
> +- clock-output-names
> + Should contain the name of the clock driving the sensor master clock.
State what the name is.
> +- pinctrl-names, pinctrl-0
> + Please refer to pinctrl-bindings.txt.
> +
> +ISC supports a single port node with parallel bus. It should contain one
> +'port' child node with child 'endpoint' node. Please refer to the bindings
> +defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +Example:
> +isc: isc@f0008000 {
> + compatible = "atmel,sama5d2-isc";
> + reg = <0xf0008000 0x4000>;
> + interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>;
> + clocks = <&isc_clk>, <&iscck>, <&isc_gclk>;
> + clock-names = "hclock", "iscck", "gck";
> + #clock-cells = <0>;
> + clock-output-names = "isc-mck";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>;
> +
> + port {
> + isc_0: endpoint {
> + remote-endpoint = <&ov7740_0>;
> + hsync-active = <1>;
> + vsync-active = <0>;
> + pclk-sample = <1>;
> + };
> + };
> +};
> +
> +i2c1: i2c@fc028000 {
> + ov7740: camera@21 {
> + compatible = "ovti,ov7740";
Indentation is still wrong here...
> + reg = <0x21>;
> + clocks = <&isc>;
> + clock-names = "xvclk";
> + assigned-clocks = <&isc>;
> + assigned-clock-rates = <24000000>;
> +
> + port {
> + ov7740_0: endpoint {
> + remote-endpoint = <&isc_0>;
> + };
> + };
> +};
> --
> 2.7.4
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
