On Thursday 16 June 2016 07:23 PM, Yendapally Reddy Dhananjaya Reddy wrote:
> This patch adds support for Broadcom NSP SATA3 PHY in existing
> Broadcom SATA PHY driver.
>
> Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@xxxxxxxxxxxx>
Acked-by: Kishon Vijay Abraham I <kishon@xxxxxx>
> ---
> drivers/phy/phy-brcm-sata.c | 81 +++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 81 insertions(+)
>
> diff --git a/drivers/phy/phy-brcm-sata.c b/drivers/phy/phy-brcm-sata.c
> index 6c4c5cb..18d6626 100644
> --- a/drivers/phy/phy-brcm-sata.c
> +++ b/drivers/phy/phy-brcm-sata.c
> @@ -45,6 +45,7 @@ enum brcm_sata_phy_version {
> BRCM_SATA_PHY_STB_28NM,
> BRCM_SATA_PHY_STB_40NM,
> BRCM_SATA_PHY_IPROC_NS2,
> + BRCM_SATA_PHY_IPROC_NSP,
> };
>
> struct brcm_sata_port {
> @@ -73,6 +74,13 @@ enum sata_phy_regs {
>
> PLL_REG_BANK_0 = 0x050,
> PLL_REG_BANK_0_PLLCONTROL_0 = 0x81,
> + PLLCONTROL_0_FREQ_DET_RESTART = BIT(13),
> + PLLCONTROL_0_FREQ_MONITOR = BIT(12),
> + PLLCONTROL_0_SEQ_START = BIT(15),
> + PLL_CAP_CONTROL = 0x85,
> + PLL_ACTRL2 = 0x8b,
> + PLL_ACTRL2_SELDIV_MASK = 0x1f,
> + PLL_ACTRL2_SELDIV_SHIFT = 9,
>
> PLL1_REG_BANK = 0x060,
> PLL1_ACTRL2 = 0x82,
> @@ -80,6 +88,7 @@ enum sata_phy_regs {
> PLL1_ACTRL4 = 0x84,
>
> OOB_REG_BANK = 0x150,
> + OOB1_REG_BANK = 0x160,
> OOB_CTRL1 = 0x80,
> OOB_CTRL1_BURST_MAX_MASK = 0xf,
> OOB_CTRL1_BURST_MAX_SHIFT = 12,
> @@ -271,6 +280,73 @@ static int brcm_ns2_sata_init(struct brcm_sata_port *port)
> return 0;
> }
>
> +static int brcm_nsp_sata_init(struct brcm_sata_port *port)
> +{
> + struct brcm_sata_phy *priv = port->phy_priv;
> + struct device *dev = port->phy_priv->dev;
> + void __iomem *base = priv->phy_base;
> + unsigned int oob_bank;
> + unsigned int val, try;
> +
> + /* Configure OOB control */
> + if (port->portnum == 0)
> + oob_bank = OOB_REG_BANK;
> + else if (port->portnum == 1)
> + oob_bank = OOB1_REG_BANK;
> + else
> + return -EINVAL;
> +
> + val = 0x0;
> + val |= (0x0f << OOB_CTRL1_BURST_MAX_SHIFT);
> + val |= (0x06 << OOB_CTRL1_BURST_MIN_SHIFT);
> + val |= (0x0f << OOB_CTRL1_WAKE_IDLE_MAX_SHIFT);
> + val |= (0x06 << OOB_CTRL1_WAKE_IDLE_MIN_SHIFT);
> + brcm_sata_phy_wr(base, oob_bank, OOB_CTRL1, 0x0, val);
> +
> + val = 0x0;
> + val |= (0x2e << OOB_CTRL2_RESET_IDLE_MAX_SHIFT);
> + val |= (0x02 << OOB_CTRL2_BURST_CNT_SHIFT);
> + val |= (0x16 << OOB_CTRL2_RESET_IDLE_MIN_SHIFT);
> + brcm_sata_phy_wr(base, oob_bank, OOB_CTRL2, 0x0, val);
> +
> +
> + brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_ACTRL2,
> + ~(PLL_ACTRL2_SELDIV_MASK << PLL_ACTRL2_SELDIV_SHIFT),
> + 0x0c << PLL_ACTRL2_SELDIV_SHIFT);
> +
> + brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_CAP_CONTROL,
> + 0xff0, 0x4f0);
> +
> + val = PLLCONTROL_0_FREQ_DET_RESTART | PLLCONTROL_0_FREQ_MONITOR;
> + brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
> + ~val, val);
> + val = PLLCONTROL_0_SEQ_START;
> + brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
> + ~val, 0);
> + mdelay(10);
> + brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
> + ~val, val);
> +
> + /* Wait for pll_seq_done bit */
> + try = 50;
> + while (try--) {
> + val = brcm_sata_phy_rd(base, BLOCK0_REG_BANK,
> + BLOCK0_XGXSSTATUS);
> + if (val & BLOCK0_XGXSSTATUS_PLL_LOCK)
> + break;
> + msleep(20);
> + }
> + if (!try) {
> + /* PLL did not lock; give up */
> + dev_err(dev, "port%d PLL did not lock\n", port->portnum);
> + return -ETIMEDOUT;
> + }
> +
> + dev_dbg(dev, "port%d initialized\n", port->portnum);
> +
> + return 0;
> +}
> +
> static int brcm_sata_phy_init(struct phy *phy)
> {
> int rc;
> @@ -284,6 +360,9 @@ static int brcm_sata_phy_init(struct phy *phy)
> case BRCM_SATA_PHY_IPROC_NS2:
> rc = brcm_ns2_sata_init(port);
> break;
> + case BRCM_SATA_PHY_IPROC_NSP:
> + rc = brcm_nsp_sata_init(port);
> + break;
> default:
> rc = -ENODEV;
> };
> @@ -303,6 +382,8 @@ static const struct of_device_id brcm_sata_phy_of_match[] = {
> .data = (void *)BRCM_SATA_PHY_STB_40NM },
> { .compatible = "brcm,iproc-ns2-sata-phy",
> .data = (void *)BRCM_SATA_PHY_IPROC_NS2 },
> + { .compatible = "brcm,iproc-nsp-sata-phy",
> + .data = (void *)BRCM_SATA_PHY_IPROC_NSP },
> {},
> };
> MODULE_DEVICE_TABLE(of, brcm_sata_phy_of_match);
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
