Hi Ricard,
On Thu, 2 Jun 2016 09:47:18 +0200
Ricard Wanderlof <ricard.wanderlof@xxxxxxxx> wrote:
> Devicetree bindings for the driver for the Evatronix NANDFLASH-CTRL NAND flash
> controller IP. This controller is used in the Axis ARTPEC-6 SoC.
>
> The driver supports BCH ECC using the controller's hardware, but there is
> also an option to use software BCH ECC. However, the ECC layouts are not
> compatible so it's not possible to mix them. The main advantage to using
> software ECC is that there are more OOB bytes free, as the hardware is
> slightly wasteful on OOB space.
>
> BCH ECC from 4 to 32 bits over 256, 512 or 1024 byte ECC blocks is supported.
>
> Only large-page flash chips are supported, using 4 or 5 address cycles.
>
> Signed-off-by: Ricard Wanderlof <ricardw@xxxxxxxx>
> ---
> .../devicetree/bindings/mtd/evatronix-nand.txt | 44 ++++++++++++++++++++
> .../devicetree/bindings/vendor-prefixes.txt | 1 +
> 2 files changed, 45 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mtd/evatronix-nand.txt
>
> diff --git a/Documentation/devicetree/bindings/mtd/evatronix-nand.txt b/Documentation/devicetree/bindings/mtd/evatronix-nand.txt
> new file mode 100644
> index 0000000..7ceb95a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mtd/evatronix-nand.txt
> @@ -0,0 +1,44 @@
> +Evatronix NANDFLASH-CTRL NAND flash controller
> +
> +Required properties:
> +- compatible : "evatronix,nandflash-ctrl"
> +- reg : specify bus address and register area size.
> +- interrupts : controller interrupt number and irq type.
> +- nand-ecc-mode : See nand.txt. Supported values "hw", "soft".
> +- nand-ecc-algo : See nand.txt. Supported value "bch".
> +- nand-ecc-strength : See nand.txt. Supported values: 4, 8, 16, 24, 32.
> +- nand-ecc-step-size : See nand.txt. Supported values: 256, 512, 1024.
> +
> +Optional properties:
> +- nand-on-flash-bbt: See nand.txt.
> +- #address-cells, #size-cells: See partition.txt.
> +- evatronix,use-bank-select : Use controller bank select function to access
> + multiple chips, rather than chip enable.
You mean, using a dedicated logic to control the CS lines rather than a
GPIO (controlled by the SW using gpio_set_value())?
It that's the case then I suggest doing it the other way around.
When you want to use a plain GPIO you should define something like:
cs-gpios = <&pioC X>;
If it's not there the controller should use it's internal logic to
control the CS line.
BTW, you seem to support controlling several CS using the same
controller, which means you'll have to specify which CS the NAND chip
is connected to (see [1]).
> +- evatronix,rb-wired-and: Assume ready/busy signal from all flash chips are
> + connected using a wired-AND topology rather than
> + individually.
Hm, is that really required? If the R/B line is shared among several
NAND chips, it should be transparent, you just have to specific which
chip is connected to which GPIO (or dedicated R/B pin).
> +- evatronix,timings: Seven 32-bit values for initializing the TIME_SEQ_0,
> + TIME_SEQ_1, TIMINGS_ASYN, TIME_GEN_SEQ_0, TIME_GEN_SEQ_1,
> + TIME_GEN_SEQ_2 and TIME_GEN_SEQ_3 registers, respectively.
Can this be extracted from the timing mode exposed by the NAND chip.
IMO it shouldn't be defined in the DT.
> +
> +Example:
> +
> +nand: nand@f801e000 {
> + compatible = "evatronix,nandflash-ctrl";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0xf801e000 0x0200>;
> + interrupts = <0 139 IRQ_TYPE_LEVEL_HIGH>;
> + /* ONFi mode 0 timing, assuming 100 MHz clock. */
> + /* Order is TIME_SEQ_0, TIME_SEQ_1, TIMINGS_ASYN,
> + * TIME_GEN_SEQ_0, _1, _2, _3 */
> + evatronix,timings = <0x0d151533 0x000b0515 0x00000046
> + 0x00150000 0x00000000 0x00000005 0x00000015>;
> + nand-ecc-mode = "hw";
> + nand-ecc-algo = "bch";
> + nand-on-flash-bbt;
> + nand-ecc-strength = <8>;
> + nand-ecc-step-size = <512>;
> + evatronix,use-bank-select;
> + evatronix,rb-wired-and;
> +};
We recently added more constraints on the 'NAND controller/NAND chip'
representation in the DT [1].
You should rework your binding (and your code) to match these
constraints, even if you controller is only able to interface with a
single NAND chip.
Thanks,
Boris
[1]https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/mtd/nand.txt
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index 86740d4..4018162 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -83,6 +83,7 @@ epson Seiko Epson Corp.
> est ESTeem Wireless Modems
> ettus NI Ettus Research
> eukrea Eukréa Electromatique
> +evatronix Evatronix SA
> everest Everest Semiconductor Co. Ltd.
> everspin Everspin Technologies, Inc.
> excito Excito
--
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
