On Fri, Jun 03, 2016 at 11:56:28AM +0200, LABBE Corentin wrote:
> This patch adds documentation for Device-Tree bindings for the
> Allwinner sun8i-emac driver.
>
> Signed-off-by: LABBE Corentin <clabbe.montjoie@xxxxxxxxx>
> ---
> .../bindings/net/allwinner,sun8i-emac.txt | 64 ++++++++++++++++++++++
> 1 file changed, 64 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
>
> diff --git a/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
> new file mode 100644
> index 0000000..cf71a71
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
> @@ -0,0 +1,64 @@
> +* Allwinner sun8i EMAC ethernet controller
> +
> +Required properties:
> +- compatible: "allwinner,sun8i-a83t-emac", "allwinner,sun8i-h3-emac",
> + or "allwinner,sun50i-a64-emac"
> +- reg: address and length of the register sets for the device.
> +- reg-names: should be "emac" and "syscon", matching the register sets
Is syscon shared with other devices? Your example only has 1 reg
address.
> +- interrupts: interrupt for the device
> +- clocks: A phandle to the reference clock for this device
> +- clock-names: should be "ahb"
> +- resets: A phandle to the reset control for this device
> +- reset-names: should be "ahb"
> +- phy-mode: See ethernet.txt
> +- phy or phy-handle: See ethernet.txt
> +- #address-cells: shall be 1
> +- #size-cells: shall be 0
> +
> +"allwinner,sun8i-h3-emac" also requires:
> +- clocks: an extra phandle to the reference clock for the EPHY
> +- clock-names: an extra "ephy" entry matching the clocks property
> +- resets: an extra phandle to the reset control for the EPHY
> +- resets-names: an extra "ephy" entry matching the resets property
> +
> +See ethernet.txt in the same directory for generic bindings for ethernet
> +controllers.
> +
> +The device node referenced by "phy" or "phy-handle" should be a child node
> +of this node. See phy.txt for the generic PHY bindings.
> +
> +Optional properties:
> +- phy-supply: phandle to a regulator if the PHY needs one
> +- phy-io-supply: phandle to a regulator if the PHY needs a another one for I/O.
> + This is sometimes found with RGMII PHYs, which use a second
> + regulator for the lower I/O voltage.
These should go in the phy's node.
> +- allwinner,tx-delay: The setting of the TX clock delay chain
> +- allwinner,rx-delay: The setting of the RX clock delay chain
> +
> +The TX/RX clock delay chain settings are board specific.
> +
> +Optional properties for "allwinner,sun8i-h3-emac":
> +- allwinner,use-internal-phy: Use the H3 SoC's internal E(thernet) PHY
> +- allwinner,leds-active-low: EPHY LEDs are active low
> +
> +When the internal PHY is requested, the implementation shall configure the
> +internal PHY to use the address specified in the child PHY node.
> +
> +Example:
> +
> +emac: ethernet@01c0b000 {
> + compatible = "allwinner,sun8i-h3-emac";
> + reg = <0x01c0b000 0x1000>;
> + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&bus_gates 17>, <&bus_gates 128>;
> + clock-names = "ahb", "ephy";
> + resets = <&ahb_rst 17>, <&ahb_rst 66>;
> + reset-names = "ahb", "ephy";
> + phy = <&phy1>;
> + allwinner,use-internal-phy;
> + allwinner,leds-active-low;
> +
> + phy1: ethernet-phy@1 {
> + reg = <1>;
> + };
> +};
> --
> 2.7.3
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
