From: Christopher Spinrath <christopher.spinrath@xxxxxxxxxxxxxx>
The cm-fx6 module has an on-board spi-flash chip for its firmware, an
eeprom (containing e.g. the mac address of the on-board Ethernet),
a sata port, a pcie controller, an USB hub, and an USB otg port.
Enable support for them. In addition, enable syscon poweroff support.
Signed-off-by: Christopher Spinrath <christopher.spinrath@xxxxxxxxxxxxxx>
---
Changes since v1:
- remove regulator pseudo-bus
- remove partition layout from spi flash node
- remove unneeded label of the spi flash node
- convert downstream power-on-gpio property of pcie node to a proper
regulator
- sort usb* related nodes alphabetically
- make use of GPIO_ACTIVE_{LOW,HIGH} defines
- replace 0x80000000 iomuxc configs by proper defaults obtained from
u-boot
arch/arm/boot/dts/imx6q-cm-fx6.dts | 125 +++++++++++++++++++++++++++++++++++++
1 file changed, 125 insertions(+)
diff --git a/arch/arm/boot/dts/imx6q-cm-fx6.dts b/arch/arm/boot/dts/imx6q-cm-fx6.dts
index 21c513f..c6f0e58 100644
--- a/arch/arm/boot/dts/imx6q-cm-fx6.dts
+++ b/arch/arm/boot/dts/imx6q-cm-fx6.dts
@@ -12,6 +12,7 @@
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include "imx6q.dtsi"
/ {
@@ -31,6 +32,49 @@
linux,default-trigger = "heartbeat";
};
};
+
+ reg_pcie_power_on_gpio: regulator-pcie-power-on-gpio {
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-pcie-power-on-gpio";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_h1_vbus: usb_h1_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_otg_vbus: usb_otg_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>, <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p", "jedec,spi-nor";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
};
&fec {
@@ -46,7 +90,30 @@
status = "okay";
};
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+ clock-frequency = <100000>;
+
+ eeprom@50 {
+ compatible = "at24,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x100b1
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x100b1
+ >;
+ };
+
pinctrl_enet: enetgrp {
fsl,pins = <
MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
@@ -90,12 +157,55 @@
>;
};
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b1
+ MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b1
+ >;
+ };
+
pinctrl_uart4: uart4grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
>;
};
+
+ pinctrl_usbh1: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x130b0
+ >;
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ vdd-supply = <®_pcie_power_on_gpio>;
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
};
&uart4 {
@@ -103,3 +213,18 @@
pinctrl-0 = <&pinctrl_uart4>;
status = "okay";
};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ dr_mode = "otg";
+ status = "okay";
+};
--
2.8.3
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
