This patch adds support for Broadcom NSP SATA3 PHY in existing
Broadcom SATA PHY driver.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@xxxxxxxxxxxx>
---
drivers/phy/phy-brcm-sata.c | 81 +++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 81 insertions(+)
diff --git a/drivers/phy/phy-brcm-sata.c b/drivers/phy/phy-brcm-sata.c
index 6c4c5cb..18d6626 100644
--- a/drivers/phy/phy-brcm-sata.c
+++ b/drivers/phy/phy-brcm-sata.c
@@ -45,6 +45,7 @@ enum brcm_sata_phy_version {
BRCM_SATA_PHY_STB_28NM,
BRCM_SATA_PHY_STB_40NM,
BRCM_SATA_PHY_IPROC_NS2,
+ BRCM_SATA_PHY_IPROC_NSP,
};
struct brcm_sata_port {
@@ -73,6 +74,13 @@ enum sata_phy_regs {
PLL_REG_BANK_0 = 0x050,
PLL_REG_BANK_0_PLLCONTROL_0 = 0x81,
+ PLLCONTROL_0_FREQ_DET_RESTART = BIT(13),
+ PLLCONTROL_0_FREQ_MONITOR = BIT(12),
+ PLLCONTROL_0_SEQ_START = BIT(15),
+ PLL_CAP_CONTROL = 0x85,
+ PLL_ACTRL2 = 0x8b,
+ PLL_ACTRL2_SELDIV_MASK = 0x1f,
+ PLL_ACTRL2_SELDIV_SHIFT = 9,
PLL1_REG_BANK = 0x060,
PLL1_ACTRL2 = 0x82,
@@ -80,6 +88,7 @@ enum sata_phy_regs {
PLL1_ACTRL4 = 0x84,
OOB_REG_BANK = 0x150,
+ OOB1_REG_BANK = 0x160,
OOB_CTRL1 = 0x80,
OOB_CTRL1_BURST_MAX_MASK = 0xf,
OOB_CTRL1_BURST_MAX_SHIFT = 12,
@@ -271,6 +280,73 @@ static int brcm_ns2_sata_init(struct brcm_sata_port *port)
return 0;
}
+static int brcm_nsp_sata_init(struct brcm_sata_port *port)
+{
+ struct brcm_sata_phy *priv = port->phy_priv;
+ struct device *dev = port->phy_priv->dev;
+ void __iomem *base = priv->phy_base;
+ unsigned int oob_bank;
+ unsigned int val, try;
+
+ /* Configure OOB control */
+ if (port->portnum == 0)
+ oob_bank = OOB_REG_BANK;
+ else if (port->portnum == 1)
+ oob_bank = OOB1_REG_BANK;
+ else
+ return -EINVAL;
+
+ val = 0x0;
+ val |= (0x0f << OOB_CTRL1_BURST_MAX_SHIFT);
+ val |= (0x06 << OOB_CTRL1_BURST_MIN_SHIFT);
+ val |= (0x0f << OOB_CTRL1_WAKE_IDLE_MAX_SHIFT);
+ val |= (0x06 << OOB_CTRL1_WAKE_IDLE_MIN_SHIFT);
+ brcm_sata_phy_wr(base, oob_bank, OOB_CTRL1, 0x0, val);
+
+ val = 0x0;
+ val |= (0x2e << OOB_CTRL2_RESET_IDLE_MAX_SHIFT);
+ val |= (0x02 << OOB_CTRL2_BURST_CNT_SHIFT);
+ val |= (0x16 << OOB_CTRL2_RESET_IDLE_MIN_SHIFT);
+ brcm_sata_phy_wr(base, oob_bank, OOB_CTRL2, 0x0, val);
+
+
+ brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_ACTRL2,
+ ~(PLL_ACTRL2_SELDIV_MASK << PLL_ACTRL2_SELDIV_SHIFT),
+ 0x0c << PLL_ACTRL2_SELDIV_SHIFT);
+
+ brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_CAP_CONTROL,
+ 0xff0, 0x4f0);
+
+ val = PLLCONTROL_0_FREQ_DET_RESTART | PLLCONTROL_0_FREQ_MONITOR;
+ brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
+ ~val, val);
+ val = PLLCONTROL_0_SEQ_START;
+ brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
+ ~val, 0);
+ mdelay(10);
+ brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
+ ~val, val);
+
+ /* Wait for pll_seq_done bit */
+ try = 50;
+ while (try--) {
+ val = brcm_sata_phy_rd(base, BLOCK0_REG_BANK,
+ BLOCK0_XGXSSTATUS);
+ if (val & BLOCK0_XGXSSTATUS_PLL_LOCK)
+ break;
+ msleep(20);
+ }
+ if (!try) {
+ /* PLL did not lock; give up */
+ dev_err(dev, "port%d PLL did not lock\n", port->portnum);
+ return -ETIMEDOUT;
+ }
+
+ dev_dbg(dev, "port%d initialized\n", port->portnum);
+
+ return 0;
+}
+
static int brcm_sata_phy_init(struct phy *phy)
{
int rc;
@@ -284,6 +360,9 @@ static int brcm_sata_phy_init(struct phy *phy)
case BRCM_SATA_PHY_IPROC_NS2:
rc = brcm_ns2_sata_init(port);
break;
+ case BRCM_SATA_PHY_IPROC_NSP:
+ rc = brcm_nsp_sata_init(port);
+ break;
default:
rc = -ENODEV;
};
@@ -303,6 +382,8 @@ static const struct of_device_id brcm_sata_phy_of_match[] = {
.data = (void *)BRCM_SATA_PHY_STB_40NM },
{ .compatible = "brcm,iproc-ns2-sata-phy",
.data = (void *)BRCM_SATA_PHY_IPROC_NS2 },
+ { .compatible = "brcm,iproc-nsp-sata-phy",
+ .data = (void *)BRCM_SATA_PHY_IPROC_NSP },
{},
};
MODULE_DEVICE_TABLE(of, brcm_sata_phy_of_match);
--
2.1.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
